roof RENAULT TWINGO RS 2009 2.G Trim And Upholstery Workshop Manual

71A-4
BODY INTERNAL TRIM
Headlining: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aPartially remove the front side door and tailgate
seals.aUnclip the trim piece (1) from the sun visor shutter
cross member mounting.
aRemove:
-the finishing seal (2) from the sunroof
-the sunroof switch plate (see Sunroof switch: Re-
moval - Refitting) (MR 411, 87D, Electric window
winders - Sunroof).
aRemove:
-the interior lights (see Interior light: Removal -
Refitting) (MR 411, 81B, Interior lights),
-the sun visors (see Sun visor: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the windscreen pillar trims (see 71A, Body inter-
nal trim, Windscreen pillar trim: Removal - Re-
fitting, page 71A-9) ,
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) (MR 412, 76A, Rear seat frame
and runners),
-the rear parcel shelf side trim panels (see 71A,
Body internal trim, Rear parcel shelf side trim:
Removal - Refitting, page 71A-15) ,
-the rear panel trims (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) , Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
OPENING ROOF
121712

71A-5
BODY INTERNAL TRIM
Headlining: Removal - Refitting
71A
-the B-pillar upper trims (see 71A, Body internal
trim, B-pillar upper trim: Removal - Refitting,
page 71A-10) ,
-the rear quarter panel trims (see 71A, Body inter-
nal trim, Quarter panel trim: Removal - Refit-
ting, page 71A-12) .
aDisconnect the interior light and sunroof connectors
(3) (depending on equipment level).
aDetach the interior light and sunroof wiring harnes-
ses (depending on equipment level).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the clips (4) .aRemove the headlining.
a
aRemove the headlining (this operation requires two
people).
REFITTING
I - REFITTING PREPARATION OPERATION
aLevel off any residual cement beading on the roof.
aCarefully remove any residual cement beading from
the headlining.
II - REFITTING OPERATION FOR PART
CONCERNED
aApply adhesive to the headlining (part no. 77 11 218
570).
aBond the headlining (this operation requires two
people).
121713
121306
121307
OPENING ROOF
Note:
The headlining is held in place with velcro strips,
tak e care not to damage them during the removal
operation.
The headlining must be handled with care after it
has been removed, cutting the sunroof weakens
the side edges.

71A-6
BODY INTERNAL TRIM
Headlining: Removal - Refitting
71A
aRefit the headlining (this operation requires two peo-
ple).
aRefit clips (4) .
III - FINAL OPERATION.
aRefit the interior light and sunroof wiring harnesses
(depending on equipment level).
aConnect the interior light and sunroof connectors (3)
(depending on equipment level).
aRefit:
-the interior lights (see Interior light: Removal -
Refitting) (MR 411, 81B, Interior lights),
-the sun visors (see Sun visor: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the windscreen pillar trims (see 71A, Body inter-
nal trim, Windscreen pillar trim: Removal - Re-
fitting, page 71A-9) ,
-the rear quarter panel trims (see 71A, Body inter-
nal trim, Quarter panel trim: Removal - Refit-
ting, page 71A-12) .
-the B-pillar upper trims (see 71A, Body internal
trim, B-pillar upper trim: Removal - Refitting,
page 71A-10) ,
-the rear panel trims (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the rear parcel shelf side trim panels (see 71A,
Body internal trim, Rear parcel shelf side trim:
Removal - Refitting, page 71A-15) ,
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) (MR 412, 76A, Rear seat frame
and runners),aRefit:
-the sunroof switch plate (see Sunroof switch: Re-
moval - Refitting) (MR 411, 87D, Electric window
winders - Sunroof),
-the sunroof finishing seal (2) .
aFit the sun visor headlining cross member mounting
trim piece (1) .
aRefit the front side door and tailgate seals.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners). OPENING ROOF
OPENING ROOF