SATURN VUE HYBRID 2007 Owners Manual

✍NOTES
141
ProCarManuals.com

Instrument Panel Overview
142
ProCarManuals.com

The main components of the instrument panel are the following:
A. Air Outlets. SeeClimate Control System on
page 156.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 145.
C. Cruise Control Buttons. SeeCruise Control
on page 148.
D. Horn. SeeHorn on page 144.
E. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 162.
F. Audio Steering Wheel Controls. SeeAudio
Steering Wheel Controls on page 227.
G. Windshield Wiper Lever. SeeWindshield
Wipers on page 146.
H. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 153.
I. Hazard Warning Flasher Button. SeeHazard
Warning Flashers on page 144.
J. Passenger Air Bag Status Indicator. See
Passenger Airbag Status Indicator on page 166.K. Traction Control System Button. SeeTraction
Control System (TCS) on page 240.
L. Audio System. SeeAudio System(s) on
page 184.
M. Hood Release. SeeHood Release on page 295.
N. Tilt Wheel Lever. SeeTilt Wheel on page 144.
O. Power Mirror Control. SeeOutside Power
Mirrors on page 130.
P. Power Window Switches. SeePower Windows
on page 108.
Q. Automatic Transaxle Shift Lever. SeeAutomatic
Transaxle Operation on page 118.
R. Heated Seats Buttons. SeeHeated Seats on
page 11.
S. Climate Control. SeeClimate Control System
on page 156.
T. Glove Box. SeeGlove Box on page 134.
143
ProCarManuals.com

Hazard Warning Flashers
The hazard warning ashers let you warn the
police and others that you have a problem.
The front and rear turn signal lamps will ash on
and off.
The hazard warning
asher button is located
in the center of the
instrument panel.
The hazard warning ashers work no matter what
position the key is in, and even if the key is not
in the ignition switch.
Press the button to make the front and rear turn
signal lamps ash on and off. Press the button
again to turn the ashers off.
While the hazard warning ashers are on, the turn
signals do not work.
Horn
Press near or on the horn symbols on your
steering wheel pad to sound the horn.
Tilt Wheel
Your vehicle has a tilt wheel which allows you to
adjust the steering wheel before you drive. You can
raise it to the highest level to give your legs more
room when you exit and enter the vehicle.
The lever that allows
you to tilt the steering
wheel is located on
the left side of the
steering column.
To tilt the wheel, hold the wheel and push the
lever down. Then, move the wheel to a
comfortable position and pull the lever up rmly
to lock the column in place.
144
ProCarManuals.com

Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane-Change Signals. SeeTurn
and Lane-Change Signals on page 145.
OExterior Lamp Control. SeeHeadlamps on
page 151.
2Headlamp High/Low-Beam Changer.
SeeHeadlamp High/Low-Beam Changer
on page 146.
Flash-to-Pass Feature. SeeFlash-to-Pass on
page 146.
AUTOAutomatic Headlamps. SeeAutomatic
Headlamp System on page 153.
Turn and Lane-Change Signals
The turn signal has one upward (for right) and
one downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is nished, the lever will
return automatically.
An arrow on the
instrument panel cluster
will ash in the
direction of the turn or
lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to ash. Hold it there until you
complete the lane change. The lever will return
by itself when you release it.
As you signal a turn or a lane change, if the
arrows ash rapidly, a signal bulb may be burned
out and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you
signal a turn, check the fuse, seeFuses and Circuit
Breakers on page 380and for burned-out bulbs.
145
ProCarManuals.com

Headlamp High/Low-Beam Changer
To change the headlamps from low beam to
high or high beam to low, pull the turn signal lever
all the way towards you. Then release it.
When the high beams
are on, this light on the
instrument panel
cluster will also be on.
Flash-to-Pass
This feature lets you use your high-beam
headlamps to signal a driver in front of you that
you want to pass.
To ash the high beams from low beam, pull the
turn signal/multifunction lever all the way
towards you. Then release it.
Windshield Wipers
Be sure to clear ice and snow from the wiper
blades before using them. If the wiper blades are
frozen to the windshield, gently loosen or thaw
them. If the blades do become damaged, install
new blades or blade inserts. SeeWindshield Wiper
Blade Replacement on page 338.
Heavy snow or ice can overload the wiper motor.
A circuit breaker will stop the motor until it cools
down. Clear away snow or ice to prevent an
overload.
United States
146
ProCarManuals.com

The lever on the right side of the steering column
operates the windshield wipers. Push up or
pull down on the lever to place it in one of the
following positions.
MIST or
8(Mist):Pull the lever down and
release it for a single wiping cycle. The lever will
return to its original position. For more cycles, hold
the lever down before releasing it.
OFF or
9(Off):Move the lever to this position
to turn off the wipers.
INT or
&(Intermittent):Move the lever to this
position to set a delay between wipes. To set
for a shorter or longer delay between wipes,turn the band with the arrow pointing to the
numbers (1, 2, or 3). Select 3 for the most frequent
movement; select 1 for the least frequent.
LO or
OO(Low):Move the lever to this position
for slow, steady wiping cycles.
HI or
OOOO(High):Move the lever to this
position for rapid wiping cycles.
Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
Pull the windshield wiper lever toward you to
operate the windshield wipers. Washer uid will
squirt onto the windshield and the wipers will
run for a few cycles to clear the windshield.
For more wash cycles, pull the lever toward you
and hold it there.
Canada
147
ProCarManuals.com

Rear Window Wiper/Washer
The band on the wiper lever with the smaller
arrow operates the rear wiper/washer.
9(Off):Turn the band to this position to turn off
the rear wiper.
Z(Rear Wiper):Turn the band with the smaller
arrow to this position to turn on the rear wiper.
To set for a shorter or longer delay between wipes,
turn the other band with the larger arrow pointing
to the numbers (1, 2, or 3). Select 3 for the
most frequent movement; select 1 for the least
frequent. The band with the arrow pointing to the
numbers (1, 2, or 3) will affect both the front
and rear wipers if they are on at the same time.
Y(Wash):Turn and hold the band in this position
to spray washer uid on the rear window.
The rear wiper will also come on. Release the
band when enough uid has been sprayed on the
window. The rear wiper will run a few additional
times after you release it.
The rear window washer uses the same uid bottle
as the windshield washer. However, the rear
window washer will run out of uid before the
windshield washer. If you can wash your windshield
but not your rear window, check the uid level.
Cruise Control
With cruise control, you can maintain a speed of
about 25 mph (40 km/h) or more without
keeping your foot on the accelerator. This can
really help on long trips. Cruise control does not
work at speeds below 25 mph (40 km/h).
{CAUTION:
Cruise control can be dangerous where
you cannot drive safely at a steady speed.
So, do not use your cruise control on
winding roads or in heavy traffic.
Cruise control can be dangerous on
slippery roads. On such roads, fast
changes in tire traction can cause
excessive wheel slip, and you could lose
control. Do not use cruise control on
slippery roads.
148
ProCarManuals.com

Setting Cruise Control
{CAUTION:
If you leave your cruise control on when
you are not using cruise, you might hit a
button and go into cruise when you do
not want to. You could be startled and
even lose control. Keep the cruise control
switch off until you want to use cruise
control.
The cruise control
buttons are located on
the steering wheel.
J(On/Off):Press this button to turn the cruise
control system on and off. There is a indicator light
on the button that will come on when cruise
control is active.
RES+ (Resume):Press this button to resume a
set speed and to accelerate the speed.
SET−(Set):Press this button to set a speed and
to decrease the speed.
[(Cancel):Press this button to cancel cruise
control.
To set a speed do the following:
1. Press the on/off symbol to turn cruise control
on. The indicator light on the button will
come on.
2. Get to the speed you want.
3. Press the SET−button and release it.
4. Take your foot off the accelerator pedal.
When the brakes are applied, the cruise control
shuts off.
149
ProCarManuals.com

Resuming a Set Speed
Suppose you set your cruise control at a desired
speed and then you apply the brakes. This will
disengage the cruise control. The indicator light on
the cruise control button will go out when the
cruise is no longer engaged. To return to the
previously set speed, press the RES+ button
briey when the vehicle has reached a speed of
about 25 mph (40 km/h) or more.
This will take you back up to your previously
selected speed and stay there.
Increasing Speed While Using Cruise
Control
There are two ways to go to a higher speed.
Disengage the cruise control, but do not
turn it off.
If the cruise control system is already
engaged, press the RES+ button. Hold it there
until you get up to the speed you want, and
then release the button. To increase your
speed in very small amounts, press the
RES+ button briey and then release it.
Each time you do this, the vehicle will go
about 1 mph (1.6 km/h) faster.
Reducing Speed While Using Cruise
Control
If the cruise control system is already engaged,
Push and hold the SET−button until you reach
the lower speed you want, then release it.
To slow down in very small amounts, push the
SET−button briey. Each time you do this, you
will go about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, the
vehicle will slow down to the cruise control speed
you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills
depends upon your speed, load, and the
steepness of the hills. When going up steep hills,
you may have to step on the accelerator pedal
to maintain the vehicle’s speed. When going
downhill, you may have to brake or shift to a lower
gear to keep the vehicle’s speed down. Of
course, applying the brakes ends cruise control.
Many drivers nd this to be too much trouble
and do not use cruise control on steep hills.
150
ProCarManuals.com