instrument panel Seat Alhambra 2010 Owner's Guide

Cockpit73
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Main menuMFI display menu
The multifunction display (MFI) has two automatic memories: 1 - Partial
memory and 2 - Total memory. The selected memory will be shown in the
upper right-hand corner of the display.MenuFunctionSee
MFIInformation and possible configurations of the
multifunction display (MFI).Ÿpage 73
Audio
If the radio is on, the station is displayed.
In CD mode, the current CD is played.
ŸBooklet
“Radio” or
ŸBooklet
“navigation
system”
NavigationNavigation system information:
when the navigation to destination is on,
change of direction arrows and a proximity bar
are displayed. These symbols are similar to
those used in the navigation system.
If navigation to destination is not on, the direc-
tion of travel (compass) and the name of the
street on which you are driving are displayed.ŸBooklet
“Navigation
system”
Parking
heatingInformation and configurations of the parking
heating:
switching the parking heating on or off. Select
the operating mode and duration.Ÿpage 187
Vehicle
conditionCurrent warning or information texts.
This option only appears when one of the fol-
lowing texts is available. The number of availa-
ble messages is displayed. Example 1/1 or
2/2.Ÿpage 64
SettingsDifferent setting options, for example, the Con-
venience, Lighting & or Visibility menus, and
the time, speed warning with winter tyres, lan-
guage, units of measurement, or “Display off”.Ÿpage 75
With the ignition switched on, and memory 1 or 2 displayed, briefly press
to change from one memory to another.
1
Trip mem-
ory (for a
single jour-
ney).
The memory stores the values for the journey and the con-
sumption from the moment the ignition is switched on until
it is switched off again.
If the journey is broken for more than two hours, the mem-
ory is automatically erased. If the journey is continued in
less than two hours after the ignition is switched off, the
new data is added to the data already stored in the mem-
ory.
2Total mem-
ory (for all
journeys).
The memory records the values for a specific number of
partial trips, up to a total of 19 hours and 59 minutes or 99
hours and 59 minutes, or 1999.9 km (or miles) for 9999 km
(or miles), depending on the model of instrument panel.
On reaching either of these limits, the memory is automati-
cally erased and starts to count from 0 again.
OK

Cockpit 74
Possible displays
Changing between display modes
xIn vehicles without multifunction steering wheel: press the lever.
xVehicles with a multifunction steering wheel: press or .
Storing a speed for the speed warning
xSelect the display Speed warning at --- km/h.
xPress to store the current speed and switch off the warning.
xIn addition, set the required speed by pressing the rocker switch on the
windscreen wiper lever or buttons or on the multifunction steering
wheel for 5 seconds. Next, press again or wait a few seconds. The speed
is stored and the warning activated.
xTo switch off, press . The stored speed is deleted.
Manually erasing memory 1 or 2
xSelect the memory to be erased.
xPress and hold for approximately two seconds.
Personalising the displays
It is possible to select which of the displays in the multifunction display you
wish to see on the instrument panel in the settings menu. The units of meas-
urement can also be modified Ÿpage 75.
MenuFunction
Journey durationThis indicates the hours (h) and minutes (min) since
the ignition was switched on.
Current fuel
consumptionThe current fuel consumption while driving is dis-
played in l/100 km (or miles per gallon, mpg); when
the engine is running but the vehicle is not moving,
in l/h (or gallons per hour).
Average fuel
consumptionWhen the ignition is switched on, the average con-
sumption (in l/100 km or in mpg) is displayed after
the vehicle has moved approximately 100 metres
(328 feet). Otherwise horizontal lines are displayed.
The value shown is updated approximately every 5
seconds.
Distance to empty
(the distance you
can travel with the
remaining fuel)Approximate distance in km (or miles) that can still
be travelled with the fuel remaining in the tank,
assuming the same style of driving is maintained.
This is calculated using the current fuel consumption.
Distance coveredDistance travelled, after ignition is switched on, in km
(or miles).
Average speedAfter the ignition is switched on, the average speed
will be shown after a distance of approximately 100
metres (328 feet) has been travelled. Otherwise hori-
zontal lines are displayed. The value shown is
updated approximately every 5 seconds.
Digital display of
speedCurrent speed displayed digitally.
Oil temperature
digital displayUpdated engine oil temperature digital display
Speed warning
to --- km/hIf the stored speed is exceeded (between 30 - 250
km/h, or 18 - 155 mph), an audible warning is given
together with a visual warning.
MenuFunction
*+
OK
*+OK
OK
OK

Cockpit75
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Configuration Menu
Configuration
MenuFunction
Multifunction
display dataConfiguration of the multifunction display data which you
wish to see on the instrument panel display Ÿpage 73.
CompassChanging the magnetic region and calibration of the com-
pass. To calibrate the compass, please follow the instruc-
tions given on the instrument panel display.
ConvenienceChanging vehicle convenience functions Ÿpage 76.
Lights &
visibilityConfiguration of vehicle lighting Ÿpage 77.
TimeChanging the hours and minutes of the clock and the nav-
igation system. The time can be set here and the choice
can be made between the 24 hour and 12 hour display.
The S in the upper part of the display indicates that the
clock is set to summer time.
Winter tyresChanging the visual and audible speed warnings. This
function should only be used when the vehicle is fitted
with winter tyres, which are not designed for travel at
high speeds.
Settings:
LanguageChanging the language of the display texts and the navi-
gation system.
UnitsChanging the units of measurement for the temperature,
consumption and distance.
Second speedSwitching second speed display on and off
AutoholdSelecting whether the Auto-Hold function should remain
on permanently.
Travel modeChanging the headlamps for countries in which vehicles
are driven on the other side of the road. When the “mark”
is activated, the headlamps of a left-hand drive vehicle
are adjusted for driving on the left. The travel mode can
only be used for short periods of time.
ServiceCheck the service notifications or reset the service inter-
vals to zero
Manufacturer's
settings Some functions of the Configuration menu will be reset
to the factory value.
BackThe main menu is displayed again.
Configuration
MenuFunction

Unlocking and locking 92
Doors
Introduction
Additional information and warnings:
xVehicle key set Ÿpage 78
xCentral locking and locking system Ÿpage 83
xEmergency locking and unlocking Ÿpage 348
WARNING
If a door is not correctly closed, it could open unexpectedly when driving
and cause serious injuries.
xAlways stop immediately and close the door.
xWhen closing, ensure that the door has closed correctly. A closed door
should be flush with the corresponding parts of the bodywork.
xOpen and close doors only when nobody is in the way of the door.
WARNING
A door held open by its retainer could be blown closed by the wind or close
if the vehicle is on a hill causing injury.
xWhen opening and closing doors, always use the door handle.
Warning indicator
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
If a door is open or incorrectly closed, the indicator
 or o on the instrument
panel will light.
Depending on the vehicle equipment, a symbol may be displayed on the
instrument panel screen instead of the warning lamp. The indication is also
visible when the ignition is switched off. The indication disappears around 15
seconds after the vehicle has been locked.
Sliding doors
Introduction
Additional information:
xVehicle key set Ÿpage 78
xCentral locking and locking system Ÿpage 83
xEmergency locking and unlocking Ÿpage 348
lights upPossible causeSolution
oAt least one vehicle door is
open or not correctly shut.› Stop driving immediately!
Open the corresponding door
and close it immediately.

Unlocking and locking97
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Ta i l g a t e
Introduction
Additional information and warnings:
xCentral locking Ÿpage 83
xTransporting Ÿpage 13
xEmergency locking and unlocking Ÿpage 348
WARNING
Careless and unsuitable locking, opening and closing of the tailgate can
cause accidents and serious injury.
xOpen and close the tailgate only when nobody is in the way.
xDo not close the tailgate by pushing it down with your hand on the rear
window. The rear window could break and cause injury.
xEnsure the tailgate is locked after closing, otherwise, it may open unex-
pectedly while driving. A closed tailgate should be flush with the corre-
sponding parts of the bodywork.
xAlways keep the tailgate closed while driving to avoid toxic gases
entering the passenger compartment.
xDo not open the tailgate when there is a load carrier installed. Likewise,
the tailgate cannot be opened when a load is attached to it, for example
bicycles. An open tailgate could close itself if there is an additional weight
on it. If necessary, press down on the tailgate and remove the load.
xClose and lock both the tailgate and all the other doors when you are
not using the vehicle. Ensure that nobody remains inside the vehicle.
xNever allow children to play inside or around the vehicle without super-
vision, especially if the tailgate is open. Children could enter the luggage
compartment, close the tailgate and become trapped. Depending on the
time of the year, temperatures inside a locked and closed vehicle can be extremely high or extremely low resulting in serious injuries and illness or
even death, particularly for young children.
xNever leave children or disabled people alone in the vehicle. If the
vehicle key or the central locking button is used, they may be locked in the
vehicle.
Caution
Before opening the tailgate, ensure that there is sufficient free space to open
and close it, for example if you are towing a trailer or in a garage.
Warning indicator
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
A warning appears on the instrument panel
˜ if the tailgate is open or not
properly closed.
Depending on the vehicle equipment, a symbol may be displayed on the
instrument panel screen instead of the warning lamp. The indication is also
visible when the ignition is switched off. The indication disappears around 15
seconds after the vehicle has been locked.
lights upPossible causeSolution
˜The tailgate is open or not
correctly shut.› Stop driving immediately!
Open the tailgate and close it
again.
WARNING (continued)

Lights and visibility115
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Turn signal and main beam lever
Move the lever to the required position:
Right turn signal. Right-hand parking light (ignition switched off)
Ÿpage 117.
Left turn signal. Left-hand parking light (ignition switched off)
Ÿpage 117.
Main beam switched on Ÿ. The indicator lamp
 will light up on the
instrument panel.
Flashing the headlamps. The flashed beam comes on if the lever is
pressed. The indicator lamp
 will light up.
Push the lever all the way down to turn off the corresponding function.
Convenience indicators
For the convenience turn signals, move the lever as far as possible upwards
or downwards and release the lever. The turn signal will flash three times.
The control turn signals are switched on and off from the menu Lights&
Visibility on the instrument panel display Ÿpage 70. This function can be disconnected at a specialised workshop for those vehicles which do not have
the menu Lights & Visibility.
WARNING
Incorrect use of the headlamps may cause accidents and serious injury, as
the main beam may distract or dazzle other drivers.
Note
The turn signal only works when the ignition is switched on. The hazard
warning lights also work when the ignition is switched off Ÿpage 345.
Note
If a turn signal on the vehicle or trailer is faulty, the warning lamp flashes
twice as fast as usual.
Note
The main beam headlights can only be switched on if the dipped beam head-
lights are already on.
Fig. 66 Turn signal and
main beam lever.
A1
A2
A3
A4

Lights and visibility117
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xSwitching on the fog lights : Turn the switch to position  or pull out  to the first stop.
xSwitching on the rear fog light
: turn the light switch to position  o
pull out  to the maximum.
xTo switch off the fog lights, press the light switch or turn it to position /.
Audible warnings to advise the driver that the lights have not been switched
off
If the key is not in the ignition and the driver's door is open, an audible
warning signal is heard in the following cases: This is a reminder to turn off
the lights.
xWhen the parking light is on Ÿpage 115.
xWhen the light switch is in position .
WARNING
The side lights or daytime driving lights are not bright enough to illuminate
the road ahead and to ensure that other road users are able to see you.
xAlways use your dipped beam head lights if it is raining or if visibility is
poor.
Lights and visibility: functions
Parking light
When the parking light is switched on,(right or left turn signal), the front side
light and the rear light on the corresponding side of the vehicle stay lit. The
parking lights will only work with the ignition off.
Daytime driving light
The daytime driving light consists of individual lights in the front headlamps.When the daytime driving light is switched on, only the individual lights come
on Ÿ.
The daytime lights are switched on each time the ignition is turned on if the
light switch is in position
!, 5,4 or /.
When the light switch is in position
!, 5, 4 or /, a photo sensor goes out and
the instrument and switch lighting comes on automatically.
Automatic dipped beam control
!54/
The automatic dipped beam control is merely intended as an aid and is not
able to recognise all driving situations.
When the light switch is in position
!, 5, 4 or /, the vehicle lights and the
instrument panel and switch lighting switch on and off automatically in the
following situations Ÿ:
Activating the daytime lightsDeactivating the daytime lights
Press and hold the turn signal and
main beam lever upwards and back-
wards (right turn signal and light
flasher).Press and hold the turn signal and
main beam lever downwards and
backwards (left turn signal and light
flasher).
Switch the ignition on and off for approximately 3 seconds.
Automatic switching on:Automatic switching off or switch to
daytime lighting:
The photo sensor detects darkness,
for example, when driving through a
tunnel.When adequate lighting is detected.
When driving at more than 140 km/h
for a few seconds.When driving at less than 65 km/h
for a few minutes.
The rain sensor detects rain and acti-
vates the windscreen wipers.When the windscreen wiper has
been inactive for a few minutes.

Lights and visibility119
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
The headlights, rear lights and turn signals may mist up temporarily on the
inside in cool or damp weather. This is normal and in no way effects the useful
life of the vehicle lighting system.
Adhesive strips for headlights or adjusting headlights
In those countries where vehicles drive on the other side of the road to the
home country, the asymmetric dipped beam may dazzle drivers of oncoming
vehicles. Therefore, when driving abroad, adhesive strips should be attached
to the headlights or the headlights should be adjusted accordingly.
The direction of the headlights can be adjusted from the instrument panel, in
the menu Settings submenu Travel mode Ÿpage 70.
For those vehicles in which it is not possible to adjust the headlights from the
menu, adhesive strips are used to cover certain parts of the headlamp cover
or the headlights may be adjusted at a specialised workshop. For further
information, please refer to a specialised workshop. SEAT recommends
visiting a qualified workshop.
Note
The use of Travel mode and adhesive strips on the headlights is only author-
ised for a short period of time. To modify the direction of the headlamps more
permanently, please take the vehicle to a specialised workshop. SEAT recom-
mends visiting a qualified workshop.
Function “Coming home” and “Leaving home” (guidance
lights)
The “Coming home” function should be switched on manually. However the
“Leaving home” function is automatically controlled by a photo sensor.
Lighting around the exterior mirrors
The lighting around the exterior mirrors illuminates the door area on entering
and leaving the vehicles. It comes on when the vehicle is unlocked, when the
vehicle door is opened and when the “Coming home” or “Leaving home”
“Coming Home”Necessary operations
To switch sys-
tem on:
– Switch off the ignition.
– Briefly flash the headlights for approximately one sec-
ond Ÿpage 115.
The “Coming home” lighting comes on when the driver's
door is opened. The delay in switching off the headlights
is counted from when the last door or tailgate is closed.
The system
switches off:
– Automatically at the end of the delay period.
– Automatically, if 30 seconds after coming on, a vehicle
door or tailgate remains open.
– If the light switch is turned to position
/.
– If the ignition is switched on.
“Leaving home”Necessary operations
To switch sys-
tem on:– Unlock the vehicle when the light switch is in position
!54/ and the photo sensor detects darkness.
The system
switches off:
– Automatically, at the end of the delay period.
– When the vehicle is locked.
– When the light switch is turned to position
/.
– When the ignition is switched on.

Seats and storage compartments 162
Storage compartments
Introduction
Storage compartments must only be used to store light or small objects.
The front central armrest compartment houses the factory-fitted AUX-IN or
multimedia (MEDIA-IN) connection sockets.
The factory-fitted CD changer is located in the left-hand storage compartment
of the luggage compartment.
Additional information and warnings:
xChild seats (accessories) Ÿpage 42
xLuggage compartment Ÿpage 146
xCare and cleaning of the vehicle interior Ÿpage 278
xŸBooklet “Radio” or ŸBooklet “navigation system”
WARNING
In the event of sudden braking movements or turns, loose objects may be
thrown around the vehicle interior. This could cause serious injuries to
passengers and cause the driver to lose control of the vehicle.
xDo not transport animals or place hard, heavy or sharp objects inside
the vehicle in: open storage compartments, instrument panel, storage tray,
items of clothing or bags.
xWhile driving, always keep object compartments closed.
WARNING
Objects falling into the driver's footwell could prevent use of the pedals.
This could lead the driver to lose control of the vehicle, increasing the risk
of a serious accident.
xMake sure the pedals can be used at all times, with no objects rolling
underneath them.
xThe floor mat should always be secured to the floor.
xNever place other mats or rugs on top of the original mat supplied by
the factory.
xMake sure that no objects can fall into the driver's footwell while the
vehicle is in motion.
Caution
xObjects on the shelf could chafe against the wires of the heating element
in the rear window and cause damage.
xDo not keep heat-sensitive objects, food or medicines inside the vehicle.
Heat and cold could damage them or render them useless.
xLight-transparent objects placed inside the vehicle, such as lenses,
magnifying glasses or transparent suction caps on the windows, could
concentrate the sun's rays and cause damage to the vehicle.
Note
The ventilating slits between the heated rear window and the shelf must not
be covered so that used air can escape from the vehicle.
WARNING (continued)

Seats and storage compartments 164
Compartment on the instrument panel
The storage compartment on the instrument panel may have a cover.
To open, press the button on the cover Ÿfig. 110 (arrow).
To close, press the cover down until it clicks into place.
Compartment on the centre console
There is an open compartment on the centre console Ÿfig. 111 in which
there may be a 12 volt socket Ÿpage 175.
Fig. 110 Storage
compartment on the
instrument panel.Fig. 111 Compartment in
the front centre console.