window RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Workshop Manual

87B-7
MR-413-X44-87B000$096.mif
V5
87B
ENGINE HARNESS
FRONT ENGINE WIRING & ADDITIONAL HEADLIGHTS
DOOR WIRING
CEILING WIRING
PASSENGER COMPARTMENT WIRING
REAR BUMPER WIRING
TAILGATE WIRING
1UCH
2Passenger Compartment Relay/Fuse Box
3Electric power-assisted steering.
4Transponder ring.
5Air conditioning panel.
6One touch window/anti-pinch module.
7Exterior temperature sensor.
8Rain/light sensor & interior temperature sensor.
9Anti-pinch/sunroof.
2ABS computer.
2Injection computer.
3Preheating unit.
4Sequential gearbox computer.
5Engine fuse and relay box.
6Alternator.
7
2
61
2
3
5
4
8
5
7
43
1
6
9
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding
- List and location of components
MR-413-X44-87B000$096.mif
UCH
Vdiag No.: 44

87B-8
MR-413-X44-87B000$144.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Operating diagram
1UCH.
2Air conditioning.
3Interior lighting.
4Exterior lighting, signals.
5One touch windows and electric sunroof.
6Alarm.
7Radiofrequency key.
8Starter.
9Opening elements.
10 Front/rear wipers, washers.
11 Alternator.
12 BSS* connection
*BSS: (see Role of components, Role of connection BSS).
1
8
3
2
11
10
9
7
6
5
4
12
MR-413-X44-87B000$144.mif
UCH
Vdiag No.: 44

87B-11
MR-413-X44-87B000$192.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Role of components87B
Functions managed by the different UCH ranges on the New Twingo:
* CPE: Electric central door locking
* CAR: Automatic locking when drivingL1
Entry levelL2
Mid-rangeL3
Top of the
range
UCH reprogrammingXX X
Multiplex connectionXX X
Fault findingXX X
Access - Protection X X X
Transponder keyX
Transponder and radiofrequency keyXX
Engine immobiliserXX X
+ Accessories feed controlXX X
Alarm management (predisposition)XX
Locking and unlocking using electric central door locking buttonXX
DeadlockingX
Locking when driving (CAR*)XX
Automatic unlocking (in the event of impact)XX
Engine thermal protectionXX X
Automatic re-lockingXX
One-touch electric windowsX
Tailgate electric lockXX X
Tailgate opening switchXX X
Tailgate locking switch (with key)X
Air conditioning
Electric heated rear screen managementXX X
Air conditioning request managementXX
Automatic climate control management (via CAN network)XX
External temperature managementXX

87B-13
MR-413-X44-87B000$240.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Replacement of components
When replacing the UCH (see MR 411, Mechanical systems, 87B, Passenger compartment connection unit).
If replacing the computer, carry out the programming and configuration operations described (see configurations
and programming).
The order of programming and configuration operations is as follows:
1 - Write the VIN, using command VP004 Write VIN.
2 - Program the UCH using command SC004 UCH programming.
3 - Configuration of the UCH (in the Configuration and programming menu) using the following commands:
CF031 Calibration,
CF019 Type of heating and air conditioning system,
CF028 Engine type,
CF171 Temperature display,
CF029 External temperature sensor,
CF173 One-touch windows/sunroof (SR)*.
CF032 See-me-home lighting,
CF021 Front fog lights,
CF014 Daytime running lights
CF193 Automatic headlight function,
CF194 Automatic wiping function,
CF035 Rain/light sensor,
CF191 Wiper intermittent speed ring,
CF024 Hazard warning lights activated by ABS,
CF108 Locking via the RAID,
CF009 Deadlocking,
CF192 Central door locking,
CF195 Type of key,
CF229 Alarm.
4 - Key allocation, using command SC015 Key allocation.
5 - Configuration of the multiplex network is used to define (in the UCH) the different computers present and which
support fault finding on the multiplex network.
* TO: Sunroof.
MR-413-X44-87B000$240.mif

UCH
Vdiag No.: 44

87B-22
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
UCH CONFIGURATIONS
List of individual configurations available on the diagnostic tool with the associated configuration reading.
* SR: Sunroof.
*RF: radio frequencyConfigurationConfiguration
readingName of configuration Choice of configuration
CF031 "Calibration",To be performed if replacing
the UCH.
CF019 LC013"Type of heating and air conditioning
system",HEATING/MANUAL/
AUTOMATIC
CF028 LC023 "Engine type",Configuration. 1 (K9K)
Configuration. 2 (D7F/D4F
without air conditioning)
Configuration. 3 (other engine)
CF171 LC067 "Temperature display"WITH/WITHOUT
CF029 LC002 "Exterior temperature sensor",WITH/WITHOUT
CF173 LC070 "One-touch windows/SR*",WITH/WITHOUT
CF032 LC025 "See-me-home lighting",WITH/WITHOUT
CF021 LC015 "Front fog lights"WITH/WITHOUT
CF014 LC008 "Daytime running lights",WITH/WITHOUT
CF193 LC095 "Automatic headlighting function",WITH/WITHOUT
CF194 LC096 "Automatic wiping function",WITH/WITHOUT
CF035 LC044 "Rain/light sensor", PRESENT/ABSENT
CF191 LC094 "Wiper intermittent speed ring",WITH/WITHOUT
CF024 LC018"Hazard warning lights switched on by
ABS",WITH/WITHOUT
CF108 LC040 "Automatic locking when driving",WITH/WITHOUT
CF009 LC003 "Deadlocking",WITH/WITHOUT
CF192 LC093 "Central door locking",WITH/WITHOUT
CF195 LC097 "Type of key". STANDARD/RF*
CF229 LC126 "Alarm".WITH/WITHOUT

87B-24
MR-413-X44-87B000$336.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
Summary of sensors and actuators on which the UCH can carry out fault finding (with the corresponding
engineering office codes).
Tool fault Associated DTC Diagnostic tool title
DF0019510 UCH
DF0119522 Rain/light sensor circuit
DF01295D1 Right-hand direction indicator circuit
DF01395D0 Left-hand direction indicator circuit
DF0279550 External temperature sensor circuit
DF04095A0 Rear screen wiper park position
DF0419560 Heated rear screen warning light circuit
DF0429558 Air conditioning warning light circuit
DF0549501 Computer
DF0629580 Starter relay control circuit
DF06595F0 Electric window authorisation connection
DF0829570 Door locking button indicator light circuit
DF08795C2 Side lights relay control circuit
DF08895C3 Dipped beam headlights relay control circuit
DF09795 A1 Windscreen wiper park position control
DF09895C4 Main beam headlight relay control circuit
DF10895C5 Front fog lights control circuit
DF10995C6 Rear fog lights control circuit
DF1339574 Deadlocking motor(s) circuit
DF13495D2 Hazard warning lights indicator light circuit
DF1359520 Rain detector
DF1369521 Light sensor
DF13796B1 UCH - Alternator connection
DF13896B2 Alternator
DF1399660 Interior lights
DF14096B3 Voltage regulator
DF21295B0 Alarm circuit
MR-413-X44-87B000$336.mif
UCH
Vdiag No.: 44

87B-26
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF011
PRESENT
OR
STOREDRAIN/LIGHT SENSOR CIRCUIT
1.DEF : Open circuit or short circuit
NOTESConditions for applying the fault finding procedure to stored faults:
Switch on the ignition, activate automatic headlighting by quickly performing the
following manipulation twice: control stalk (component code 209) on zero position →
control stalk (component code 209) in Side light position.
Status ET114 “Wiper request by rain sensor” should be “Low speed” or “High
speed” when the water runs over the rain/light sensor on the windscreen or
status ET115 “Request for lights to be switched on by light sensor” should be
“Present” by placing an opaque cover over the rain/light sensor.
Note:
If there is an open circuit on connection BPT, there is a malfunction on the
electric windows, rain/light sensor, interior light(s) and luggage compartment
light.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the function is not deactivated, quickly perform the following cycle twice to activate the automatic
headlighting function: Monolever (component code 209) OFF → Monolever (component code 209) in Side light
ON position.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that LC044 "Rain/light sensor" displays "Present". If not, carry out CF035 "Rain/light sensor".
Check that LC096 "Automatic wiper function" displays "With". If not, carry out CF194 "Automatic wiper
function".
Check that LC095 "Automatic headlight function", displays "With". If not, carry out CF193 "Automatic
headlight function".
Check the condition and the positioning of fuses F2 (15A), F8 (15A), F19 (5A), F27 (5 A) depending on the
equipment and F29 (15A) on the passenger compartment fuse and relay box (component code 1016).
Replace the fuse(s) or repair if necessary.
Check the condition and connection of the PE1, PE2 and PE3 connectors of the UCH (component code 645)
(tabs pushed back, oxidised, broken).
Check for + after ignition feed on connection AP43 of component 645.
Check for + accessories feed on connection SP2 (for vehicles fitted with a manual gearbox) or SP15
(for vehicles fitted with a sequential gearbox) of component 645.
Check for earth on connection NAM of component 645. Check the earth on connection MAM of component 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF011

87B-40
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
* SR: SunroofDF065
PRESENT
OR
STORED
ELECTRIC WINDOWS AUTHORISATION CONNECTION
CC.1 : Short circuit to + 12 volts
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
The ignition is switched of f and back on again after pressing the driver's one-touch
electric window switch or sunroof switch if the vehicle is fitted with a sunroof.
For vehicles fitted with sunroof (component code 1578):
Check that the vehicle is configured with One-touch window(s) S.R*. :
Check that LC070 One-touch window(s) S.R. is With. Otherwise use CF173
One-touch window(s) S.R.
Check the condition and connection of the UCH 24-track connector PE2 (component code 645) (tabs bent,
oxidised or broken).
Check the condition and connection of the driver's electric window motor 6-track connector (bent, oxidised,
broken tabs).
If there is an electric sunroof, check that fuse F26 (20 A) is sound and correctly fitted in the passenger
compartment fuse and relay box (component 1016).
Replace the fuse if necessary.
If there is an electric sunroof, check the condition and connection of the A-pillar 4-track connector 339 and of
sunroof computer connector AA (tabs bent, oxidised, broken).
Check the insulation, continuity and absence of interference resistance of the following connections:
●Connection code 21K between components 203 and 645.
●Connection code MAM between component 203 and earth MAM.
For vehicles fitted with a sunroof:
●Connection code 21K between components 1579 and 645.
●Connection code MAM between component 1579 and earth MAM.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, switch on the ignition and check for 0 V on connection 21K if no (see 87D
electric windows - Sunroof).
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF065

87B-61
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF135
DF136
PRESENT
OR
STOREDRAIN DETECTOR
LIGHT SENSOR
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault reappears as present after:
Switching on the ignition, activating automatic headlight lighting by moving the control
stalk twice in quick succession as follows: control stalk (component code 209) to
position zero ΑΕ control stalk (component code 209) to side lights position.
Status ET114 "Wiper request from rain sensor" should be "Low speed" or "High
speed" when the water runs over the position of the rain/light sensor on the
windscreen or status ET115 "Request for lights to be switched on from light
sensor" should be "Present" when an opaque cover is placed over the rain/light
sensor.
Note:
If there is an open circuit on connection BPT, there will be a malfunction on the
electric window winders, on the rain/light sensor, on the interior lights and the boot
lighting.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the vehicle is configured with a rain/light sensor (component code 1415).
Check that LC044 Rain/light sensor is Present. If not, perform CF035 Rain/light sensor.
Check that LC096 Automatic wiper function displays With. If not, carry out CF194 "Automatic wiper
function".
Check that LC095 Automatic headlight function displays With. If not, carry out CF193 "Automatic headlight
function".
Check the condition and position of supply fuses F2 (15 A), F8 (15 A), F19 (5 A), F27 (5 A) according to the
equipment, F29 (15 A) of the rain/light sensor (component code 1415) on the passenger compartment fuse and
relay box (component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the 3-track connector of the rain/light sensor (component 1415) (tabs
bent, broken or oxidised).
Check the condition and connection of the PE2 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
Check for + 12 V on connection BPT of component 1415.
Check for earth on connection MAM of component 1415.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF135 / UCH_V44_DF136

87B-71
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: ACCESS
* SR: Sunroof.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
TailgateET061:Open tailgate
requestPRESENT
ABSENTIn the event of a fault, apply the
interpretation of status
ET061.
ET463:Door(s) or tailgateOPEN
CLOSEDIn the event of a fault, apply the
interpretation of status
ET463.
Locking/unlocking
buttonET186:Short press on door
closing buttonSignal can be
interpreted if the
ignition is switched off
(key removed from the
ignition switch).
ACTIVE = Remote
control door closing
button pressed for
longer than 2 seconds.
INACTIVE = Button not
pressed or pressed for
less than 2 seconds.In the event of a fault, refer to
the interpretation of status
ET186.
ET189:Long press on door
opening buttonACTIVE
INACTIVEIn the event of a fault, refer to
the interpretation of status
ET189.
Electric central locking
buttonET044:Central Locking
buttonDEPRESSED
RELEASEDIn the event of a fault, refer to
the interpretation of status
ET044.
One touch window /
SR*.ET087:One-touch window /
SR* authorisation.PRESENT
ABSENTIn the event of a fault, apply the
interpretation of status
ET087.
Locking commandAC004:Central door lockingThis command is used
to test whether central
door locking is workingIn the event of a fault, consult
the procedure for dealing
with command AC004.