brake Seat Alhambra 2010 User Guide

Lights and visibility 132
Exterior mirrors
Synchronised mirror adjustment
xIn the menu Settings - Convenience select whether or not the mirrors
should move in synchronisation Ÿpage 70.
xTurn the knob to position L.
xAdjust the left-hand exterior mirror. The right exterior mirror will be
adjusted at the same time (synchronised).
xIf necessary the right exterior mirror adjustment may need correcting. Turn
the knob to position R.
Automatic anti-dazzle exterior mirror, driver's side
The automatic anti-dazzle exterior mirror is controlled in the same way as the
automatic anti-dazzle rear vision mirror Ÿpage 131.
Store the reverse settings for the passenger exterior mirror
xSelect the vehicle key in which the setting is to be stored.
xUse this key to unlock the vehicle.
xConnect the automatic parking brake.
xSwitch the ignition on.
xMove the gear lever to neutral.
xIn the menu Settings - Convenience activate the function Mirror
adjustment.
xSelect reverse gear.
xAdjust the front passenger exterior mirror so that you can see, for
example, the kerb area.
xThe new position of the mirror will be stored automatically and allocated
to the vehicle key that was used to unlock the vehicle. For vehicles with seat
memory, please see Ÿpage 137.
Activating the passenger exterior mirror settings
xTurn the exterior mirror knob to position R.
xWith the ignition switched on, select reverse gear.
xThe stored position of the passenger exterior mirror for reverse gear is
deleted when driving forwards at 15 km/h, or if the knob is turned from posi-
tion R to another position.
Turn the knob to the required position:
#Electric folding exterior mirrors Ÿ.
?Switch on the exterior mirror heating This only heats up if the
ambient temperature is less than +20 °C (+68 °F).
,Adjust the left-hand exterior mirror by turning the knob for-
wards, backwards, to the left or to the right.
2Adjust the right-hand exterior mirror by turning the knob for-
wards, backwards, to the left or to the right.
Zero position. Exterior mirror unfolded, exterior mirror heating
off, adjustment of exterior mirror not possible.
Fig. 80 In the driver door:
exterior mirror controls

Seats and storage compartments 138
burns to the back, buttocks and legs from use of the seat heating that may
lead to a long healing process or that may never completely heal. Seek
medical advice if you have doubts regarding your health.
xPeople with a limit pain and temperature threshold must never use seat
heating.
Caution
xTo avoid damaging the heating elements of the seat heating, please do
not kneel on the seat or apply sharp pressure at a single point to the seat
cushion and backrest.
xLiquids, sharp objects and insulating materials on the seat could damage
the seat heating.
xIn the event of smells, switch off the seat heating immediately and have
the unit inspected by a qualified workshop.
For the sake of the environment
The seat heating should remain on only when needed. Otherwise, it is an
unnecessary fuel waste.
Seat with position memory
Memory buttons
Individual settings for the driver seat and the exterior mirror can be assigned
to each memory button.
Storing exterior mirror settings for driving forwards
xConnect the automatic parking brake.
xMove the gear lever to neutral.
xSwitch the ignition on.
xAdjust the front seat and the exterior mirrors.
xKeep the button held down for more than one second Ÿfig. 86.
xPress the required memory button for the following 10 seconds. A sound
confirms the settings have been stored.
Storing front passenger exterior mirror settings for driving in reverse gear
xConnect the automatic parking brake.
xMove the gear lever to neutral.
WARNING (continued)
Fig. 86 Memory buttons
on the outside of the
driver seat
SET

Driving197
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
For automatic gearbox vehicles the key can only be removed from the ignition
lock if the gear selector lever is in position P. In this case, press and release
the selector lever locking button.
Starter button*
The starter button can only be used if there is a valid key inside the vehicle.
On leaving the vehicle with the ignition switched off, the electronic lock on
the steering column is activated when the driver's door is opened
Ÿpage 192.
Switching the ignition on/off
xBriefly press the starter button once without pressing the clutch or brake
pedal Ÿ.Emergency starting function
If the system has not recognised a valid key inside the vehicle, the emergency
starter function is activated. The corresponding information text is displayed
on instrument panel. This may occur, for example, if the key battery is flat or
very low:
xPlace the key close to the steering column immediately after passing the
start button.
xThe engine starts automatically.
Emergency disconnection
If it is not possible to switch off the engine by briefly pressing the starter
button, the emergency disconnection system should be used:
xPress the starter button twice within a second or press it once for more
than two seconds Ÿ in “Stopping the engine” on page 199.
xThe engine turns off automatically.
Re-starting the engine
If, after the engine is switched off, a valid key is not detected in the vehicle,
the engine can only be started after an interval of approximately 5 seconds.
The corresponding message is displayed on the instrument panel.
After this interval, it will not be possible to start the engine without a valid key
inside the vehicle.
WARNING
Unintentional movements of the vehicle could cause serious injury.
xWhen the starter button is pressed do not press the brake or clutch
pedal as the engine will start immediately.
Fig. 135 Detailed view of
the centre console: KESSY
starter and lock system:
Starter button.

Driving 198
WARNING
Careless or incorrect use of vehicle keys may result in severe injury and
accident.
xAlways take all the keys with you whenever you leave the vehicle. Chil-
dren and other unauthorised persons could lock the vehicle, start the engine or switch on the ignition and any electrical components such as the
electric windows.
Note
In vehicles with a diesel engine and KESSY, the starting of the engine may be
delayed due to pre-heating of the engine.
Starting the engine
Complete operations only in the sequence given:
WARNING (continued)
StepVehicles without KESSYVehicles wi th KESSY
1.Press the brake pedal and keep pressed until step 5 has been completed.
1 a.In vehicles with a manual gearbox: Press the clutch pedal all the way and keep pressed until the engine starts.
2.Put the gearstick in neutral or the selector lever in position P or N.
3.
Only in vehicles with diesel engine: To preheat, turn the key in the igni-
tion lock to position Ÿpage 196, fig. 134 . A warning lamp lights
up in the control panel
D.
4.Turn the key in the ignition lock to position Ÿpage 196, fig. 134 ;
do not press the accelerator.Press the starter button Ÿpage 197, fig. 135; do not press the acceler-
ator. To start the engine, the system should detect a valid key inside
the vehicle.
5.When the engine has started, release the key in the ignition lock.When the engine starts, release the starter button.
6.If the engine does not start, stop the process and try again after one
minute.If the engine does not start, stop the process and try again after one
minute. If necessary, perform an emergency start Ÿpage 197.
7.Disconnect the electronic parking brake when you wish to start driving Ÿpage 210.
A1
A2

Driving199
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Never leave the vehicle unattended if the engine is running. The vehicle
could move off suddenly, especially if it is in gear, resulting in an accident
and serious injury.
WARNING
Cold start sprays could explode or cause a sudden increase in the engine
speed.
xNever use start boosters.
Caution
xAn attempt to start the engine while driving or starting the engine imme-
diately after turning it off can cause damage to the engine or starter motor.
xWhen the engine is cold, avoid high revs and heavy acceleration and do
not make the engine work hard.
xDo not push or tow start the engine. Sunburnt fuel could damage the cata-
lytic converter.
For the sake of the environment
Do not warm the engine at idle speed; start driving immediately if the visi-
bility is OK. This helps the engine reach operating temperature faster and
reduces emissions.
Note
For example, if the key battery is very worn or flat, the engine cannot be
started with the starter button. In this case, remove the ignition button from
the lock and insert the key.
Note
Electrical components with a high power consumption are switched off
temporarily when the engine starts.
Note
When the engine is started cold, there may be strong vibrations for a few
moments for technical reasons. This is quite normal, and no cause for
concern.
Note
At temperatures below +5 °C (+41 °F), smoke may be given off below the
vehicle when the additional heater is connected.
Stopping the engine
Complete operations only in the sequence given:
StepVehicles without KESSYVehicles with KESSY
1.Stopping the vehicle completely Ÿ.
2.Press the brake pedal and keep pressed until step 4 has been com-
pleted.
3.In automatic gearboxes, put the selector lever in position P.
4.Connect the electronic parking brake Ÿpage 210.

Driving 200
WARNING
Never switch off the engine while the vehicle is moving. You may lose
control of the vehicle and there is a risk of serious accident.
xThe airbags and belt tensioners do not work when the ignition is
switched off.
xThe brake servo does not work when the engine is not running. To stop,
the brake pedal must be pressed with more force.
xAs the power steering does not work if the engine is not running, you
will need more strength to steer than normally.
xIf the key is removed from the ignition, the steering may lock and it will
not be possible to steer the vehicle.
Caution
If the engine has been driven at high speed for a prolonged period of time, it
may overheat when turned off. To avoid engine damage, allow the engine to
run for approximately two minutes in neutral before switching it off.
Note
In vehicles with automatic gearbox, the key can only be removed when the
selector lever is in position P.
Note
After stopping the engine, the engine compartment fan may continue running
for a few minutes, even when the ignition has been switched off or the key
removed. The radiator fan is automatically switched off.
Electronic immobiliser
The gear lock prevents the engine from being started with an unauthorised
key and the vehicle being moved.
The vehicle key has a built-in chip. It automatically deactivates the immobi-
lizer when the key is inserted into the ignition lock.
The electronic immobiliser will be activated again automatically as soon as
you remove the key from the ignition lock. In vehicles with the KESSY system,
the key should remain outside the vehicle Ÿpage 86.
For this reason, the vehicle can only be used with a genuine SEAT key with the
correct code. Coded keys can be obtained from your Authorised Service
Centre Ÿpage 78.
If an unauthorised key is used, the message SAFE or Immobiliser active is
displayed on the instrument panel. The vehicle cannot be started in this case
Note
The correct operation of the vehicle is only guaranteed when original SEAT
keys are used.
5.
Turn the key in the ignition lock
to position Ÿpage 196, fig. 134
.Briefly press the starter button
Ÿpage 197, fig. 135. If it is not
possible to switch off the engine,
use the emergency disconnec-
tion Ÿpage 197.
6.With a manual gearbox, put the vehicle in first or reverse gear.
7.
Remove the starter button from
the lock to disconnect all electri-
cal components and activate the
electronic lock on the steering
column.
StepVehicles without KESSYVehicles with KESSY
A0

Driving201
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Changing gear
Introduction
When reverse gear is engaged and the ignition is switched on the following
takes place:
xReverse lights light up.
xWhen reversing, the air conditioner automatically changes to air recircu-
lation mode.
xThe rear window heater switches on when the windscreen wiper is acti-
vated.
xAlso, the parking sensor system, the optical parking sensor and the
camera for the reverse assist system are connected.
Additional information and warnings:
xInstruments Ÿpage 64
xBraking, stopping and parking Ÿpage 210
xParking sensor system Ÿpage 225
xPark Assist system Ÿpage 229
xReverse assist system (Rear Assist) Ÿpage 234
xAir conditioning Ÿpage 179
xElectronic power control and exhaust gases purification system
Ÿpage 255
xEmergency locking and unlocking Ÿpage 348
WARNING
Rapid acceleration can cause loss of traction and skidding, especially on
slippery ground. This could cause loss of control of the vehicle resulting in
an accident and considerable damage.
xOnly use the kickdown or rapid acceleration if visibility, weather, road
and traffic conditions so permit.
WARNING
Do not allow the brakes to “rub” for a prolonged period of time, or brake
frequently or for long periods of time. Continuous braking heats up the
brakes. This could significantly reduce braking power, increase braking
distance or even result in the total failure of the brake system.
Caution
xNever make the brakes slip by pressing the pedal gently, if it is not really
necessary to brake. This will increase wear.
xReduce speed, move down a gear or select a shorter range of gears before
long steep slopes. This allows you to use the engine braking effect and to
reduce the strain on the brake system. Otherwise, the brakes may overheat
and fail. Only use the brakes to reduce speed or to stop.
WARNING (continued)

Driving 202
Warning and control lamps
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
xIf the vehicle stops and must be stopped for repairs, always park a safe
distance from surrounding traffic, turn on the hazard warning lights, stop
the engine and take all of the safety measures necessary to warn other road
users.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.lights upPossible causeSolution
K (red)Brake pedal not pressed!Press brake pedal to the floor.
K
(green)Brake pedal not pressed.
To select a range of gears, press
the brake pedal.
Please also see "Electronic park-
ing brake" Ÿpage 210.
flashesPossible causeSolution
K
(green)The selector lever locking but-
ton has not engaged. The
vehicle does not start to
move.Engage the selector lever lock
Ÿpage 206.

Driving203
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Pedals
Do not allow floor mats or other objects to obstruct the free passage of the
pedals.Floor mats should leave the pedal area free and unobstructed and be
correctly secured in the footwell zone.
In the event of failure of a brake circuit, the brake pedal must be pressed
harder than normal to brake the vehicle.
WARNING
Objects falling into the driver's footwell could prevent use of the pedals.
This could lead the driver to lose control of the vehicle, increasing the risk
of a serious accident.
xMake sure the pedals can be used at all times, with no objects rolling
underneath them.
xAlways secure the mat in the foot well.
xNever place other mats or rugs on top of the original mat supplied by
the factory.
xEnsure that no objects can fall into the driver's footwell while the
vehicle is in motion.
Caution
The pedals must always have free and unobstructed passage to the floor. For
example, in case of a fault in the brake circuit, the brake pedal will need to be
pressed further to stop the vehicle. To press the brake pedal down further will
require more force than usual.
Fig. 136 Pedals in vehi-
cles with a manual
gearbox: accelerator;
brake; clutch.
A1A2A3
Fig. 137 Pedals in vehi-
cles with an automatic
gearbox: accelerator;
brake.
A1A2

Driving 204
Manual gearbox: Engaging gears
The position of each of the gears is shown on the gear stick Ÿfig. 138.
xKeep the clutch pedal pushed all the way down.
xMove the gear stick to the required position.
In some countries, it is necessary to press the clutch pedal to the floor to start
the engine.
Selecting reverse gear
xWith the vehicle at a standstill, press the clutch pedal to the floor and
keep pressed.
xPush the gear lever down.
xMove the gear stick to the left and then forwards to reverse gear
Ÿfig. 138 .
WARNING
When the engine is running, the vehicle will start to move as soon as a gear
is engaged and the clutch released. This is also the case with the electronic
parking brake on.
xNever engage the reverse gear when a vehicle is moving forward.
Caution
To prevent damage and avoid premature wear, please observe the following:
xWhile driving, do not leave your hand resting on the gear stick. The pres-
sure applied by your hand is transmitted to the gearbox selector forks.
xAlways ensure that the vehicle is completely stopped before engaging the
reverse gear.
xWhen changing gear, always make sure the clutch pedal is pushed right
to the floor.
xNever hold the vehicle on the clutch on hills.
Fig. 138 Gear shift
pattern of a 6-speed
manual gearbox.
AR