lock Seat Alhambra 2005 Workshop Manual

158Refuelling
C
Ca
au
ut
ti
io
on
n
On vehicles with a catalytic converter, never drive until the fueltank is
completely empty. The irregular fuel supply can cause misfiring. This allows
unburnt fuel into the exhaust system, which can cause overheating and
damage to the catalyst.
K
Releasing tank flap manually
If the central locking system should fail, the flap can be released
manually:
• Open tailgate and – if fitted – fold back the right luggage
compartment trim from side panel.
• Then push the locking rod in front of the white diaphragm
housing backward slightly in direction of arrow
⇒fig. 150.K
P
Pe
et
tr
ro
ol
l
In the chapter “Technical Data” and on the inside of the tank flap
you will find information on the correct octane rating for your
engine.
K
General notes
•Unleaded petrol must comply with DIN EN1)228 and leaded
petrol with DIN 51 600.
•If, in an emergency, the octane rating of the available petrol is
lower than that required by the engine, only drive with medium
engine speeds and low engine loading. H Hi
ig
gh
h een
ng
gi
in
ne
e llo
oa
ad
di
in
ng
g wwi
it
th
h
f fu
ul
ll
l tth
hr
ro
ot
tt
tl
le
e oor
r hhi
ig
gh
h rre
ev
vs
s cca
an
n cca
au
us
se
e een
ng
gi
in
ne
e dda
am
ma
ag
ge
e.
.
Fill tank with
petrol of the correct octane rating as soon as possible.
•Fuel with a higher octane rating than that required by the engine
can be used without limitation. There are, however, no advantages
regarding output and consumption.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
Even one tankful of leaded petrol will detract from the efficiency ofthe
catalytic converter.
N No
ot
te
e
See chapter “Filling the tank”.K
1)European norm
B7M-093CFig. 150

Servobrake
Anti-locking brake system*
The ABS plays a major part in increasing the active safety of the
vehicle. The big advantage when compared with a conventional
brake system is that even when braking hard on a slippery road
surface the best possible steerability is retained for the road
condition because the wheels do not lock. S St
te
ee
er
ri
in
ng
g cco
on
nt
tr
ro
ol
l iis
s
t th
he
er
re
ef
fo
or
re
e mma
ai
in
nt
ta
ai
in
ne
ed
d,
, ggi
iv
vi
in
ng
g tth
he
e bbe
es
st
t ddr
ri
iv
vi
in
ng
g sst
ta
ab
bi
il
li
it
ty
y ppo
os
ss
si
ib
bl
le
e.
.
However, one must not expect the ABS system to shorten the
braking distance under all conditions. When driving on gravel or on
fresh snow covering a slippery surface, i.e. when one should be
driving very slowly and carefully, the stopping distance may even
be slightly longer.
Modifications to the vehicle (i.e.: the brake system or the drive-
train) may affect the antilock system operation*, for this reason we
advise you to bear in mind the instructions in the "Accessories"
chapter.H Ho
ow
w tth
he
e AAB
BS
S*
* ssy
ys
st
te
em
m wwo
or
rk
ks
s
An automatic check is made when a speed of approx. 6 km/h is
reached. When this happens a pumping noise can be heard.
When the turning speed of a wheel reaches a level which is too low
for the vehicle speed and it tends to lock, the brake pressure to
this wheel is reduced. On the front axle the brake pressure is
regulated for each wheel individually, whereas on the rear axle, the
pressure is regulated for both wheels at the same time. As a result
the braking effect is the same for both rear wheels and the driving
stability is retained as far as possible. T Th
hi
is
s rre
eg
gu
ul
la
at
ti
in
ng
g ppr
ro
oc
ce
es
ss
s
m ma
ak
ke
es
s iit
ts
se
el
lf
f kkn
no
ow
wn
n bby
y mmo
ov
ve
em
me
en
nt
t oof
f tth
he
e bbr
ra
ak
ke
e ppe
ed
da
al
l aan
nd
d iis
s
a ac
cc
co
om
mp
pa
an
ni
ie
ed
d bby
y nno
oi
is
se
es
s.
.
This is done deliberately as a warning to
the driver that a wheel or the wheels are in the locking range. S So
o
t th
ha
at
t tth
he
e AAB
BS
S cca
an
n rre
eg
gu
ul
la
at
te
e eef
ff
fe
ec
ct
ti
iv
ve
el
ly
y iin
n tth
hi
is
s rra
an
ng
ge
e tth
he
e bbr
ra
ak
ke
e ppe
ed
da
al
l
m mu
us
st
t rre
em
ma
ai
in
n dde
ep
pr
re
es
ss
se
ed
d –– oon
n nno
o aac
cc
co
ou
un
nt
t ssh
ho
ou
ul
ld
d iit
t bbe
e ppu
um
mp
pe
ed
d!
!
If a defect occurs on the ABS it is indicated by one or two warning
lamps.
K
162Intelligent technology
T
Th
he
e sse
er
rv
vo
o iis
s oop
pe
er
ra
at
te
ed
d bby
y aa vva
ac
cu
uu
um
m wwh
hi
ic
ch
h iis
s oon
nl
ly
y gge
en
ne
er
ra
at
te
ed
d wwh
he
en
n tth
he
e
e en
ng
gi
in
ne
e iis
s rru
un
nn
ni
in
ng
g.
. FFo
or
r tth
hi
is
s rre
ea
as
so
on
n tth
he
e vve
eh
hi
ic
cl
le
e ssh
ho
ou
ul
ld
d nno
ot
t bbe
e aal
ll
lo
ow
we
ed
d tto
o rro
ol
ll
l
w wi
it
th
h tth
he
e een
ng
gi
in
ne
e ssw
wi
it
tc
ch
he
ed
d oof
ff
f.
.
W Wh
he
en
n tth
he
e bbr
ra
ak
ke
e sse
er
rv
vo
o iis
s nno
ot
t wwo
or
rk
ki
in
ng
g bbe
ec
ca
au
us
se
e,
, ffo
or
r eex
xa
am
mp
pl
le
e,
, tth
he
e vve
eh
hi
ic
cl
le
e iis
s
b be
ei
in
ng
g tto
ow
we
ed
d oor
r aa dde
ef
fe
ec
ct
t hha
as
s ooc
cc
cu
ur
rr
re
ed
d oon
n tth
he
e bbr
ra
ak
ke
e sse
er
rv
vo
o iit
ts
se
el
lf
f,
, tth
he
e bbr
ra
ak
ke
e
p pe
ed
da
al
l mmu
us
st
t bbe
e ppr
re
es
ss
se
ed
d cco
on
ns
si
id
de
er
ra
ab
bl
ly
y hha
ar
rd
de
er
r tto
o cco
om
mp
pe
en
ns
sa
at
te
e ffo
or
r tth
he
e aab
bs
se
en
nc
ce
e
o of
f sse
er
rv
vo
o aas
ss
si
is
st
ta
an
nc
ce
e.
.
K
W WA
AR
RN
NI
IN
NG
G
H Ho
ow
we
ev
ve
er
r tth
he
e AAB
BS
S ssy
ys
st
te
em
m cca
an
nn
no
ot
t oov
ve
er
rc
co
om
me
e tth
he
e pph
hy
ys
si
ic
ca
al
l lli
im
mi
it
ts
s.
. TTh
hi
is
s mmu
us
st
t bbe
e
b bo
or
rn
ne
e iin
n mmi
in
nd
d ppa
ar
rt
ti
ic
cu
ul
la
ar
rl
ly
y oon
n ssl
li
ip
pp
pe
er
ry
y oor
r wwe
et
t rro
oa
ad
ds
s.
. WWh
he
en
n tth
he
e AAB
BS
S cco
om
me
es
s
i in
nt
to
o tth
he
e cco
on
nt
tr
ro
ol
l rra
an
ng
ge
e tth
he
e ssp
pe
ee
ed
d mmu
us
st
t iim
mm
me
ed
di
ia
at
te
el
ly
y bbe
e aad
da
ap
pt
te
ed
d tto
o tth
he
e rro
oa
ad
d
a an
nd
d ttr
ra
af
ff
fi
ic
c cco
on
nd
di
it
ti
io
on
ns
s.
. TTh
he
e iin
nc
cr
re
ea
as
se
ed
d aam
mo
ou
un
nt
t oof
f ssa
af
fe
et
ty
y aav
va
ai
il
la
ab
bl
le
e mmu
us
st
t nno
ot
t
t te
em
mp
pt
t oon
ne
e iin
nt
to
o tta
ak
ki
in
ng
g rri
is
sk
ks
s.
.
W
WA
AR
RN
NI
IN
NG
G

164Intelligent technology
W
Wh
he
ee
el
ls
sp
pi
in
n cco
on
nt
tr
ro
ol
l ((T
TC
CS
S)
)
In vehicles with front wheel traction, the TCS lowers the engine
power to stop the wheel spinning when you accelerate. This feature
works at any speed in combination with the ABS. If there is an ABS
breakdown, the TCS stops working.
Vehicles fitted with TCS are also fitted with an electronic differential
lock (EDL).
The EDL makes it much easier, or even possible, to pull away,
accelerate and climb steep gradiants in unfavourable conditions.
The EDL works fully automatically – the driver does not need to do
anything at all.
It uses the ABS sensors to monitor the speed of the driving wheels.
Up to a speed of about 80 km/h (50 mph), a difference in speed of
the drive wheels of approximately 100 rpm caused by a slippery
road surface on o on
ne
e ssi
id
de
e
is balanced out by slowing down the
wheel which is slipping and thereby applying more driving force to
the other drive wheel through the differential.
T Th
hi
is
s cco
on
nt
tr
ro
ol
l ppr
ro
oc
ce
ed
du
ur
re
e cca
an
n bbe
e dde
et
te
ec
ct
te
ed
d bby
y tth
he
e sso
ou
un
nd
d iit
t mma
ak
ke
es
s.
.
I In
n oor
rd
de
er
r tto
o oob
bt
ta
ai
in
n tth
he
e bbe
es
st
t ppo
os
ss
si
ib
bl
le
e eef
ff
fe
ec
ct
t ffr
ro
om
m tth
he
e EED
DL
L,
, aal
lw
wa
ay
ys
s uus
se
e
t th
he
e ccl
lu
ut
tc
ch
h aan
nd
d aac
cc
ce
el
le
er
ra
at
to
or
r ppe
ed
da
al
ls
s aac
cc
co
or
rd
di
in
ng
g tto
o tth
he
e rro
oa
ad
d
c co
on
nd
di
it
ti
io
on
ns
s.
.To ensure that the brake disc of the braked wheel does not
overheat, the EDL will automatically switch itself off if excessive
demands are placed on it. The vehicle remains operational and has
the same characteristics as a vehicle without EDL. For this reason,
the switching off of the EDL is not noticed.
As soon as the brakes have cooled off, the EDL will switch itself
back on again.
If the ABS warning lamp lights up there may be a fault present in
the EDL. Take the vehicle to a Technical Service Centre as soon as
possible!
The TCS connects automatically once the engine is started. If
necessary, it can be connected or disconnected by pressing shortly
the button located on the central console.
When the TCS is switched off a pilot light comes on.
You should normally always have the TCS on. Only in exceptional
circumstances when you want the wheels to spin should you
switch it off. For instance:
– When you are using snow chains.
– When driving in deep snow or on a soft surface.
– When the car is stuck, to “rock” it out, and

W Wh
he
en
n aac
cc
ce
el
le
er
ra
at
ti
in
ng
g oon
n aa ssl
li
ip
pp
pe
er
ry
y rro
oa
ad
d ssu
ur
rf
fa
ac
ce
e,
, ee.
.g
g.
. oon
n iic
ce
e oor
r ssn
no
ow
w,
, uus
se
e tth
he
e
a ac
cc
ce
el
le
er
ra
at
to
or
r ppe
ed
da
al
l cca
ar
re
ef
fu
ul
ll
ly
y.
. TTh
he
e wwh
he
ee
el
ls
s cca
an
n ssp
pi
in
n,
, eev
ve
en
n wwi
it
th
h EED
DL
L,
, aan
nd
d tth
hu
us
s
i im
mp
pa
ai
ir
r ddr
ri
iv
vi
in
ng
g sst
ta
ab
bi
il
li
it
ty
y.
.
W
WA
AR
RN
NI
IN
NG
G
T Th
he
e sst
ty
yl
le
e oof
f ddr
ri
iv
vi
in
ng
g mmu
us
st
t aal
lw
wa
ay
ys
s bbe
e aad
da
ap
pt
te
ed
d tto
o ssu
ui
it
t tth
he
e rro
oa
ad
d ssu
ur
rf
fa
ac
ce
e aan
nd
d
t tr
ra
af
ff
fi
ic
c cco
on
nd
di
it
ti
io
on
ns
s.
. TTh
he
e iin
nc
cr
re
ea
as
se
ed
d ssa
af
fe
et
ty
y oof
ff
fe
er
re
ed
d bby
y tth
he
e EED
DL
L ssh
ho
ou
ul
ld
d nno
ot
t
e en
nc
co
ou
ur
ra
ag
ge
e oon
ne
e tto
o tta
ak
ke
e uun
nn
ne
ec
ce
es
ss
sa
ar
ry
y rri
is
sk
ks
s.
.
W
WA
AR
RN
NI
IN
NG
G

175 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
• As driving stability of vehicle and trailer decreaseswhen the
speed increases do not drive at the maximum permissible top
speed in unfavourable road, weather or wind conditions –
particularly when going downhill.
In any case the speed must be reduced as soon as the trailer
shows the slightest sign of snaking. On no account try to stop the
snaking by accelerating.
• • FFo
or
r ssa
af
fe
et
ty
y rre
ea
as
so
on
ns
s oon
ne
e ssh
ho
ou
ul
ld
d nno
ot
t ddr
ri
iv
ve
e ffa
as
st
te
er
r tth
ha
an
n 880
0 kkm
m/
/h
h
( (5
50
0 mmp
ph
h)
).
. TTh
hi
is
s aal
ls
so
o aap
pp
pl
li
ie
es
s iin
n cco
ou
un
nt
tr
ri
ie
es
s wwh
he
er
re
e hhi
ig
gh
he
er
r ssp
pe
ee
ed
ds
s aar
re
e
p pe
er
rm
mi
it
tt
te
ed
d.
.
• Always brake in good time. If the trailer has an overrun brake,
apply the brakes gently at first then firmly. This will avoid the
jerking caused by the trailer wheels locking.
Change down before going down a steep hill so thatthe engine
can act as a brake.
• When a long climb in a low gear with extremely high engine revs
must be negotiated at exceptionally high ambient temperatures
the coolant temperature gauge must be observed. When the gauge
needle moves to the right end of the scale, the road speed must be
reduced immediately.
• The cooling effect of the radiator fan cannot be increased by
changing down, because the speed of the fan is not dependent on
the engine speed. One should therefore not change down even
when towing a trailer as long as the engine can cope without the
vehicle speed dropping too much.
K
General notes
• • DDu
ur
ri
in
ng
g tth
he
e rru
un
nn
ni
in
ng
g iin
n ppe
er
ri
io
od
d yyo
ou
u ssh
ho
ou
ul
ld
d aav
vo
oi
id
d tto
ow
wi
in
ng
g aa ttr
ra
ai
il
le
er
r iif
f
p po
os
ss
si
ib
bl
le
e.
.
• • IIt
t iis
s aad
dv
vi
is
sa
ab
bl
le
e tto
o hha
av
ve
e tth
he
e vve
eh
hi
ic
cl
le
e sse
er
rv
vi
ic
ce
ed
d bbe
et
tw
we
ee
en
n tth
he
e
I In
ns
sp
pe
ec
ct
ti
io
on
n iin
nt
te
er
rv
va
al
ls
s iif
f iit
t iis
s uus
se
ed
d ffr
re
eq
qu
ue
en
nt
tl
ly
y ffo
or
r tto
ow
wi
in
ng
g aa ttr
ra
ai
il
le
er
r.
.
• The trailer and drawbar load figures on the data plate of the
towing bracket are for test certification only. The correct figuresfor
the vehicle, which may be lower than the above figures, are given
in the vehicle documents and in this manual.
• When using the towing device the car’s empty weight is reduced,
and as a result its effective load is decreased.
• Observe all statutory requirements regarding the use of a
trailer.
K

178Care and maintenance
N
No
ot
te
e
• Before going through the car wash, apart from the usual precautions
(closing windows and sliding roof).
You do not need to remove the Original roof aerial.
• If there are special fittings on the vehicle – e.g. spoilers, roof rack, two-
way radio aerial – it is best to speak to the car wash operator.
K
Washing the vehicle by hand
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
In the interests of environmental protection the vehicle should only be
washed in specially provided wash bays. In some districts, washing cars
elsewhere may even be forbidden.
First soften the dirt with plenty of water and rinse off as well as
possible. Then clean the car w wi
it
th
h aa sso
of
ft
t ssp
po
on
ng
ge
e,
, ggl
lo
ov
ve
e oor
r bbr
ru
us
sh
h
starting on the roof and going from top to bottom u us
si
in
ng
g oon
nl
ly
y ssl
li
ig
gh
ht
t
p pr
re
es
ss
su
ur
re
e ees
sp
pe
ec
ci
ia
al
ll
ly
y wwh
he
en
n ccl
le
ea
an
ni
in
ng
g tth
he
e hhe
ea
ad
dl
li
ig
gh
ht
t aar
re
ea
a.
.
Paint
shampoo, preferably with a neutral pH, should only be used for
very persistent dirt. Rinse the sponge or glove out thoroughly at
short intervals.
Wheels and sill panels should be cleaned last, using a different
sponge if possible.
After cleaning the vehicle, rinse thoroughly with water and leather
it off.N No
ot
te
e
•The vehicle should not be washed in strong sunshine.
•If the vehicle is rinsed with a hose, do not direct the jet of water
at the lock cylinders and the door/boot lid/tailgate shut lines –
they can freeze up in the winter.
K
Washing vehicle with high pressure cleaner
• The operating instructions for the high pressure cleaner must be
followed closely – particularly with regard to pressure and working
distance.
• Do not use a concentrated jet.
• The water temperature must not be above 60°C.
Conservation
Regular application of protection products protects the vehicle
paintwork to a large extent against the environmental influences
listed under “Washing” on the previous page and even against
light mechanical damage.
At the latest when water on the clean paint does not form small
drops and roll off, the vehicle should be protected by applying a
coat of good hard wax. Even when a wax solution is used regularly
T Ty
yr
re
es
s mmu
us
st
t nne
ev
ve
er
r bbe
e ccl
le
ea
an
ne
ed
d wwi
it
th
h aa cco
on
nc
ce
en
nt
tr
ra
at
te
ed
d jje
et
t!
! EEv
ve
en
n aat
t aa rre
el
la
at
ti
iv
ve
el
ly
y
l la
ar
rg
ge
e wwo
or
rk
ki
in
ng
g ddi
is
st
ta
an
nc
ce
e aan
nd
d aa vve
er
ry
y ssh
ho
or
rt
t ssp
pr
ra
ay
yi
in
ng
g tti
im
me
e,
, dda
am
ma
ag
ge
e cca
an
n
o oc
cc
cu
ur
r.
.
K
W WA
AR
RN
NI
IN
NG
G


179 Care and maintenance
Safety FirstControls and equipment Tips and Maintenance Technical Data
in the washing water it is advisable to protect the paint with a coat
of hard wax at least twice a year.
K
Polishing
Should only be done if paint has lost its shine and gloss cannot be
brought back with wax. If the polish used does not contain
preservative compounds, the paint must be waxed afterwards.
N No
ot
te
e
Matt painted and plastic parts should not be treated with polish or hard
wax.K
Paint damage
Small marks in the paint such as scratchesor stone damage
should be touched up immediately with paint before the metal
starts to rust.
However, should rust be found at any time it must be removed
thoroughly and then the area treated first with an anti-corrosion
primer and then the correct paint applied.
The number of the original vehicle paint is given on the data
sticker which is inside the boot in the spare wheel housing.
K
Windows
Remove snow and ice from windows and mirrors with a plastic
scraper only. To avoid scratches due to dirt on the glass, the
scraper should only be pushed in one direction and not moved to
and fro.
Traces of rubber, oil, wax
1), grease or silicone can be removed with
a window cleaning solution or a silicone remover.
The windows should also be cleaned on the inside at regular
intervals.
Do not dry the windows with the leather used for the paintwork
because traces of paint cleaner will cause streaks to appear on the
glass, which will hinder vision.
To avoid damaging the heating element wires in the rear window
do not put stickers over the wires on the inside.
K
Door, boot and window seals
The weatherstrips will remain flexible and last longer if they are
rubbed lightly with a rubber protective compound from time to
time. This will also stop the weatherstrips from freezing on in
winter.
K
Door lock cylinder
You should only use an appropriate spray, which has lubricating
and anti-corrosive qualities, to de-ice the lock cylinder.
K
1)This wax residue can only be removed with a special cleaner. Your Technical Service
Centre will provide you with more detailed information.

181 Care and maintenance
Safety FirstControls and equipment Tips and Maintenance Technical Data
Steel wheels
The wheels and the wheel trims should be cleaned thoroughly at
regular intervals when the vehicle is being washed. This will
prevent brake dust, dirt and road salt from accumulating on the
wheel. Persistent ingrained brake dust can be removed with an
industrial grime remover. Paint damage should be repaired before
rust can form.
K
Alloy wheels*
In order to maintain the smart appearance of alloy wheels for a
long period, regular care is necessary. In particular, salt and brake
pad dust must be washed off thoroughly at least every two weeks
otherwise the surface of the alloy will be damaged. After being
washed, the wheels should be treated with an acid-free cleaner for
alloy wheels. About every three months it is necessary to give
wheels a good rubbing with hard wax. Paint polish or other
abrasive solutions must not be used. If the protective paint coat
has been damaged, e.g. by stone impact, the damaged spots
should be dealt with as soon as possible.
Cleaning and anti-corrosion treatment of engine
compartment
The leaves, blossoms etc. which drop into the water box
(underneath the engine bonnet in front of the windscreen) should
be cleaned out occasionally. This will prevent the water drain holes
from becoming blocked and – on vehicles without a dust and
pollen filter – foreign bodies entering the vehicle interior via the
heating and ventilation system.
The engine compartment and the outside surface of the power unit
are given anti-corrosion treatment at the factory.
In the winter when the vehicle is being driven frequently on salted
roads, good anti-corrosion treatment is very important. For this
reason the entire engine compartment and the plenum chamber
should be thoroughly cleaned before and after the salting period
and then preserved so that the salt cannot have a damaging effect.
T Th
he
e iig
gn
ni
it
ti
io
on
n mmu
us
st
t bbe
e ssw
wi
it
tc
ch
he
ed
d oof
ff
f bbe
ef
fo
or
re
e wwa
as
sh
hi
in
ng
g tth
he
e een
ng
gi
in
ne
e.
.
D Do
o nno
ot
t ppo
oi
in
nt
t tth
he
e wwa
at
te
er
r jje
et
t ddi
ir
re
ec
ct
tl
ly
y aat
t tth
he
e hhe
ea
ad
dl
li
ig
gh
ht
ts
s tto
o aav
vo
oi
id
d
d da
am
ma
ag
ge
e.
.
P
Pl
le
ea
as
se
e nno
ot
te
e wwh
he
en
n ccl
le
ea
an
ni
in
ng
g tth
he
e wwh
he
ee
el
ls
s tth
ha
at
t dda
am
mp
pn
ne
es
ss
s,
, iic
ce
e aan
nd
d ggr
ri
it
t cca
an
n
h ha
av
ve
e aa nne
eg
ga
at
ti
iv
ve
e eef
ff
fe
ec
ct
t oon
n tth
he
e bbr
ra
ak
ki
in
ng
g ppo
ow
we
er
r.
.
K
W WA
AR
RN
NI
IN
NG
G
•B Be
ef
fo
or
re
e wwo
or
rk
ki
in
ng
g iin
n tth
he
e een
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t,
, rre
ea
ad
d tth
he
e nno
ot
te
es
s iin
n tth
he
e
" "E
En
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t"
" cch
ha
ap
pt
te
er
r.
.
•F
Fo
or
r ssa
af
fe
et
ty
y rre
ea
as
so
on
ns
s ppu
ul
ll
l oou
ut
t iig
gn
ni
it
ti
io
on
n kke
ey
y bbe
ef
fo
or
re
e rre
ea
ac
ch
hi
in
ng
g iin
nt
to
o tth
he
e wwa
at
te
er
r
b bo
ox
x.
. OOt
th
he
er
rw
wi
is
se
e iif
f tth
he
e wwi
in
nd
ds
sc
cr
re
ee
en
n wwi
ip
pe
er
rs
s aar
re
e ssw
wi
it
tc
ch
he
ed
d oon
n uun
ni
in
nt
te
en
nt
ti
io
on
na
al
ll
ly
y
t th
he
e mmo
ov
ve
em
me
en
nt
t oof
f tth
he
e wwi
ip
pe
er
r lli
in
nk
k cco
ou
ul
ld
d cca
au
us
se
e iin
nj
ju
ur
ry
y.
.
W
WA
AR
RN
NI
IN
NG
G


183 Checking and refilling
Safety FirstControls and equipment Tips and Maintenance Technical Data
C
Ch
he
ec
ck
ki
in
ng
g aan
nd
d rre
ef
fi
il
ll
li
in
ng
g
E
En
ng
gi
in
ne
e bbo
on
nn
ne
et
t
Opening the bonnet
T
To
o rre
el
le
ea
as
se
e llo
oc
ck
k
, pull lever on left under instrument panel – the
bonnet springs up out of its lock.
N No
ot
te
e
Before opening the bonnet ensure that the wiper arms are not lifted off the
windscreen. Otherwise damage can occur to the paintwork.
T To
o oop
pe
en
n tth
he
e bbo
on
nn
ne
et
t
, lift slightly and press the safety catch in the
direction of the arrow
⇒fig. 156.
Fig. 155
Fig. 156

ALO-126
AL0-127

190Checking and refilling
C
Ca
au
ut
ti
io
on
n
• Only our G12+ (purple colour) should be used as an antifreeze additive.
Observe the notice on the container. The cooling liquid may be purchased in
Technical Services.
• The antifreeze additive G12+ can be mixed with other additives (G11 and
G12).
• The additive G12 (red colour) should never be mixed with G11.
K
Checking coolant level
The level can only be checked properly when the engine is not
running.
The coolant level must be between the
m ma
ax
xand m
mi
in
nmarks on the
expansion tank when engine is cold and can be slightly above the
m ma
ax
xmark when it is warm.K
Coolant losses
Coolant loss normally indicates leaks in the system. In this case
the cooling system should be checked by a Technical Service
Center without delay. It is not sufficient merely to add coolant.
In a sealed system losses can only occur if the boiling point of the
coolant is exceeded as a result of overheating, and coolant is
forced out of the system.
K
Topping up coolant
Switch engine off and let it cool down. Then cover expansion tank
cap with a cloth and turn cap carefully anti-clockwise and remove.
No other coolant may be used if
G G1
12
2+
+is not available. In this
case only water can be used and the correct mixture concentration
must be restored with the specified coolant additive (see previous
page) as soon as possible.
Fig. 160
N Ne
ev
ve
er
r oop
pe
en
n tth
he
e bbo
on
nn
ne
et
t iif
f yyo
ou
u cca
an
n sse
ee
e sst
te
ea
am
m oor
r cco
oo
ol
la
an
nt
t lle
ea
av
vi
in
ng
g tth
he
e een
ng
gi
in
ne
e
c co
om
mp
pa
ar
rt
tm
me
en
nt
t –– RRi
is
sk
k oof
f ssc
ca
al
ld
di
in
ng
g!
! WWa
ai
it
t uun
nt
ti
il
l nno
o mmo
or
re
e sst
te
ea
am
m oor
r cco
oo
ol
la
an
nt
t cca
an
n
b be
e sse
ee
en
n.
.
W
WA
AR
RN
NI
IN
NG
G
D Do
o nno
ot
t rre
em
mo
ov
ve
e eex
xp
pa
an
ns
si
io
on
n tta
an
nk
k cca
ap
p wwh
he
en
n een
ng
gi
in
ne
e iis
s hho
ot
t –– dda
an
ng
ge
er
r oof
f
s sc
ca
al
ld
di
in
ng
g:
:
S Sy
ys
st
te
em
m iis
s uun
nd
de
er
r ppr
re
es
ss
su
ur
re
e.
.
W
WA
AR
RN
NI
IN
NG
G

AL0-046

196Checking and refilling
• Check acid level of the battery⇒"Battery chapter". Depending
on the technique used while charging battery acid could
vaporize.
K
If the battery is disconnected and then reconnected...
P Pl
le
ea
as
se
e nno
ot
te
e tth
he
e wwa
ar
rn
ni
in
ng
gs
s ffr
ro
om
m tth
he
e ""E
En
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t"
" cch
ha
ap
pt
te
er
r
a an
nd
d ffo
ol
ll
lo
ow
wi
in
ng
g oon
ne
es
s,
, bbe
ef
fo
or
re
e uun
nd
de
er
rg
go
oi
in
ng
g aan
ny
y wwo
or
rk
k oon
n tth
he
e een
ng
gi
in
ne
e oor
r
e en
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t.
.
After d di
is
sc
co
on
nn
ne
ec
ct
ti
in
ng
g
or charging the battery you should:
To reset the clock
⇒"Instruments" chapter.
Switch on again the automatic opening and closing of the power
windows
⇒"Electrical powered windows" chapter.
Should you have problems with the starting or idling of a petrol
engine start engine as follows: switch on ignition for approximately
30 seconds and switch off again. Start engine.
K
Change battery
Our batteries have been developed to suit their location and have
built-in safety elements. Original SEAT batteries comply with all
maintenance, performance and safety requirements for your
vehicle.
We recommend using a battery that does not require maintenance.
P Pl
le
ea
as
se
e nno
ot
te
e tth
he
e wwa
ar
rn
ni
in
ng
gs
s ffr
ro
om
m tth
he
e ""E
En
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t"
" cch
ha
ap
pt
te
er
r
a an
nd
d ffo
ol
ll
lo
ow
wi
in
ng
g oon
ne
es
s,
, bbe
ef
fo
or
re
e uun
nd
de
er
rg
go
oi
in
ng
g aan
ny
y wwo
or
rk
k oon
n tth
he
e een
ng
gi
in
ne
e oor
r
e en
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t.
.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
Because of the problem of disposing of the old battery, the renewalshould
preferably done at a Technical Service Centre. Batteries contain, amongst
other things, sulphuric acid and lead and must on no account be putwith
normal household waste.
K