service Seat Alhambra 2010 User Guide

Cockpit75
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Configuration Menu
Configuration
MenuFunction
Multifunction
display dataConfiguration of the multifunction display data which you
wish to see on the instrument panel display Ÿpage 73.
CompassChanging the magnetic region and calibration of the com-
pass. To calibrate the compass, please follow the instruc-
tions given on the instrument panel display.
ConvenienceChanging vehicle convenience functions Ÿpage 76.
Lights &
visibilityConfiguration of vehicle lighting Ÿpage 77.
TimeChanging the hours and minutes of the clock and the nav-
igation system. The time can be set here and the choice
can be made between the 24 hour and 12 hour display.
The S in the upper part of the display indicates that the
clock is set to summer time.
Winter tyresChanging the visual and audible speed warnings. This
function should only be used when the vehicle is fitted
with winter tyres, which are not designed for travel at
high speeds.
Settings:
LanguageChanging the language of the display texts and the navi-
gation system.
UnitsChanging the units of measurement for the temperature,
consumption and distance.
Second speedSwitching second speed display on and off
AutoholdSelecting whether the Auto-Hold function should remain
on permanently.
Travel modeChanging the headlamps for countries in which vehicles
are driven on the other side of the road. When the “mark”
is activated, the headlamps of a left-hand drive vehicle
are adjusted for driving on the left. The travel mode can
only be used for short periods of time.
ServiceCheck the service notifications or reset the service inter-
vals to zero
Manufacturer's
settings Some functions of the Configuration menu will be reset
to the factory value.
BackThe main menu is displayed again.
Configuration
MenuFunction

Unlocking and locking79
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Vehicle key
Vehicle keys
With the vehicle key Ÿfig. 40 or Ÿfig. 41 the vehicle may be locked or
unlocked remotely.The vehicle key includes an emitter and batteries. The receiver is in the inte-
rior of the vehicle. The range of the vehicle key with remote control and new
batteries is several metres around the vehicle.
If it is not possible to open or close the vehicle using the remote control key,
this should be re-synchronised Ÿpage 82 or the battery changed
Ÿpage 81.
Different keys belonging to the vehicle may be used.
Folding the key shaft in and out
When the button is pressed, the key shaft is released and unfolds.
To fold it press the button and fold the key shaft in until it locks in place.
Duplicate keys
To obtain a spare key and other vehicle keys, the vehicle chassis number is
required.
Each new key must contain a microchip and be coded with the data from the
electronic vehicle immobiliser. In vehicle key will not work if it does not
contain microchip or the microchip has not been encoded. This is also true for
keys cut for the vehicle.
The vehicle keys or new spare keys can be obtained from an authorised tech-
nical service, a specialist workshop or approved key service qualified to
create this kind of key.
New keys or spare keys must be synchronised before use Ÿpage 82.
Caution
All of the vehicle keys contain electronic components. Protect the vehicle
keys from damage, impacts and humidity.
Fig. 40 Vehicle keys.
Fig. 41 Vehicle key for
vehicles with electric
sliding doors.

Unlocking and locking109
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Garage door remote control*
Introduction
Fixed code or variable code
The garage door remote control uses either a fixed code or a variable code.
For remote controls using a variable code, the system must be synchronised
after programming Ÿpage 110.
Compatibility
SEAT recommends that before buying a remote control or electric system, you
get information from a approved technical service about which products are
compatible with the vehicle remote control.
In some countries, the use of safety controls and electric systems for garage
doors are obligatory.
WARNING
Careless use of the garage remote control can cause serious injury.
xThe garage remote control and electric systems operate with enough
energy to cause injury.
xOnly use the remote control when you can see the garage door and that
there is nobody in its way.
xWhen programming, the garage door or electric system could move
causing damage or injury.
xThe garage remote control and electric systems that do not detect
obstacles do not comply with the legal requirements in certain countries.
Using remote controls and electric systems that do not detect obstacles
increases the risk of injury or death.
xAlways read the assembly instructions and warnings from the manufac-
turer when using a garage door remote control and electric system.

Lights and visibility 124
Windscreen wiper and washer
Introduction
Additional information and warnings:
xRecirculation of air conditioning air Ÿpage 179
xWorking in the engine compartment Ÿpage 304
xCaring for and cleaning the vehicle exterior Ÿpage 269
WARNING
Water from the windscreen washer water bottle may freeze on the wind-
screen if it does not contain enough anti-freeze, reducing forward visibility.
xIn winter, ensure the windscreen washer contains enough anti-freeze.
xIn cold conditions, you should not use the wash / wipe system unless
you have warmed the windscreen with the ventilation system. The anti-
freeze could freeze on the windscreen and reduce visibility.
WARNING
Worn or dirty wiper blades reduce visibility and increase the risk of acci-
dent and serious injury.
xAlways replace damaged or worn blades or blades which do not clean
the windscreen correctly.
Caution
In icy conditions, always check that the wiper blades are not frozen to the
glass before using the wipers for the first time. In cold weather, it may help to
leave the vehicle parked with the wipers in service position Ÿpage 127.
Warning lamp
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
lights upPossible causeSolution
YWindscreen wiper fluid level
too lowTop up the windscreen wiper
bottle as soon as possible
Ÿpage 129.

Lights and visibility127
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Windscreen wipers service position
The wiper arms can be raised when the wipers are in service position
Ÿfig. 74. To place the windscreen wipers in the service position, proceed as
follows:
xThe bonnet must be closed Ÿpage 304.
xSwitching the ignition on and off.
xPress the windscreen wiper lever downwards briefly Ÿpage 125, fig. 72
.
Before driving, always lower the wiper arms. Using the windscreen wiper
lever, the windscreen wiper arms return to their initial position.
Lifting and returning windscreen wiper arms
xPlace the wiper arms in the service position Ÿ.
xOnly hold the wiper arms at the point where the blade is fixed.
Caution
xTo prevent damage to the bonnet and the wiper arms, only leave them in
the service position.
xBefore driving, always lower the wiper arms.
Fig. 74 Wipers in service
position.
A4

Lights and visibility129
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
Clean the sensitive surface of the rain sensor regularly and check the blades
for damage Ÿpage 128, fig. 76 (arrow).
Note
To remove wax and coatings, we recommend a window cleaner containing
alcohol.
Checking and topping up the windscreen washer bottle with
water
Check the water level in the windscreen washer bottle regularly and top up as
required.
xOpen the bonnet ’ Ÿpage 304.
xThe washer bottle is marked with the symbol Y on the lid Ÿfig. 77.
xCheck there is enough water in the bottle.
xTo top up, mix water with a window cleaner recommended by SEAT Ÿ.
Please follow the instructions for use found on the packaging.
xIn cold weather, a special antifreeze should also be added to prevent the
water from freezing Ÿ.
Bottle capacity
The bottle holds approximately 3.0 litres; in vehicles with headlight washer,
it is approximately 7.0 litres.
WARNING
Never mix an unsuitable antifreeze or other similar products with the wind-
screen washer water. A greasy layer may be formed on the windscreen
which will impair visibility.
xUse clean water with a window cleaner recommended by SEAT.
xIf necessary, add a suitable antifreeze to the water bottle.
Caution
xDo not mix cleaning products recommended by SEAT with other products.
This could lead to flocculation and may block the windscreen washer jets.
xWhen topping up service fluids, make absolutely certain that you fill the
fluids into the correct reservoirs. Failure to observe this point will result in
serious malfunctions and engine damage!
Fig. 77 In the engine
compartment: windscreen
washer bottle top.

Seats and storage compartments 160
Securing the base supports and roof carrier system
The mounts are the basis of a complete roof carrier system. Special fixtures
must then be added in order to safely transport luggage, bicycles, skis, surf
boards or boats on the roof. All these system components are available from
an Authorised Service Centre.
It will only be possible to install a basic support or roof carrier system if the
vehicle has a roof rail.
Securing the base supports and roof carrier system
Always secure the base supports and roof carrier system correctly.
The roof carrier system must always be installed exactly according to the
instructions provided.
The position holes are located on the inner side of the rail Ÿfig. 107.
WARNING
If the base supports and the roof carrier system are incorrectly fitted or
used in an unsuitable manner, the entire system could break free causing
accident and injury.
xAlways take the manufacturer assembly instructions into account.
xOnly use base supports and roof carrier systems that are not damaged
and are correctly fitted.
xThe base support should only be fitted to the points indicated in the
diagram Ÿfig. 107.
xSecure the base supports and roof carrier system correctly.
xCheck the screw fittings and attachments before driving and after a
short distance. During each long journey, check the attachments during
every break.
xAlways fit the roof carrier system correctly for wheels, skis and surf-
boards.
xNever change or repair the basic supports or roof carrier system.
Note
Read and take into account the instructions included with the roof carrier
system fitted and keep them in the vehicle.
Loading the roof carrier system
Loads can only be correctly secured when the roof carrier system is correctly
fitted Ÿ.
Maximum authorised roof load
The maximum authorised roof load is 100 kg (about 220 lbs). The roof load
includes the roof carrier system and the load being transported Ÿ.
Fig. 107 Attachment
points for the basic
support and the roof
carrier system.

Heating, Ventilation and Air conditioning 184
Switching the Climatronic temperature measuring unit
Press and hold the and buttons to switch the temperature display
between Celsius and Fahrenheit.
Heat
The maximum heat output required to defrost windows quickly is only avail-
able when the engine has reached its normal running temperature.
The air conditioning system does not switch on
If the air conditioning system cannot be switched on, this may be caused by
the following:
xThe engine is not running.
xThe fan is switched off.
xThe climate control fuse has blown.
xThe outside temperature is lower than approximately +3 °C (+38 °F).
xThe climate control system compressor has been temporarily switched off
because the engine coolant temperature is too high.
xAnother fault in the vehicle. Have the climate control system checked by
a qualified workshop.
Things to note
If the humidity and temperature outside the vehicle are high, condensation
can drip off the evaporator in the cooling system and form a pool underneath
the vehicle. This is normal and does not indicate a leak!
Dust and pollen filter
The dust and pollen filter with its activated charcoal cartridge serves as a
barrier against impurities in the ambient air.
For the climate control system to work with maximum efficiency, the dust and
pollen filter must be replaced at the intervals specified in the Maintenance
Programme.If the filter loses efficiency prematurely due to use in areas with very high
levels of air pollution, the filter must be changed more frequently than stated
in the Service Schedule.
Note
The climate control system must left running for a few minutes to reach the
set temperature in the vehicle interior.
Note
After starting it, any residual humidity in the climate control system could
mist over the windscreen.
Note
The air from the vents flows through the passenger compartment and out
through the outlets below the rear window. Do not cover these outlets with
items of clothing or other objects.
ACAUTO

Driving 200
WARNING
Never switch off the engine while the vehicle is moving. You may lose
control of the vehicle and there is a risk of serious accident.
xThe airbags and belt tensioners do not work when the ignition is
switched off.
xThe brake servo does not work when the engine is not running. To stop,
the brake pedal must be pressed with more force.
xAs the power steering does not work if the engine is not running, you
will need more strength to steer than normally.
xIf the key is removed from the ignition, the steering may lock and it will
not be possible to steer the vehicle.
Caution
If the engine has been driven at high speed for a prolonged period of time, it
may overheat when turned off. To avoid engine damage, allow the engine to
run for approximately two minutes in neutral before switching it off.
Note
In vehicles with automatic gearbox, the key can only be removed when the
selector lever is in position P.
Note
After stopping the engine, the engine compartment fan may continue running
for a few minutes, even when the ignition has been switched off or the key
removed. The radiator fan is automatically switched off.
Electronic immobiliser
The gear lock prevents the engine from being started with an unauthorised
key and the vehicle being moved.
The vehicle key has a built-in chip. It automatically deactivates the immobi-
lizer when the key is inserted into the ignition lock.
The electronic immobiliser will be activated again automatically as soon as
you remove the key from the ignition lock. In vehicles with the KESSY system,
the key should remain outside the vehicle Ÿpage 86.
For this reason, the vehicle can only be used with a genuine SEAT key with the
correct code. Coded keys can be obtained from your Authorised Service
Centre Ÿpage 78.
If an unauthorised key is used, the message SAFE or Immobiliser active is
displayed on the instrument panel. The vehicle cannot be started in this case
Note
The correct operation of the vehicle is only guaranteed when original SEAT
keys are used.
5.
Turn the key in the ignition lock
to position Ÿpage 196, fig. 134
.Briefly press the starter button
Ÿpage 197, fig. 135. If it is not
possible to switch off the engine,
use the emergency disconnec-
tion Ÿpage 197.
6.With a manual gearbox, put the vehicle in first or reverse gear.
7.
Remove the starter button from
the lock to disconnect all electri-
cal components and activate the
electronic lock on the steering
column.
StepVehicles without KESSYVehicles with KESSY
A0

Driving219
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Brake fluid
In the course of time, the brake fluid absorbs water from the ambient air. If
there is too much water contained in the brake fluid, the brake system could
be damaged. In addition, the boiling point of the brake fluid is significantly
lowered. When the brake fluid contains too much water and the brakes are
subject to considerable forces, bubbles of water vapour can form in the
system. These bubbles of water vapour can significantly reduce braking
power, notably increasing braking distance, and could even result in the total
failure of the brake system. Ensuring that the brake system is always func-
tioning correctly is essential for your own safety and the safety of other road
users Ÿ.
Brake fluid specifications
SEAT have developed a special brake fluid optimised for the brake systems of
their vehicles. To ensure the optimum working of the brake system, SEAT
recommends the use of brake fluid in accordance with the VW 501 14
standard. If this brake fluid is not available or another brake fluid is used for
different reasons, use a brake fluid that complies with the United States standard FMVSS 116 DOT 4 or the German standard DIN ISO 4925 CLASS 4
Ÿ.
Brake fluids conforming to the standard VW 501 14, fulfil the American
requirements of the FMVSS 116 DOT 4 standard and the German DIN ISO
4925 CLASS 4 standard. However, fluids that comply with the American
FMVSS 116 DOT 4 standard or the German DIN ISO 4925 CLASS 4 standard do
not necessarily comply with the VW 501 14 standard. Always check the infor-
mation on the brake fluid container and ensure that you are using suitable
brake fluid.
A suitable brake fluid can be obtained from Authorised Service Centres.
Brake fluid level
The level of the brake fluid should always be between the MIN and MAX
marks, or above the MIN mark Ÿ.
It is not always possible to check the level of the brake fluid, as in some
models the engine components make it difficult to see the brake fluid reser-
voir. If you cannot read the exact brake fluid level, consult a specialist.
The brake fluid level drops slightly when the vehicle is being used due to wear
of the brake pads and the automatic readjustment of the brake.
Changing the brake fluid
The brake fluid should be changed in accordance with the instructions given
in the Maintenance Programme. Have the brake fluid changed by a qualified
workshop. SEAT recommends visiting a qualified workshop. This means that
only brake fluid complying with the required specifications will be used.
WARNING
If the brake fluid level is low or unsuitable/old brake fluid is used, the brake
system may fail or braking power will be reduced.
xCheck the brake system and the brake fluid level regularly!
xThe brake fluid should be changed regularly in accordance with the
instructions given in the Maintenance Programme.
Fig. 145 In the engine
compartment: brake fluid
reservoir, lid