lock Seat Alhambra 2010 Owner's Manual

Trailer towing 264
Loading the trailer
Trailer weight / drawbar load
The trailer weight is the load that the vehicle can pull Ÿ. The drawbar load
is the vertical weight of the trailer hitch on the tow hitch ball Ÿpage 267.
The figures for trailer weights and draw bar weights given on the data plate of
the towing bracket are for values of this model only. The correct figures for
your specific vehicle, which may be lower than these figures for the tow hitch,
are given in the registration documents. The instructions in the official
vehicle documents take precedence.
For the sake of road safety, SEAT recommends using the maximum allowed
drawbar load. The handling of the combined vehicle and trailer will be poor if
the drawbar load is too low.
The drawbar load increases the weight on the rear axle, reducing the vehicle
carrying capacity.
Gross combination weight
This figure refers to the combined weight of the loaded vehicle and loaded
trailer.
Loading the trailer
The combined vehicle and trailer must be balanced. Use the maximum
drawbar load authorised and do not overload the front or the rear of the
trailer:
xDistribute loads in the trailer so that heavy objects are as near to the axle
as possible or even above it.
xCorrectly secure the trailer load.
Tyre pressure
Inflate the trailer tyres according to the manufacturer's instructions.
Inflate the towing vehicles tyres to the maximum Ÿpage 323.
WARNING
Exceeding the maximum authorised axle load, drawbar load or the gross
combination weight of the towing vehicle and trailer could cause a serious
accident with severe consequences.
xNever exceed the specifications.
xWith the actual load on the front and rear axles, the maximum axle load
should never be exceeded. The weight on the front and rear should never
exceed the gross vehicle weight.
WARNING
If the load moves, the stability and safety of the vehicle and trailer combi-
nation will be seriously affected and this could result in a serious accident.
xAlways correctly load the trailer.
xAlways secure loads correctly with suitable and undamaged attach-
ment rope or straps.
Driving with a trailer
Adjusting the headlights
When towing a trailer, the front of the vehicle may rise and so the dipped
beam headlights may blind other drivers. Use the headlight range control to
lower the cone of light. If you do not have headlight range control, have the
headlights adjusted by a qualified dealership. Vehicles with high-intensity
discharge lamps adapt automatically and do not require adjustment.
Details of driving with a trailer
xIf the trailer has an overrun brake, apply the brakes gently at first and
then, firmly. This will prevent the jerking that can be caused by the trailer
wheels locking.

Vehicle maintenance and cleaning271
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWashing the vehicle in low temperatures: When washing the vehicle with
a hose, do not direct water into the lock cylinders or the gaps around the
doors, tailgate, or sunroof. Locks and seals could freeze!
Caution
To prevent damage to the vehicle, please observe the following before
entering an automatic car wash:
xCompare the distance between the vehicle wheels and the distance
between the guide-rails of the car wash to prevent damage to the wheels and
tyres!
xSwitch off the rain sensor and the Auto Hold function before entering a car
wash.
xCompare the height and width of your vehicle with the available height
and width when entering and driving through the car wash.
xFold in exterior mirrors Electrically retractable exterior mirrors must NOT
be folded in or out by hand. Always use the electrical power control.
xTo avoid damaging the bonnet paintwork, rest the wipers on the wind-
screen after drying them. Do not let them fall!
xLock the tailgate to prevent it from opening unexpectedly while inside the
car wash.
Washing the vehicle with high pressure cleaning equipment
When cleaning the vehicle with a high-pressure cleaner, always follow the
operating instructions for the equipment. Pay special attention to the
required pressure of the jet and the distance between the jet and the vehicle
Ÿ.
Keep a suitable distance from soft materials, such as rubber hoses or insu-
lating material, and from the parking distance warning system sensors. The parking distance sensors are fitted in the rear bumpers and, where appli-
cable, in the front bumpers Ÿ.
Do not use a nozzle that sprays the water out in a direct stream or one that
has a rotating jet for forcing off dirt Ÿ.
WARNING
The incorrect use of high pressure cleaning equipment could result in
permanent damage, visible or invisible, to the tyres or other materials. This
could result in serious accident.
xEnsure there is a suitable distance between the nozzle and the tyres.
xNever wash tyres with a concentrated jet or so-called “dirt blasters”.
Even at large spraying distances and short cleaning times, you may
damage the tyres.
WARNING
After the vehicle has been washed, the braking effect will be reduced (and
the braking distance increased) due to moisture (and ice in winter) on the
brakes.
xDry the brakes and remove ice by braking carefully. Ensure that you are
not endangering other road-users or breaking traffic regulations in the
process.
Caution
xThe temperature of the water must not be above +60 °C (+140 °F).
xTo avoid damage to the paintwork, do not wash the vehicle in full sun.
xThe sensors on the bumpers should be kept clean and free of ice at all
times to ensure the parking distance warning system and the parking aid
system operate correctly. When cleaning with pressure hoses and steam
cleaners, the sensors should be sprayed only briefly. A distance of 10 cm
between the sensors and the steam / hose nozzle must be observed.

Vehicle maintenance and cleaning 272
xDo not use a high pressure cleaner to remove ice or snow from windows
xWashing the vehicle in low temperatures: When washing the vehicle with
a hose, do not direct water into the lock cylinders or the gaps around the
doors, tailgate, or sunroof. Locks and seals could freeze!
Cleaning windows and exterior mirrors
Cleaning windows and exterior mirrors
Spray windows and exterior windows with a standard window cleaner
containing alcohol.
Dry the windows with a clean chamois leather or a lint-free cloth. The chamois
leathers used on painted surfaces are not suitable for cleaning windows
because they are soiled with wax deposits which could smear the windows.
Use window cleaner or a silicone remover to clean rubber, oil, grease and sili-
cone deposits off Ÿ.
Removing wax deposits
Automatic car washes and certain car care products may leave wax deposits
on the windows. These deposits can only be removed with a special product
or cleaning cloths. Wax deposits on the windscreen could cause the wiper
blades to judder. SEAT recommends you wipe the wax deposits off the wind-
screen with a soft cloth each time after you have washed the vehicle.
A window cleaning detergent which helps to dissolve the wax may be added
to the windscreen washer fluid to prevent the wiper blades from scratching
the windscreen. Please ensure the you add the cleaning product in the correct
proportions. Products for removing grease do not eliminate the wax deposits
Ÿ.
Special cleaning products or window cloths are available at any Technical
Service. To remove wax deposits, SEAT recommends the following products:
xFor the hottest time of the year: the window cleaner for summer use G 052
184 A1 . Proportion 1:100 (1 part detergent, 100 parts water) in the wind-
screen washer bottle.
xAll year round: the window cleaner G 052 164 A2; Proportion 1:2 in wind-
screen washer bottle (1 part concentrate, 2 parts water) in winter, up to
-18 °C (-0.4 °F), or 1:4, during the rest of the year.
xWindow cloths G 052 522 A1 for all windows and exterior mirrors.
Removing snow
Use a small brush to remove snow from the windows and exterior mirrors.
Removing ice
If possible, use a de-icing spray to remove ice. If you use an ice scraper, push
it in one direction only without swinging it. If you pull the scraper backwards,
the dirt may scratch the window.
WARNING
Dirty or misted windows reduce visibility in all directions and increase the
risk of accident and serious injury.
xDo not drive unless you have good visibility through all windows!
xRemove ice and snow from the windows and demist inside and out.
Caution
xNever mix our cleaning products with other products not recommended
by SEAT in the windscreen washer bottle. This could lead to flocculation and
may block the windscreen washer jets.
xDo not use hot or warm water to remove ice or snow from the windows and
exterior mirrors. The glass could crack!
xThe heating element for the rear window is located on the inner side of the
window. Do not stick adhesive labels over the heating elements and never
clean the inside of the rear window with corrosive or acid products or other
similar chemical cleaning products.

Vehicle maintenance and cleaning 276
Before applying the product, use a soft cloth to remove dust and dirt from the
rubber seals.
De-icing the door lock cylinder
To de-ice the lock cylinders, SEAT recommend the use of genuine SEAT spray
with lubricating and anti-corrosive properties.
Caution
The use of products containing degreasing agents to de-ice the locks may
rust the lock cylinder.
Protection of vehicle undercarriage
The vehicle underbody is coated to protect it from chemical and mechanical
damage. The protective coat on the undercarriage may wear through use
while driving. Therefore, SEAT recommends that the protective coating on the
undercarriage and on the running gear should be regularly checked, and
repaired if necessary.
WARNING
Additional underseal or anti-corrosion products could catch fire due to the
high temperatures reached by the exhaust gas system and other engine
components.
xDo not apply additional underseal or anti-corrosion products to the
exhaust pipes, catalytic converters, heat shields or other parts of the
vehicle which reach high temperatures.
Cleaning the engine compartment
The engine compartment of any motor vehicle is a potentially hazardous area
Ÿpage 304.
The engine compartment should only be cleaned by qualified personnel. If it
is not correctly cleaned, the anti-corrosion coating and consequently elec-
trical components may be damaged. Moreover, water may filter directly into
the vehicle interior through the water chamber Ÿ.
If the engine compartment is very dirty, always take the vehicle to a qualified
workshop for professional cleaning. SEAT recommends visiting a qualified
workshop.
Water box
The water box is in the engine compartment, between the windscreen and the
engine, and beneath a perforated cover. Air is taken in through the water box
from outside to the vehicle interior via the heating and air conditioning
system.
Leaves and other loose objects should be regularly cleaned away from the
water box either by hand or with a vacuum.
WARNING
When working on the engine or in the engine compartment, there is a risk
of injury, burns, accident or fire.
xBefore starting work, please ensure you are familiar with the required
procedure and the safety precautions Ÿpage 304.
xSEAT recommends you have this work performed by a qualified dealer-
ship.
Caution
If water is manually poured into the water box (for example, using a high pres-
sure cleaning appliance), this could cause significant damage to the vehicle.

Vehicle maintenance and cleaning283
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Notes for the user
Labels and plates
Some parts in the engine compartment come from the factory with certifi-
cates of safety, labels or plates containing important information regarding
the operation of the vehicle, for example, on the petrol cap, on the
passenger's sun visor, on the driver's door strut, or on the floor of the luggage
compartment.
xNever remove these certificates of safety, labels or plates, and ensure
they are kept in good condition and are legible.
xIf a vehicle part, bearing a certificate of safety, label or plate, is replaced,
the qualified workshop should attach the information back in the same place.
Certificate of safety
A certificate of safety on the door strut states that all the safety standards and
regulations established by the national traffic authorities responsible for
road safety were met at the time of manufacture. It may also give the month
and year of manufacture, together with the chassis number.
Warning of high voltage label*
There is a label close to the bonnet lock which warns of high voltage in the
vehicle electrical installation. The vehicle ignition system complies with
several standards, including the Canadian standard, ICES-002.
Using your vehicle in other countries and continents
The vehicle is manufactured at the factory for use in a particular country in
accordance with the national legislation in force at the time of manufacture.If the vehicle is sold in another country or used in another country for an
extended period of time, the applicable legislation of that country should be
observed.
It may be necessary to fit or remove certain pieces of equipment or to deacti-
vate certain functions. Service work may also be affected. This is particularly
true if the vehicle is used in a different climate for an extended period of time.
As there are different types of frequency bands around the world, you may
find that the radio or navigation system supplied at the factory does not work
in another country.
Caution
xSEAT does not accept liability for any damage to the vehicle due to the use
of a lower quality fuel, an inadequate service or the non-availability of
genuine spare parts.
xSEAT does not accept liability if the vehicle does not comply in part or in
full with the legal requirements of other countries or continents.
Radio reception and the aerial
The aerial of radio and navigation systems fitted at the factory may be
mounted in different parts of the vehicle:
xOn the inside of the rear window, next to the rear window heating,
xon the inside of the rear side windows,
xon the inside of the windscreen,
xon the roof of the car.
Aerials mounted on the inside of a window can be recognised by the fine
wires.

Checking and refilling levels295
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Driving with insufficient fuel reserve could result in the vehicle breaking
down in traffic and a serious accident.
xIf the fuel level is too low then the fuel supply to the engine can become
irregular especially on slopes.
xIf the engine “is choked” or stalls due to lack of or irregularity of the
fuel supply, the power steering as well as all of the driver assistance
systems including braking assistance will stop working.
xAlways refuel when there is only one quarter of the fuel tank left to
avoid running out of fuel.
Caution
xAlways pay attention to any lit lamps and to the corresponding descrip-
tions and instructions to avoid damage to the vehicle.
xNever run the tank completely dry. An irregular fuel supply may lead to
ignition faults and unburnt fuel could enter the exhaust system. This could
damage the catalytic converter filter or the diesel particulate filter!
Note
The arrow next to the fuel pump symbol on the instrument panel Ÿpage 294,
fig. 169 indicates the side of the vehicle on which the tank flap is located.
Filling the tank with petrol or diesel
Before refuelling, always turn off the engine, the ignition, mobile telephones,
auxiliary heating and keep them off during refuelling.
Unscrewing the tank cap
xThe tank flap is at the rear of the vehicle on the right.
xPress the rear of the tank flap to open it.
xUnscrew the tank cap anti-clockwise and insert it in the hole in the tank
flap hinge Ÿfig. 170.
Refilling
The correct petrol type for the vehicle is located on a sticker inside the fuel
tank flap Ÿpage 297.
xIf the automatic filler nozzle is operated correctly, it will switch itself off as
soon as the tank is full Ÿ.
xDo not continue to refuel if it is turned off! Otherwise, this will fill the
expansion chamber and fuel may leak out if the ambient conditions are warm.
Fig. 170 Open tank flap
with tank cap attached to
the holder.

Checking and refilling levels 296
Closing the tank cap
xScrew on the tank cap clockwise until it you hear it click into position.
xPress the tank flap until you hear it click into place. The tank flap must be
flush with the body contour.
WARNING
Do not continue refilling once the fuel nozzle has switched itself off. The
fuel tank may be filled too much. As a result, fuel may spurt out and spill.
This could lead to a fire, explosion and severe injuries.
Caution
xAlways remove any fuel spilled on the vehicle paintwork immediately to
avoid damage to the wheel housing, the tyre and vehicle paintwork.
For the sake of the environment
Spilt fuel can contaminate the environment.
Refilling precautions
Information on bulb replacement Ÿpage 360.
Checklist
Never work on the engine or in the engine compartment if you are not familiar
with the operations to be carried out, the applicable safety standards and
especially if you do not have the instruments, liquids and tools necessary
Ÿpage 304, “Working in the engine compartment”! Have the work carried
out by a qualified workshop if you are uncertain. Check the following regu-
larly, preferably when you refuel:
xWindscreen washer fluid level Ÿpage 124
xEngine oil level Ÿpage 309
xEngine coolant level Ÿpage 313
xBrake fluid level Ÿpage 210
xTyre pressure Ÿpage 323
xVehicle lighting required to guarantee road safety:
–Indicators
– Side lights, dipped headlights and full beam headlights
– Rear lights
–Brake lights
– Rear fog light Ÿpage 116
WARNING
Not following the checklist prepared for your own safety could lead to acci-
dents and severe injuries.
xAlways follow the check list and perform the necessary operations.

Checking and refilling levels303
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xRotate the shut off on the cover clockwise Ÿpage 302, fig. 171 and open
the cover forwards.
xUnscrew the tank filler neck cap Ÿpage 302, fig. 172 anticlockwise.
Refilling AdBlue
Only use AdBlue that is approved by SEAT and that complies with the ISO
22241-1 Standard. Only use genuine bottles.
xObserve the instructions and information provided by the refill bottle
manufacturer.
xObserve the expiry date.
xUnscrew the cap on the refill bottle.
xPlace the refill bottle upside down inside the tank filler neck.
xPress the refill bottle against the filler neck and keep in this position.
xAdd at least 10 litres of AdBlue (6 bottles). A lower quantity would be
insufficient.
xWait until the contents of the refill bottle have been poured into the
AdBlue tank. Do not crush or damage the bottle!
xUnscrew the liquid bottle anticlockwise and remove it carefully Ÿ.
xYou can tell when the AdBlue tank is full because the bottle will be empty.
Closing the tank filling neck
xScrew on the tank filler neck cap Ÿpage 302, fig. 172 clockwise until
it is fully inserted.
xPlace the cover and turn the shut off anticlockwise to close it.
Operations before driving
xOnly switch the ignition on after refilling.
xKeep the ignition switch on for at least 30 seconds so that the system
detects tank refilling.
xWait 30 seconds before starting the engine!
WARNING
Only keep AdBlue in its original container, tightly shut and in a safe place.
xNever keep AdBlue in empty food cans, bottles or other containers to
avoid other people mistaking it for something else.
xKeep the AdBlue out of the reach of small children.
Caution
xOnly refill using AdBlue expressly approved by SEAT. The use of any other
type of AdBlue could cause engine damage!
xAdBlue should never be mixed with water or any other additives. Any type
of damage caused by a mixture will not be covered by the warranty.
xDo not add AdBlue to the diesel fuel tank! Otherwise you may damage the
engine.
xNever leave the refill bottle in the vehicle. It could become permeable due
to temperature changes and bottle damage and the AdBlue could damage
the vehicle interior.
For the sake of the environment
Dispose of the refill bottle in an environment-friendly manner.
Note
Suitable AdBlue refill bottles can be purchased from a qualified workshop.
A1
A2
A1

Checking and refilling levels305
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWhen the engine is warm or hot, the cooling system is pressurised! Do
not unscrew the cap on the expansion tank when the engine is hot. Other-
wise, coolant may spray out under pressure causing burns and serious
injury.
Carefully and slowly unscrew the cap anticlockwise, gently pressing
down on it.
Always protect your face, hands and arms from hot coolant and
steam using a large, thick cloth.
xWhen refilling liquids, avoid spilling them on parts of the engine and
the exhaust system. Spilled liquids could cause a fire.
WARNING
The high voltages of the electrical system can give electric shocks as well
as causing burns and serious injury and possibly even death!
xNever cause short circuits in the electrical system. The battery could
explode.
xTo minimise the risk of electric shock and serious consequences while
the engine is running or starting the engine, note the following:
Never touch the electrical wiring of the ignition system.
Never touch electric cables or the gas discharge lamps.
WARNING
In the engine compartment, there are rotating parts that could cause
serious injury.
xNever place your hands on or near the radiator fan. Touching the rotor
blades could seriously harm you. The ventilator works according to the
engine temperature and could start suddenly even when the ignition is
turned off and the key is removed.
xIf any work has to be performed when the engine is started or with the
engine running, there is an additional, potentially fatal, safety risk from the
rotating parts, such as the drive belts, alternator, radiator fan etc as well as
from the high-voltage ignition system. Always work with the utmost
caution.
Always make sure that no parts of your body, jewellery, ties, loose
clothing and long hair can be trapped by the rotating parts of the
engine. Before any work, remove ties and jewellery ( necklaces, etc), tie
longhair back and tie all items of loose clothing to your body to make
sure that they cannot be trapped by engine components.
Take extreme caution when operating the accelerator and remain
attentive. The vehicle could move, even with the electronic parking
brake activated.
xAlways make sure you have not left any objects, such as cloths or tools,
in the engine compartment. If any object is left in the engine compartment,
this could cause malfunctions, engine faults and even a fire.
WARNING
Refill liquids and certain materials can catch fire easily in the engine
compartment, causing a fire and serious injury!
xNever smoke.
xNever work close to places exposed to flames or sparks.
xNever pour service fluids over the engine. These fluid may ignite hot
engine parts and cause injuries.
xIf it is necessary to work on the fuel system or the electrical system,
please follow the instructions below:
Always disconnect the vehicle battery. When disconnecting the
battery, ensure that the vehicle is unlocked otherwise the antitheft
alarm will be triggered.
WARNING (continued)WARNING (continued)

Checking and refilling levels307
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Opening and closing the bonnet
Opening the bonnet
The lever to open the bonnet can only be used if the driver's door is open.
xBefore opening the bonnet, make sure that the windscreen wiper arms are
in place against the windscreen Ÿ.
xOpen the driver's door.
xPull the release lever Ÿpage 307, fig. 173 in the direction of the arrow.
The bonnet is released from the lock carrier by a spring mechanism Ÿ.
xLift the bonnet using the release lever Ÿpage 307, fig. 174 (arrow) and
open the bonnet fully. The bonnet is held open thanks to the gas strut.
Closing the bonnet
xTo close the bonnet, pull it down to overcome the gas strut pressure
Ÿ.
xAllow the bonnet to fall into the lock carrier. Do not press down.
If the bonnet is not correctly closed, open it once again and close it correctly.
The bonnet is correctly closed when it is flush with the corresponding parts
on the bodywork.
WARNING
If the bonnet is not correctly closed, it could suddenly open while driving
leaving the driver without visibility. This could result in serious accident.
xAfter closing the bonnet, always check that it is properly secured by the
locking mechanism in the lock carrier. The bonnet must be flush with the
surrounding body panels.
xWhile driving, if you notice that the bonnet is not correctly closed then
stop immediately and close it correctly.
xOnly open and close the bonnet when there is nobody within its range.
Fig. 173 In the footwell
on the driver side: Lever
for unlocking the bonnet.
Fig. 174 Release lever to
open the bonnet in the
radiator grille.