window RENAULT TWINGO RS 2009 2.G Mechanism And Accessories User Guide

52A-8
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof operating mechanism: Removal - Refitting
52A
-the B-pillar upper trims (see B-pillar upper trim:
Removal - Refitting) (MR 412, 71A, Body internal
trim),
-the rear panel trims (see Rear panel lining: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the rear parcel shelf side trim panels (see Rear
parcel shelf side trim: Removal - Refitting) (MR
412, 71A, Body internal trim),
-the rear bench seatback (depending on equipment
level) (see Rear bench seatback: Removal - Re-
fitting) (MR 412, 76A, Rear seat frames and run-
ners),
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the sunroof console (see Sunroof switch: Remo-
val - Refitting) (MR 411, 87D, Electric window win-
ders - Sunroof),
-the sun visors (see 57A, Interior equipment, Sun
visor: Removal - Refitting, page 57A-16) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners).
aInitialise the sunroof motor (see Electric sunroof:
Initialisation) (MR 413, 87D, Electric windows - Su-
nroof).

52A-11
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof mobile panel: Removal - Refitting
52A
aOpen the mobile panel ensuring the guide brackets
are inserted into the side rails of the sunroof opera-
ting mechanism.
III - FINAL OPERATION.
aRefit:
-the detachable rail,
-the detachable rail bolt (3) ,
aTorque tighten the detachable rail bolt (2.5 N.m).
aInitialise the sunroof motor (see Electric sunroof:
Initialisation) (MR 413, 87D, Electric windows - Su-
nroof).
109102
Note:
In the event that the sunroof mobile panel jams, it
is necessary to remove the headlining (see Hea-
dlining: Removal - Refitting) (MR 412, 71A,
Body internal trim).

52A-14
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof deflector: Removal - Refitting
52A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aOpen the sunroof mobile panel.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the deflector bolts (1) .aRemove the deflector by pivoting it (2) towards the
rear.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the deflector at (2) .
aPosition the deflector return spring.
aKeep applying pressure to the deflector.
aRefit the deflector bolts (1) .
aTorque tighten the deflector bolts (2.5 Nm).
II - FINAL OPERATION.
aInitialise the sunroof motor (see Electric sunroof:
Initialisation) (MR 413, 87D, Electric windows - Su-
nroof). Tightening torquesm
deflector bolts2.5 Nm
121490
121491

54A-1
WINDOWS
Windscreen: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the windscreen wiper arms (see Winds-
creen wiper arm: Removal - Refitting) (MR 411,
85A, Washing - Wiping).
aRemove the lower trim pieces (1) from the winds-
creen.
aRemove:
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) ,
-the interior rear-view mirror (see 57A, Interior
equipment, Interior rear-view mirror: Removal -
Refitting, page 57A-14) ,
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim).
aDisconnect the rain and light sensor (depending on
the equipment level).II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the seal (2) from the windscreen.
aProtect the windscreen surround using masking ta-
pe.
aPosition the dashboard protector (Car. 1818).
a
aCut the cement bead. Special tooling required
Car. 1818Instr ument panel protector
Note:
Leave the rain sensor in place on the old winds-
creen during the replacement operation (depen-
ding on the equipment level).
119268
119271
108156
Note:
When cutting the cement bead, take care not to
cut the wiring harness.

54A-2
WINDOWS
Windscreen: Removal - Refitting
54A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aPosition the retaining shims and stops.
aPosition the seal (2) on the windscreen.
aFor preparation and bonding (see Technical Note
560A).
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the windscreen (this operation requires two
people).
aRespect the following clearances and flush fitting:
- « Windscreen - Roof » ,
- « Windscreen - A-pillar » .
aHold the windscreen in position with masking tape.
III - FINAL OPERATION.
aReplace the rain and light sensor adhesive base
(depending on the equipment level) (see Rain and
light sensor: Removal - Refitting) (MR 411, 85A,
Wiping - Washing).
aConnect the rain and light sensor (depending on the
equipment level).
aRefit:
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the interior rear-view mirror (see 57A, Interior
equipment, Interior rear-view mirror: Removal -
Refitting, page 57A-14) ,
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) ,
-the lower windscreen trims (1) ,
-the windscreen wiper arms (see Windscreen wi-
per arm: Removal - Refitting) (MR 411, 85A, Wi-
pers - Washers).

54A-3
WINDOWS
Front side door sliding window: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the front side door trim (see Front side door trim:
Removal - Refitting) (MR 412, 72A, Side opening
element trim),
-the interior weatherstrip,
-the door seal film (see Door sealing film: Remo-
val - Refitting) (MR 312, 65A, Opening elements
sealing).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aLower the window in order to access the bolts (1) of
the front side sliding door window.
aRemove the bolts (1) from the front side sliding door
window.aRemove the front side sliding door window.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front side door sliding window ,
-the bolts (1) to the front side sliding door window.
aCarry out a function test.
II - FINAL OPERATION.
aReplace the door sealing film (see Door sealing
film: Removal - Refitting) (MR 312, 65A, Opening
elements sealing).
aRefit:
-the interior weatherstrip,
-the door trim (see Front side door trim: Removal
- Refitting) (MR 412, 72A, Side opening element
trim). Note:
When removing the seal film, it must be replaced (
(see Door sealing fi lm: Removal - Refitting) ).
119279
119292

54A-4
WINDOWS
Rear quarter panel window: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the rear panel trim (see Rear panel lining: Remo-
val - Refitting) (71A, Body internal trim),
-the rear quarter panel trim (see Quarter panel
trim: Removal - Refitting) (71A, Body internal
trim).
-the B-pillar upper trim (see B-pillar upper trim:
Removal - Refitting) (71A, Body internal trim).
aProtect the edges of the quarter panel window using
masking tape.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aBegin cutting the cement bead.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace the stops and shims.
aFor preparation and bonding (see Technical Note
560A).II - REFITTING OPERATION FOR PART
CONCERNED
aBond the rear quarter panel window.
aEqual out the clearances and shut lines.
aRemove the tabs from the stops when the adhesive
has dried.
III - FINAL OPERATION.
aRefit:
-the B-pillar upper trim (see B-pillar upper trim:
Removal - Refitting) (71A, Body internal trim),
-the rear quarter panel trim (see Quarter panel
trim: Removal - Refitting) (71A, Body internal
trim).
-the rear panel trim (see Rear panel lining: Remo-
val - Refitting) (71A, Body internal trim).
119267
Note:
Leave a minimum clearance of 3.5 mm between
the rear quar ter panel window and the upper
section of the panelwork. This clearance is
necessary for fitting the transverse bars.

54A-5
WINDOWS
Rear screen: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the rear screen wiper arm (see Rear
screen wiper arm: Removal - Refitting) (MR 411,
85A, Wiping - Washing).
aUnclip the exterior trim (1) from the rear screen.
aRemove the tailgate trim (see Tailgate trim: Remo-
val - Refitting) (MR 412, 73A, Non-side opening
element trim).
aDisconnect the rear screen de-icer connectors.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aProtect the edges of the rear screen using masking
tape.
aBegin cutting the cement bead.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace the stops and shims.
aFor preparation and bonding of the rear screen win-
dow, see Technical Note 560A, General window
and sunroof bonding procedure.
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the rear screen (two people are required for
this operation).
aEqual out the clearances and shut lines.
aRemove the tabs from the stops when the adhesive
has dried.
III - FINAL OPERATION.
aConnect the rear screen de-icer connectors.
aRefit the tailgate trim (see Tailgate trim: Removal -
Refitting) (MR 412, 73A, Non-side opening element
trim).
aClip on the rear screen exterior trim (1) .
119525
119290

54A-6
WINDOWS
Rear screen: Removal - Refitting
54A
aRefit the rear screen wiper arm (see Rear screen
wiper arm: Removal - Refitting) (MR 411, Mecha-
nical 85A, Wiping - Washing).

54A-7
WINDOWS
Sunroof fixed window: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) .
aProtect:
-the sunroof's fixed window surround and the rear
section of the roof using masking tape,
-the inside of the vehicle.II - REMOVAL OPERATION FOR PART
CONCERNED
aCut the cement bead; this operation requires two
people.
aRemove the fixed window from the sunroof.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aPosition the new shims on the sunroof operating me-
chanism.
aFor preparation and bonding (see Technical Note
560A).
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the sunroof fixed window using the specific
support (this operation requires two people):
-Support: PARV 202,
-set of arch supports: APARV 200 ESP. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121153