light Seat Alhambra 2010 Owners Manual

Driving 230
xWhen cleaning the sensors with high-pressure or steam cleaning equip-
ment, spray the sensors briefly at a distance of no less than 10 cm.
Note
Contact a specialist workshop with any system faults. SEAT recommends
visiting a qualified workshop.
Parking using the park assist system
Fig. 153 Gap detected: Engage the reverse gear to park (parallel or nose/tail to the
kerb).
Preparing to park
xThe Traction control system (TCS) must be turned on Ÿpage 210.
xParallel parking: press the button at speeds up to 50 km/h once.
When the function is enabled, the button Ÿfig. 152 will light up.
xPerpendicular parking: press the button at speeds up to 50 km/h
twice. When the function is enabled, the button Ÿfig. 152 will light up.
xIf necessary, press the button once more to change parking mode.
xApply the turn signal indicator for the side on which a gap is to be
detected for parking. The instrument panel displays the side corresponding
to the road.
Parking
xParking parallel to the road: Drive next to the gap at a speed of no more
than 40 km/h and at a distance of between 0.5 m and 2 m.
Fig. 152 Detailed view of
the centre console: button
to switch the park assist
system on manually.i
i
i

Driving 232
Note
The park assist can also be activated afterwards, if you pass close to a parallel
parking space at a maximum of 40 km an hour or close to be perpendicular
parking space at about 20 km an hour then press the button .
Note
The progress bar on the screen of the instrument panel shows a display of the
relative distance to be covered.
Note
When the Park Assist system is turning the steering wheel of the stopped
vehicle the symbol K is also displayed. Press on the brake pedal so that the
steering can turn with the vehicle at a standstill and thus reduce the number
of manoeuvres.
Note
A suitable parking space length is at least 1.1 m greater than the length of the
vehicle.
Note
If the results of the park assist system are not as good after changing the
wheels, the system must memorise the perimeter of the new wheels. This
process is performed automatically while the vehicle is in motion. To help this
process, turn slowly (at less than 20 km/h), e.g. in an empty car park.
Leaving a parking space using the Park Assist system
Driving off
xSwitch on the engine.
xPress button . When the function is enabled, the button Ÿpage 230,
fig. 152 will light up.
xApply the turn signal indicator for the side on which you want to leave the
parking space.
xSelect reverse gear.
xFollow the instructions given by the park assist system.
xWhen the next indication appears, release the steering wheel Ÿ in
“Parking using the park assist system” on page 230: The system will move
the steering wheel! Observe the surrounding area.
xObserve the surrounding area and accelerate carefully at a maximum of
up to 7 km/h.
xThe park assist system is only responsible for moving the steering wheel
during the manoeuvre. The driver applies the accelerator, the clutch, the
gears and the brake.
xWhen it is possible to leave the parking space, the Park Assist system will
stop. Take control of the steering and when traffic conditions permit, leave
the parking space.
Automatic stoppage of the manoeuvre
The park assist system stops the manoeuvre in the event of one of the
following:
xDriving faster than 7 km/h.
xThe driver moves the steering wheel.
xA sliding door is opened. To restart the manoeuvre, close the sliding door
and press the button again.
xThere is a system malfunction (system temporarily unavailable).
xThe TCS system is switched off or the TCS or ESP is working.
ii
i

Driving 234
Rear Assist system*
Introduction
The camera fitted to the tailgate helps drivers during parking or reversing
manoeuvres. The camera image and certain orientation points generated by
the system are indicated on the factory-fitted radio or navigation system
screen.
Two types of location point (modes) can be selected:
xMode 1: reverse parking perpendicular to the road (e.g. in a car park).
xMode 2: reverse parking parallel to the curb.
The mode can be changed by pressing the button on the radio or navigation
system screen. Only the mode to which the points can be changed will be
displayed.
Additional information and warnings:
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Use of the camera to calculate the distance from obstacles (people, vehi-
cles, etc.) is inaccurate and may cause accidents and severe injuries.
xThe camera lens expands and distorts the field of vision and displays
the objects on the screen in a different, vague manner.
xSome objects may not be displayed or may not be very clear (e.g. very
thin posts or fences), due to the resolution of the monitor or if the light is
dim.
xThe camera has blind spots in which obstacles and people are not regis-
tered.
xKeep the camera lens clean and clear of snow and ice. Do not cover it.
WARNING
The intelligent technology in the rear assist system cannot change the
limits imposed by the laws of physics and by the system itself. Careless or
uncontrolled use of the rear assist system may result in severe injuries and
accidents. The system is not a replacement for driver awareness.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
xAlways keep a close eye on the area around the vehicle and always look
towards where you are parking. The display shows the path of the rear end
of the vehicle using the current steering angle. The front of the vehicle
turns more in comparison with the rear.
xDo not be distracted from the traffic when looking at the screen.
xAlways observe the area around the vehicle, as the cameras do not
always detect children, animals or objects.
xThe system might not show all areas clearly.
xOnly use the rear assist system when the tailgate is completely closed.
Caution
xThe camera only displays 2D images on the screen. Due to the lack of
depth, it might be difficult or impossible to recognise protruding objects or
cracks in the road.
xThe cameras may not always be able to detect objects such as thin rails,
fences, posts and trees, etc. This could result in damage to your car.

Driving 240
Warning and control lamp
Fig. 158 Dash panel display: CCS status indications.
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Display
There are different versions of the cruise control system. In vehicles with the
multifunction display (MFI), the set speed is displayed on the instrument
panel screen.Status fig. 158:
CCS temporarily switched off. The set speed is displayed in small figures.
System error. Contact a specialist workshop.
CCS switched on. The speed memory is empty.
The CCS is switched on. The set speed is displayed in large figures.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
lights upPossible causeSolution
%
This cruise control system
maintains the set speed of
the vehicle.–
AA
AB
AC
AD

Driving 244
The programme is switched on if and do not light up on
the button. The set programme remains selected after the ignition is switched
off.
WARNING
The dynamic features are modified by adjusting the shock absorbers.
Dynamic chassis control must never lead to any kinds of risk.
xAlways try to adapt the speed of the vehicle and your style of driving to
the condition of the ground or the road and to weather and traffic condi-
tions.
Note
In the event of a fault in the dynamic chassis control, and will
flash on the button. Driving comfort may be affected during the fault. Have
the system checked by a specialist workshop.
./2-!,#/-&/2430/24
#/-&/2430/24

Driving247
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Elements of the tyre monitoring indicatorControl lamp
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
When the tyres are inflated at different pressures or at a pressure that is
too low then a tyre may the damaged resulting in a loss of control of the
vehicle and a serious or mortal accident.
xIf the indicator ~ lights, stop immediately and check the tyres.
xIf the tyres are inflated at different pressures or if a tyre pressure is too
low, this will increase tyre wear, negatively affecting vehicle stability and
increasing braking distances.
Tyre monitoring indicator with button.
See Ÿpage 248.
b Warning lamp ~ on the instrument panel.
b button on the centre console.
b Monitoring the tread of all tyres using ABS sensors (indirect measure-
ment).
b Adjustable medium and full-load tyre pressures.
b Button to update the system when the tyre pressure is changed.
~ SET
Lights
up or
flashes
Possible cause ŸSolution
~
The tyre pressure of a wheel
has dropped considerably in
relation to the pressure set by
the driver Ÿpage 248.
› Stop the vehicle! Reduce your
speed immediately! Stop the
vehicle safely as soon as possi-
ble. Avoid sudden manoeuvres
and braking!
Check all tyres and pressures.
Replace any damaged tyres.
~System malfunction.
Consult a specialist workshop if
the tyre pressure is correct and
the lamp remains lit after switch-
ing the ignition off and back on
again. Have the system checked
there.

Driving and the environment 252
Ecological driving
Introduction
Fuel consumption, environmental impact and engine, brake and tyre wear
depend largely on three factors:
xPersonal driving style.
xConditions of use (weather, road surface).
xTechnical requirements.
Savings of up to 25% in fuel consumption are possible with an appropriate
driving style and the adoption of certain simple tips.
WARNING
Always adapt your speed and the distance to the vehicles ahead in line
with visibility, weather conditions, the condition of the road and the traffic
situation.
Economic driving style
Changing gear early
General instructions: The highest gear is always the most economical gear.
As a guideline, for the majority of vehicles: At a speed of 30 km/h, drive in
third gear, at 40 km/h in fourth gear and at 50 km/h in fifth gear.
In addition, skipping gears when shifting up helps to save fuel, weather and
traffic conditions permitting.
Do not wait until the last moment before changing gear. Only use first gear
when you move off and change to second gear quickly. Avoid the kick-down
function in vehicles with automatic gearbox.Vehicles with a gear display help to achieve an economical driving style as
the display indicates the best moment to change gear.
Let the vehicle roll
If you take your foot off the accelerator, the fuel supply is stopped and
consumption is reduced.
Allow the vehicle to roll without accelerating, for example when approaching
a red traffic light. However, if the vehicle is rolling too slowly or the distance
is too long, the clutch pedal should be pressed to declutch. The engine will
then operate at idle speed.
If the vehicle is going to be at a standstill for a period of time, switch off the
engine; for example, while waiting at a level crossing. In vehicles which have
the Start-Stop function on, the engine switches off automatically when the
vehicle is not moving.
Think ahead and “flow” with the traffic
Frequent acceleration and braking considerably increase fuel consumption. If
you think ahead as you drive and keep a safe distance from the vehicle in
front, it is possible to slow down by simply lifting your foot off the accelerator.
This eliminates the need for constant braking and acceleration.
Calm and steady driving
Constancy is more important than speed: The more you drive at a constant
speed, the lower the fuel consumption.
When driving on the motorway, it is more efficient to drive at a constant and
more moderate speed than to be continuously accelerating and braking. As a
general rule, you will reach your destination just as quickly when you drive at
a constant speed.
The cruise control function helps you to achieve a constant style of driving.
Moderate use of additional electrical appliances
It is important to travel in comfort, but convenience systems should be used
in an ecological manner.

Driving and the environment253
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Some equipment, when connected, increase fuel consumption considerably,
for example:
xAir conditioning cooling system: If the air conditioning system is required
to cool to significantly lower temperatures than the true outside temperature,
it will require a large quantity of energy from the engine. Therefore, we recom-
mend that the selected temperature for the vehicle is not too different to the
outside temperature. It is a good idea to open all the windows of the car
before starting your journey, and to drive a short distance with all the
windows open to allow the vehicle to cool down slightly. Only then should
you close all the windows and switch on the air conditioning. Keep windows
closed when travelling at high speeds. Driving with the windows open
increases fuel consumption.
xSwitch off the seat heating when the seats have warmed up.
xSwitch off the heated rear window and the windscreen heating when the
windows have demisted and are free of ice.
xDo not leave the independent heating switched on when the vehicle is
moving Ÿpage 187.
Other factors which increase fuel consumption (examples):
xFault in engine management.
xDriving on hills.
xTrailer towing.
Saving fuel while driving
By adopting an economical driving style and anticipating the traffic situation
ahead, you can easily reduce fuel consumption by 10-15%.
A vehicle uses most fuel when accelerating. By anticipating the traffic situa-
tion ahead, you will brake and therefore accelerate less. Wherever possible,
let the car roll slowly to a stop, for instance when you can see that the next
traffic lights are red.
Avoid short journeys
Fuel consumption is much higher when the engine is cold, immediately after
it has been started. It takes a few kilometres of driving for the engine to warm
up and to normalise consumption.
The engine and catalytic converter need to reach their proper working
temperature in order to minimise fuel consumption and emissions. The
ambient temperature has a decisive influence.
fig. 162 shows the difference in consumption for the same journey at +20 °C
(+68 °F) and at -10 °C (+14 °F).
Fig. 162 Fuel consump-
tion in litres per 100 km at
different outside tempera-
tures.

Driving and the environment 254
Unnecessary short journeys should be avoided. Try to combine trips.
The vehicle uses more fuel in winter than in summer, even when other condi-
tions are the same.
“Warming” the engine is not only forbidden in some countries, but in practice
it is technically superfluous as it is a waste of fuel.
Adjusting type pressures.
Having the correct pressure in your tyres helps to reduce rolling resistance
and, as a result reduces fuel consumption. Increasing the tyre pressure
slightly (+ 0.2 bar / + 3 psi) can help to save fuel.
If you are prepared to accept a slight reduction in comfort, the tyres may be
filled to the pressures recommended for a fully-loaded vehicle. This is also
valid when driving alone without luggage.
When you buy new tyres, make sure they are optimised for minimum rolling
resistance.
Use low friction engine oil
The use of low viscosity totally synthetic oils, known as low friction engine oil,
help to reduce fuel consumption. Low friction engine oils reduce the resist-
ance caused by friction in the engine, they flow around the engine more
quickly and efficiently, particularly in cold starts. The effect is particularly
noticeable in vehicles frequently used for short journeys.
Always check the engine oil level and observe service intervals (engine oil
change intervals).
When purchasing engine oil, always observe legal requirements and ensure
that the oil is approved by SEAT.
Avoid carrying unnecessary loads
The lighter the vehicle, the more economical and ecological the driving style.
For example, an additional weight of 100 kg will increase fuel consumption
up to 0.3 l/100 km.
Remove any unnecessary objects or loads from the vehicle.Remove optional equipment and unnecessary accessories
The more aerodynamic the vehicle, the lower the fuel consumption. Optional
equipment and accessories (such as roof racks or bike carriers) reduce the
aerodynamic benefits of the vehicle.
Therefore, we recommend you remove all optional and unnecessary equip-
ment and racks, especially if you intend to drive at high speeds.

Driving and the environment255
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Engine management and exhaust gas
purification system
Introduction
Additional information and warnings:
xChanging gear Ÿpage 201
xRefuelling Ÿpage 293
xFuel Ÿpage 297
xEngine oil Ÿpage 309
xVehicle battery Ÿpage 318
xInformation stored in the control units Ÿpage 285
xTow-starting and towing away Ÿpage 375
WARNING
The components of the exhaust system reach very high temperatures. This
could cause a fire.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as dried grass).
xDo not apply additional underseal or anti-corrosion coatings to the
exhaust pipes, catalytic converter, heat shields or the diesel particulate
filter.
Warning lamps
lights upPossible causeSolution
%0#Fault in engine management
(Electronic Power Control).Take the vehicle to a qualified
workshop as soon as possible
and have the engine checked.
DPre-heating a diesel engine
before starting the engine.Ÿpage 195
BFault in catalytic converter.
You should reduce speed accord-
ingly. Drive carefully until you
reach the next qualified work-
shop. Have the engine checked
there.
¬Diesel particulate filter
blocked
Drive for 15 minutes in 4th gear
(manual gearbox), or in D (auto-
matic gearbox) at a minimum
speed of 70 km/h (45 mph).
Observe speed limits Ÿ.
If the warning lamp remains lit
up, take the vehicle to a quali-
fied workshop Ÿpage 256.
flashesPossible causeSolution
DFault in the engine manage-
ment (diesel engines).Take the vehicle to a qualified
workshop as soon as possible
and have the engine checked.
B
Combustion fault which could
damage the catalytic con-
verter.You should reduce speed accord-
ingly. Drive carefully until you
reach the next qualified work-
shop. Have the engine checked
there.