lock Seat Alhambra 2010 Owners Manual

Driving209
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Caution
xIf you stop on a hill with a gear ratio engaged, do not try to prevent the
vehicle from rolling back by pressing on the accelerator. This could cause
overheating and damage the automatic gearbox.
xNever allow the vehicle to move with the gear selector lever in N, espe-
cially with the engine turned off. The automatic gearbox will not be lubricated
and could be damaged.
Recommended gear indication
In some vehicles, the recommended gear for reducing fuel consumption is
displayed on the instrument panel:
Information for cleaning the diesel particulate filter
The exhaust gas system control recognises when the diesel particulate filter
is blocked, and helps to clean it by recommending a specific gear for driving.
It may therefore be necessary to drive with the engine at an exceptionally high
speed Ÿpage 255.
WARNING
The recommended gear display is intended as a guideline only; it should
never replace the driver's attention to driving carefully.
xResponsibility for selecting the correct gear for each situation
continues to lie with the driver, for example when overtaking, climbing a
hill or towing a trailer.
For the sake of the environment
Selecting the most appropriate gear for the situation will help you to save
fuel.
Note
The recommended gear display is switched off when the clutch pedal is
pressed.
DisplayMeaning
ˆOptimum gear.
žRecommendation to change up a gear.
ŸRecommendation to change down a gear.
WARNING (continued)

Driving 210
Braking, stopping and parking
Introduction
The assisted braking systems include the anti-lock braking system (ABS), the
brake assist system (BAS), the electronic differential system (EDS), the trac-
tion control system (TCS) and the electronic stabilisation program (ESP).
Additional information and warnings:
xTo wi ng m o d e Ÿpage 260
xStart assist systems Ÿpage 221
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Driving with worn brake pads or a faulty brake system may lead to serious
accident.
xIf I lights, alone or accompanied by a warning message on the instru-
ment panel, please go immediately to a specialist workshop to check the
brake pads and to replace them if they are worn.
WARNING
Careless parking can cause serious injury.
xNever remove the key from the ignition if the vehicle is in motion. The
steering lock may engage and locked the steering wheel making the
vehicle impossible to control.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as wood, leaves, spilled
fuel, dried grass, etc).
xAlways apply the electronic parking brake when you leave your vehicle
and when you park.
xNever leave children or disabled people alone in the vehicle. They could
release the electronic parking brake, activate the selector lever or gear
stick and start the vehicle moving. This could result in serious accident.
xAlways take all the keys with you whenever you leave the vehicle. The
engine could accidentally be started and electrical equipment such as the
windows could accidentally be operated resulting in serious injury.
xNever leave children or disabled people alone in the car. They could be
trapped in the car in an emergency and will not be able to get themselves
to safety. For example, depending on the time of the year, temperatures
inside a locked and closed vehicle can be extremely high or extremely low
resulting in serious injuries and illness or even death, particularly for
young children.
Caution
xSpecial care should be taken when parking in areas with high kerbs or
fixed barriers. Objects protruding from the ground may damage the bumper
or other parts of the vehicle during manoeuvres. To avoid damage, stop
before the wheels touched the barrier or kerb.
xSpecial attention is required when driving through entrances, over ramps,
kerbs or other objects. The vehicle underbody, bumpers, mudguards and
running gear, and the engine and exhaust system could be damaged as you
drive over these objects.
WARNING (continued)

Driving 212
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
WARNING
Driving with brakes in bad condition could result in a serious accident.
xIf the brake warning lamp H does not go out, or if it lights up when
driving, the brake fluid level in the reservoir is too low or there is a fault in
the brake system. Obtain professional assistance immediately
Ÿpage 219, “Brake fluid”.
xIf the brake warning lamp H lights up together with the ABS warning
lamp J, the regulation function of the ABS could be malfunctioning. As a
result, the rear wheels can lock relatively easily when braking. If the rear
wheels lock this could result in loss of vehicle control! If possible, reduce
your speed and drive carefully to a specialist workshop close by to check
the brake system. During the following journey, avoid sudden braking and
manoeuvres.
xIf the ABS warning lamp J does not go out or if it lights while driving,
the ABS is malfunctioning. The vehicle can only be stopped using normal
braking without ABS. The protection provided by the ABS is not available.
Visit a specialised workshop as soon as possible.
xIf I lights, alone or accompanied by a warning message on the instru-
ment panel screen, please go immediately to a specialist workshop to
check the brake pads and to replace them if they are worn.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Electronic parking brake
Applying the electronic parking brake
The parking brake can be applied whenever the vehicle is at a standstill, even
when the ignition is switched off. Always apply the parking brake when you
leave your vehicle and when you park.
xPull button until the control lamp G on the button lights up.
xThe parking brake is applied when the control lamp H lights up on the
instrument panel Ÿpage 211.
Releasing the electronic parking brake
xSwitch the ignition on.
Fig. 143 Detailed view of
the centre console: elec-
tronic parking brake
switch
G

Driving 214
xSwitch off the engine and release the brake pedal.
xRemove the key from the ignition.
xIf necessary, turn the steering wheel slightly to lock the steering.
xWith a manual gearbox, engage the 1st gear on flat ground and slopes, or
even the reverse gear on hills, and release the clutch pedal.
xEnsure that all passengers leave the vehicle, especially children.
xWhen leaving the vehicle, take all keys with you.
xLock the vehicle.
Additional information for steep slopes and hills
Before switching off the engine, rotate the steering wheel so that if the
vehicle should move then it will be held by the kerb.
xOn slopes, turn the front wheels so that they are against the edge of the
kerb.
xUphill, turn the wheels towards the centre of the road.
WARNING
The components of the exhaust system reach very high temperatures. This
could cause a fire and considerable damage.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as wood, leaves, spilled
fuel, dried grass, etc).
Caution
xSpecial care should be taken when parking in areas with high kerbs or
fixed barriers. Objects protruding from the ground may damage the bumper
or other parts of the vehicle during manoeuvres. To avoid damage, stop
before the wheels touched the barrier or kerb.
xSpecial attention is required when driving through entrances, over ramps,
kerbs or other objects. The vehicle underbody, bumpers, mudguards and running gear, and the engine and exhaust system could be damaged as you
drive over these objects.
Information about the brakes
For the first 200 to 300 km (100 to 200 miles), new brake pads have not yet
reached their maximum braking capacity, and need to be run in first Ÿ.
The slightly reduced braking effect can be compensated for by increasing
pressure on the brake pedal. While running in, the full braking distance or
emergency braking distance is larger then when the brake pads have been
run in. While running in, avoid full power braking or situations requiring
braking performance. For example, in heavy traffic.
The rate of wear of the brake pads depends to a great extent on the condi-
tions in which the vehicle is used and the way the vehicle is driven. If the
vehicle is used frequently in city traffic or for short trips or driven sport style,
visit a specialist workshop regularly more frequently than advised in the
Maintenance Programme to have the bake pads checked.
If you drive with wet brakes, for example, after crossing areas of water, in
heavy rainfall or even after washing the car, the effect of the brakes is less-
ened as the brake discs are wet or even frozen (in winter). At higher speed,
dry the brakes as quickly as possible by braking gently several times. Only do
this without endangering vehicles behind you or any other road users Ÿ.
A layer of salt on the discs and brake pads will reduce brake efficiency and
increase braking distance. If you drive for a prolonged period on salted roads
without braking then brake carefully several times to eliminate the layer of
salt on the brakes Ÿ.
If the vehicle remains parked for considerable lengths of time, is used little,
or if the brakes are not used, there may be corrosion on the brake discs and
a buildup of dirt on the brake pads. If the brakes are not used frequently, or
if rust has formed on the discs, SEAT recommends cleaning the pads and

Driving 216
Caution
xNever make the brakes slip by pressing the pedal gently, if it is not really
necessary to brake. Continuously pressing on the brake pedal will heat the
brakes. This could significantly reduce braking power, increase braking
distance or even result in the total failure of the brake system.
xReduce speed, move down a gear or select a shorter range of gears before
long steep slopes. This allows you to use the engine braking effect and to
reduce the strain on the brake system. Otherwise, the brakes may overheat
and fail. Only use the brakes to reduce speed or to stop.
Note
When checking the front brake pads, take the time to also check the rear
brake pads. The thickness of the brake pads should be checked visually and
regularly, by looking through the openings in the wheel rims or from under-
neath the vehicle. If necessary, remove the wheels to check them thoroughly.
SEAT recommends visiting a qualified workshop.
Assisted braking systems
The assisted braking systems ESP, ABS, BAS, TCS and EDS only operate when
the ignition is switched on. They contribute significantly to increasing active
safety.
Electronic stability programme (ESP)
ESP reduces the risk of skidding and increases the vehicle stability by braking
individual wheels under specific driving conditions. ESP detects critical
handling situations, such as understeer, oversteer and wheelspin on the
driven wheels. The system stabilises the vehicle by braking individual wheels
or by reducing the engine torque.
The ESP has limits. It is important to realise that the ESP is also subject to the
laws of physics. ESP will not be able to deal with all situations with which drivers may be faced. For example, if the road surface changes suddenly then
ESP will not be useful in all cases. If the vehicle suddenly enters a section
covered by water, mud or snow then ESP will not provide assistance in the
same way as on dry ground. If the vehicle loses its grip on the ground and
moves on a film of water (aquaplaning), the ESP will not be able to assist the
driver to control the vehicle due to the loss of adherence with the road surface
preventing braking and steering. If the vehicle is driven through series of
bends at high speed, the ESP will not always be as effective: the vehicle reac-
tion to aggressive driving is not the same as at reduced speeds. When driving
with a trailer, ESP does not provide the same amount of vehicle control as
without a trailer.
Adjust your speed and driving style to road, traffic and weather conditions.
ESP cannot push the limits of the laws of physics; improve the transmission
available or maintain the vehicle on the road if a lack of driver attention
creates an inevitable situation. Otherwise, ESP assists in maintaining vehicle
control in extreme situations and uses the movements of the steering made
by the driver to maintain the vehicle moving in the desired direction. If the
vehicle is driven at such a speed that it will leave the road before ESP can
intervene then the system cannot provide assistance.
The ABS, BAS, TCS and EDS systems are incorporated into the ESP. The ESP is
always on. The ESP should only be turned off using the TCS button
Ÿpage 218, fig. 144 when traction is insufficient. Always remember to turn
on the TCS once more when the vehicle has traction once again.
Anti-lock brake system (ABS)
ABS can prevent the wheels from locking during braking until just before the
vehicle stops thus helping the driver to steer the vehicle and maintain
control. This means that, even during full braking, the risk of skidding is
reduced:
xPress and hold the brake pedal fully. Do not remove your foot from the
brake pedal or reduce braking force!
xDo not “pump” the brake pedal, or reduce braking force!
xMaintain vehicle direction when braking fully.

Driving217
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWhen the brake pedal is released or when the brake force is reduced, ABS
is turned off.
ABS control can be observed by vibration of the brake pedal and noise. You
should never expect the ABS to reduce the braking distance under any
circumstances. Braking distances will increase when driving on gravel, recent
snow or on icy and slippery ground.
When driving on loose ground, the all-terrain configuration of the ABS is auto-
matically turned on. When ABS is activated, the front wheels may lock briefly.
This shortens the braking distance in off-road situations as the wheels are
prevented from digging into loose surfaces. All-terrain ABS only intervenes
when driving in a straight line. When the front wheels are turned, the normal
ABS is activated.
Braking assist system (BAS)
The brake assist system may reduce the required braking distance. The brake
assist system boosts the braking force if you press the brake pedal quickly in
an emergency. As a result, the braking pressure increases rapidly, the braking
force is multiplied and the braking distance is reduced. This enables the ABS
to be activated more quickly and efficiently.
¡Do not lift your foot off the brake pedal! When the brake pedal is released or
when the brake force is reduced, braking assist automatically turns off the
brake servo.
Traction control when accelerating (TCS)
In the event of wheelspin, the traction control system reduces the engine
torque to match the amount of grip available. The TCS makes some situations
easier, for example, when starting, accelerating or going uphill, even in unfa-
vourable road conditions.
The TCS can be switched on or off manually Ÿpage 218.
Electronic differential lock system (EDS)
EDS is available when driving in straight lines under normal conditions. When
the EDL detects wheelspin, it brakes the spinning wheel and directs the power to the other driven wheels. To prevent the disc brake of the braked
wheel from overheating, the EDL cuts out automatically if subjected to exces-
sive loads. The EDL will switch on again automatically when the brake has
cooled down.
WARNING
Driving at high speed on icy, slippery wet ground can result in loss of
vehicle control and serious injury to the driver and passengers.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions. Even though the braking assist systems, ABS, BAS,
EDS, TCS and ESP, provide more security, do not take unnecessary risks
while driving.
xBraking assist systems can not overcome the laws of physics. Even with
ESP and other systems, slippery and wet roads will always be dangerous.
xDriving to quickly on wet ground can result in the wheels losing contact
with the ground in an effect known as aquaplaning. Without adherence, it
is impossible to brake, steer or control the vehicle.
xBraking assist systems cannot avoid accidents if, for example, the
driver does not respect safety distances or drives to quickly in difficult
conditions.
xEven though braking assist systems are extremely effective and help
control the vehicle in difficult situations, remember that the vehicle
stability depends on tyre grip.
xWhen accelerating on a slippery surface, for example on ice and snow,
press the accelerator carefully. The wheels can still slip even with braking
assist systems resulting in loss of vehicle control.
WARNING
The effectiveness of the ESP can be considerably reduced if other compo-
nents and systems affecting driving dynamics are not maintained or are not

Driving and the environment255
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Engine management and exhaust gas
purification system
Introduction
Additional information and warnings:
xChanging gear Ÿpage 201
xRefuelling Ÿpage 293
xFuel Ÿpage 297
xEngine oil Ÿpage 309
xVehicle battery Ÿpage 318
xInformation stored in the control units Ÿpage 285
xTow-starting and towing away Ÿpage 375
WARNING
The components of the exhaust system reach very high temperatures. This
could cause a fire.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as dried grass).
xDo not apply additional underseal or anti-corrosion coatings to the
exhaust pipes, catalytic converter, heat shields or the diesel particulate
filter.
Warning lamps
lights upPossible causeSolution
%0#Fault in engine management
(Electronic Power Control).Take the vehicle to a qualified
workshop as soon as possible
and have the engine checked.
DPre-heating a diesel engine
before starting the engine.Ÿpage 195
BFault in catalytic converter.
You should reduce speed accord-
ingly. Drive carefully until you
reach the next qualified work-
shop. Have the engine checked
there.
¬Diesel particulate filter
blocked
Drive for 15 minutes in 4th gear
(manual gearbox), or in D (auto-
matic gearbox) at a minimum
speed of 70 km/h (45 mph).
Observe speed limits Ÿ.
If the warning lamp remains lit
up, take the vehicle to a quali-
fied workshop Ÿpage 256.
flashesPossible causeSolution
DFault in the engine manage-
ment (diesel engines).Take the vehicle to a qualified
workshop as soon as possible
and have the engine checked.
B
Combustion fault which could
damage the catalytic con-
verter.You should reduce speed accord-
ingly. Drive carefully until you
reach the next qualified work-
shop. Have the engine checked
there.

Driving and the environment 256
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
Observe traffic regulations when cleaning the diesel particulate filter while
driving.
xOnly carry on driving if visibility, weather, road and traffic conditions so
permit.
xNever endanger your safety or that of other road users.
Caution
Always pay attention to any lit lamps and to the corresponding descriptions
and instructions to avoid damage to the vehicle.
Note
While the indicators ¬, B or %0# remain lit, there may be engine problems,
fuel consumption may be greater and the engine may lose power
Catalytic converter
The catalytic converter permits the subsequent treatment of the exhaust
gases thus reducing contaminating gas emissions. To ensure a longer
working life for the exhaust system and catalytic converter in a petrol engine:
xAlways use unleaded petrol.
xNever run the tank completely dry.
xDo not top up with too much engine oil Ÿpage 309.
xDo not tow-start the vehicle; use the starter cables Ÿpage 371.If you should notice misfiring, uneven running or loss of power when the car
is moving, reduce speed immediately. Have the car inspected by a qualified
workshop. If this happens, unburnt fuel can enter the exhaust system and
escape into the atmosphere. The catalytic converter can also be damaged by
overheating.
For the sake of the environment
Even when the emission control system is working perfectly, there may be a
smell of sulphur from the exhaust gas under some conditions. This depends
on the sulphur content of the fuel being used.
Diesel particulate filter
The diesel particulate filter removes soot particulates from the exhaust gas.
The filter retains these particulates and burns them. To assist the combustion
process, SEAT recommends you avoid frequent short trips.
xAlways use diesel with a low sulphur content Ÿpage 297.
xNever use petrol or fuel oil.
xNever use biodiesel. However, a blend prepared by the diesel manufac-
turer containing biodiesel within the limits established by the EN 590
standard may be used Ÿpage 297.
xNever run the tank completely dry.
xDo not top up with too much engine oil Ÿpage 309.
xDo not tow-start the vehicle; use the starter cables Ÿpage 371.
In order to reduce blocking of the diesel particulate filter, some vehicles with
an automatic gearbox may increase the engine speed slightly to automati-
cally start cleaning the diesel particulate filter. The warning lamp will not light
up in this case
¬.

Trailer towing261
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xIf the trailer absorbs excessive electric current, the vehicle electronics
may be damaged.
xNever connect the trailer's electric system to the electrical connections of
the rear lights or any other power sources. Only use suitable connections for
providing electric current to the trailer.
Note
Towing a trailer places additional demands on the vehicle. At SEAT, we recom-
mend additional services between the normal inspection intervals if the
vehicle is used frequently for towing a trailer.
Note
In some countries, an additional fire extinguisher is required if the trailer
weight is more than 2500 kg
Electric tow hitch ball
The rotation radius of the tow hitch ball should be free of people, animals and
objects Ÿ.
The tow hitch is located in the bumper. The electric tow ball is fixed and
cannot be removed.
Releasing and unfolding the tow ball
xStop the vehicle and apply the electric parking brake.
xSwitch the engine off.
xOpen the tailgate.
xPress the knob briefly Ÿfig. 163. The tow ball is released electronically
and folds out automatically; the button indicator will blink.
xMove the ball joint until it inserts and the button indicator lights.
xClose the tailgate.
xBefore hitching the trailer, remove the dust guard from the ball.
xThe indicator only lights when the tailgate is open and when a trailer is
not hitched.
Restoring the tow ball to its originally position
xStop the vehicle and apply the electric parking brake.
xSwitch the engine off.
xRemove the trailer and disconnect the cable between the vehicle and
trailer. If necessary, remove the socket adapter.
xPlace the dust guard over the ball.
xOpen the tailgate.
xPress the knob briefly Ÿfig. 163. The tow ball is electronically released;
the indicator blinks.
xPush the tow ball into the bumper until it locks in position and the button
indicator lights.
xClose the tailgate.
Fig. 163 Right-hand side
of the luggage compart-
ment: button to electri-
cally release the tow hitch
ball.

Trailer towing263
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Trailer electric socket
The electric connection between vehicle and trailer is a 13-pin socket. If the
trailer plug has seven pins, an adapter cable must be used.
Trailer rear lights
Check the trailer rear lights to ensure they work correctly and remain legal.
Ensure that the trailer does not use more than the maximum power
Ÿpage 260.
Trailer connected to the antitheft alarm:
xWhen a vehicle comes from the factory fitted with an antitheft alarm and
tow hitch.
xWhen the trailer is connected to the vehicle using the socket.
xWhen the vehicle and trailer electrical systems work correctly and are not
damaged.
xWhen the vehicle is locked using the vehicle key and the antitheft alarm
is turned on.
When the vehicle is locked, the alarm is triggered when the electrical connec-
tion between the vehicle and the trailer is removed.
Always turn off the anti-theft alarm system before connecting or discon-
necting a trailer. Otherwise, the tilt sensor may erroneously activate the
alarm.
WARNING
Erroneous or unsuitable connection of electric cables may supply energy to
the trailer causing an anomaly in the vehicle electronics that could result
in an accident with serious consequences.
xAll work on the electrical system must be carried out only by a
specialist workshop.
xNever connect the trailer's electric system to the electrical connections
of the rear lights or any other power sources.
Caution
Do not leave the trailer connected to the vehicle when parked; places on its
support wheel or its supports. For example, when changing the load or a
puncture, the vehicle will be pushed up or down. The force acting on the tow
hitch and the trailer could damage the vehicle or the trailer.
Note
In case of a fault in the vehicle or trailer electrical system or in case of prob-
lems with the antitheft alarm system, have the system checked by a specialist
workshop.
Note
If the trailer accessories use energy from the socket when the engine is
stopped, the battery will be discharged.
Note
For technical reasons, trailers fitted with rear LED lights cannot be connected
to the antitheft alarm system.
Note
If the vehicle battery is running low, the electrical connection with the trailer
is automatically cut.
Note
With the engine running, the electrical equipment on the trailer will consume
power.