instrument panel Seat Alhambra 2010 Service Manual

Driving 208
Driving down hills
The steeper the gradient, the lower the gear you will need. The lowest gears
increase the engine braking work. Never go down hills with the selector lever
in neutral N.
xYou should reduce speed accordingly.
xPress the selector lever from position D to the right into the Tiptronic
selector gate Ÿpage 207.
xGently pull the selector lever back to change down a gear.
xALTERNATIVELY: Reduce using the steering wheel paddles Ÿpage 207.
Emergency program
If all the selector lever positions on the instrument panel display are shown
with a light-coloured background, this means there is a fault in the system.
The automatic gearbox will operate in emergency programme mode. When
the emergency program is activated, it is possible to drive the vehicle
however, at low speeds and within a selected range of gears.
For the DSG
® dual clutch gearbox, in some cases, this may mean that reverse
gear does not engage. The gearbox should be checked by a qualified work-
shop as soon as possible.
Overload protection for the 6-speed DSG gearbox
®
When the clutch is overloaded, the vehicle begins to jerk and the selector
lever position indicator begins to flash. To prevent damage to the clutch, this
interrupts the power transmission between the engine and the gearbox.
There is no more traction and it is not possible to accelerate. If the clutch is
opened automatically due to overloading, press the brake pedal. Wait a few
seconds before starting to move again.
Kick-down
The kick-down system provides maximum acceleration when the gear
selector lever is in the positions D, S or in the Tiptronic position.When the accelerator pedal is pressed right down, the automatic gearbox will
shift down to a lower gear, depending on road speed and engine speed. This
takes advantage of the maximum acceleration of the vehicle Ÿ.
When the accelerator is pressed to the floor, the automatic gearbox shifts to
the next gear only after the engine reaches the specified maximum engine
speed.
Launch-Control Programme
The Launch-Control programme enables maximum acceleration while at a
standstill.
xDeactivating the TCS Ÿpage 210.
xPress and hold the brake pedal with your left foot.
xPlace the selector lever in position S or Tiptronic.
xPress the accelerator with the right foot until the vehicle reaches an
engine speed of approximately 3,200 rpm.
xLift the left foot off the brake Ÿ. The vehicle starts with maximum
acceleration.
xTurn on the TCS after accelerating!
WARNING
Rapid acceleration can cause loss of traction and skidding, especially on
slippery ground. This could cause loss of control of the vehicle resulting in
an accident and considerable damage.
xOnly use kick-down and rapid acceleration when weather conditions,
surface conditions and traffic conditions permit; accelerate and drive in a
manner that does not endanger other road users.
xPlease remember that the driven wheels can slip and the vehicle can
skid if the TCS is turned off, especially on slippery ground.
xTurn on the TCS after accelerating.

Driving209
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Caution
xIf you stop on a hill with a gear ratio engaged, do not try to prevent the
vehicle from rolling back by pressing on the accelerator. This could cause
overheating and damage the automatic gearbox.
xNever allow the vehicle to move with the gear selector lever in N, espe-
cially with the engine turned off. The automatic gearbox will not be lubricated
and could be damaged.
Recommended gear indication
In some vehicles, the recommended gear for reducing fuel consumption is
displayed on the instrument panel:
Information for cleaning the diesel particulate filter
The exhaust gas system control recognises when the diesel particulate filter
is blocked, and helps to clean it by recommending a specific gear for driving.
It may therefore be necessary to drive with the engine at an exceptionally high
speed Ÿpage 255.
WARNING
The recommended gear display is intended as a guideline only; it should
never replace the driver's attention to driving carefully.
xResponsibility for selecting the correct gear for each situation
continues to lie with the driver, for example when overtaking, climbing a
hill or towing a trailer.
For the sake of the environment
Selecting the most appropriate gear for the situation will help you to save
fuel.
Note
The recommended gear display is switched off when the clutch pedal is
pressed.
DisplayMeaning
ˆOptimum gear.
žRecommendation to change up a gear.
ŸRecommendation to change down a gear.
WARNING (continued)

Driving 212
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
WARNING
Driving with brakes in bad condition could result in a serious accident.
xIf the brake warning lamp H does not go out, or if it lights up when
driving, the brake fluid level in the reservoir is too low or there is a fault in
the brake system. Obtain professional assistance immediately
Ÿpage 219, “Brake fluid”.
xIf the brake warning lamp H lights up together with the ABS warning
lamp J, the regulation function of the ABS could be malfunctioning. As a
result, the rear wheels can lock relatively easily when braking. If the rear
wheels lock this could result in loss of vehicle control! If possible, reduce
your speed and drive carefully to a specialist workshop close by to check
the brake system. During the following journey, avoid sudden braking and
manoeuvres.
xIf the ABS warning lamp J does not go out or if it lights while driving,
the ABS is malfunctioning. The vehicle can only be stopped using normal
braking without ABS. The protection provided by the ABS is not available.
Visit a specialised workshop as soon as possible.
xIf I lights, alone or accompanied by a warning message on the instru-
ment panel screen, please go immediately to a specialist workshop to
check the brake pads and to replace them if they are worn.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Electronic parking brake
Applying the electronic parking brake
The parking brake can be applied whenever the vehicle is at a standstill, even
when the ignition is switched off. Always apply the parking brake when you
leave your vehicle and when you park.
xPull button until the control lamp G on the button lights up.
xThe parking brake is applied when the control lamp H lights up on the
instrument panel Ÿpage 211.
Releasing the electronic parking brake
xSwitch the ignition on.
Fig. 143 Detailed view of
the centre console: elec-
tronic parking brake
switch
G

Driving213
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xPress button . At the same time, press the brake pedal hard or gently
press the accelerator pedal with the engine switched on.
xThe control lamps G on the button and H on the instrument panel go
out.
Automatic release of the electronic parking brake on starting the engine
The electronic parking brake is automatically released when the vehicle starts
moving, if the driver's door is closed and the driver is wearing his/her seat
belt. In vehicles with a manual gearbox the clutch pedal should also be
pressed to the floor before starting the engine so that the system recognises
that the parking brake should be released.
Emergency braking function
Only use the emergency braking function if the vehicle cannot be stopped
with the brake pedal Ÿ!
xPull button hard to stop the vehicle. The warning display will be
accompanied by the corresponding warning chime.
xTo stop the braking process, release the button or press the accelerator.
WARNING
The incorrect use of the electronic parking brake may result in serious acci-
dent.
xNever use the electronic parking brake to brake the vehicle except in an
emergency. The braking distance is considerably longer, because braking
is only applied to the rear wheels. Always use the foot brake.
xNever accelerate from the engine compartment with the engine running
and a gear or a gear range engaged. The vehicle could move, even if the
parking brake is applied.
Note
In vehicles with a manual gearbox: When the clutch pedal is released and the
accelerator pressed at the same time, the electronic parking brake is auto-
matically released.
Note
If the vehicle battery is flat, it will not be possible to disconnect the electronic
parking brake. Use the jump-start Ÿpage 371.
Note
When the electronic parking brake is applied or released, noises may be
heard.
Note
If the electronic parking brake has not been used for a long while, the system
sometimes performs automatic and audible checks while the vehicle is at a
standstill.
Parking
When parking your vehicle, all legal requirements should be observed.
To park the vehicle
Complete operations only in the sequence given.
xPark the vehicle on a suitable surface Ÿ.
xPress and hold the brake pedal until the vehicle comes to a standstill.
xConnect the electronic parking brake Ÿpage 212.
xFor an automatic gearbox, move the selector lever to position P.
G
G

Driving223
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Auto Hold turns off automatically under the following conditions:
WARNING
The Auto Hold technology is limited by the laws of physics. The improved
comfort provided by Auto Hold should never prompt you to take risks.
xNever leave the vehicle running and with the Auto Hold function
switched on.
xAuto Hold cannot always stop the vehicle uphill and downhill (for
example, if the ground is slippery or frozen).
Caution
Before entering an automatic car wash, always switch the Auto Hold function
off, as it could be damaged when the electronic parking brake automatically
engages.
Start-Stop Function*
In Start-Stop mode, the engine is automatically switched off when the vehicle
is at a standstill. The engine restarts automatically when required.
The function is enabled automatically whenever the ignition is switched on.
The instrument panel displays information on the current status.
Vehicles with a manual gearbox
xWhen the vehicle is at a standstill, leave it in neutral and take your foot off
the clutch. The engine switches off.
xSimply depress the clutch pedal to move off again.
Vehicles with an automatic gearbox
xWhen the vehicle is at a standstill, depress the brake or keep it pressed
down. The engine switches off.
xThe engine will start again as soon as you release the brake pedal.
xWith the gear lever set to P, the engine will not start until a range of gears
is selected or the accelerator pedal is depressed.
manual gearboxAutomatic gearbox
1.If one of the conditions mentioned in table on page 222 changes.
2.If the engine is not running regularly or if there is a malfunction.
3.When changing to idle speed.If the selector lever is placed in
neutral (N).
4.If the engine is turned off or stalls.If the engine is switched off.
5.If the driver accelerates while
pressing the clutch in.If the vehicle is accelerated.
6.When one of the wheels has mini-
mal contact with the ground (for
example, on uneven ground).
Fig. 147 Detailed view of
the centre console: Start-
Stop function button.

Driving 224
Important conditions for the engine to automatically switch off
xThe driver seat belt must be buckled.
xThe driver door must be closed.
xThe bonnet must be closed.
xThe factory-fitted towing bracket must not be electrically connected to a
trailer.
xA minimum engine temperature has been reached.
xThe vehicle has moved since the last stop.
xIn vehicles with Climatronic: The temperature inside the vehicle is within
the preset temperature range.
xThe temperature set is neither very high nor very low.
xThe air conditioning defrost function is not switched on.
xIn vehicles with Climatronic: the blower has not been manually set to a
high speed.
xThe power level of the vehicle's battery is sufficient.
xThe vehicle's battery temperature is neither too high nor too low.
xThe vehicle is not on a steep gradient or slope.
xThe front wheels are not overly turned.
xThe heated windscreen is not switched on.
xReverse gear is not engaged.
xThe park assist system is not switched on.
Conditions for automatically restarting the engine
The engine may automatically restart under the following conditions:
xIf the vehicle interior is too hot or too cold.
xIf the vehicle moves.
xIf the vehicle's battery voltage drops.
Conditions requiring the key to restart the engine
The engine must be started using the key under the following conditions:
xIf the driver unbuckles his/her seat belt.
xIf the driver's door is opened.
xIf the bonnet is opened.
xIn vehicles with a manual gearbox: If a gear has been selected.
Switching Start-Stop mode on and off manually
xPress the button on the centre console Ÿpage 223, fig. 147.
xThe button will light up when the Start-Stop function is switched off.
The engine will start immediately if the vehicle is in Stop mode when it is
switched off manually.
WARNING
The brake servo and the power steering do not work when the engine is
switched off.
xNever allow the vehicle to move when the engine is switched off.
Caution
Using the Start-Stop function for a long period at very high outdoor tempera-
tures could damage the vehicle's battery.
Note
In some cases, you may have to restart the vehicle using the key. Observe the
corresponding message on the instrument panel display.
›

Driving 230
xWhen cleaning the sensors with high-pressure or steam cleaning equip-
ment, spray the sensors briefly at a distance of no less than 10 cm.
Note
Contact a specialist workshop with any system faults. SEAT recommends
visiting a qualified workshop.
Parking using the park assist system
Fig. 153 Gap detected: Engage the reverse gear to park (parallel or nose/tail to the
kerb).
Preparing to park
xThe Traction control system (TCS) must be turned on Ÿpage 210.
xParallel parking: press the button at speeds up to 50 km/h once.
When the function is enabled, the button Ÿfig. 152 will light up.
xPerpendicular parking: press the button at speeds up to 50 km/h
twice. When the function is enabled, the button Ÿfig. 152 will light up.
xIf necessary, press the button once more to change parking mode.
xApply the turn signal indicator for the side on which a gap is to be
detected for parking. The instrument panel displays the side corresponding
to the road.
Parking
xParking parallel to the road: Drive next to the gap at a speed of no more
than 40 km/h and at a distance of between 0.5 m and 2 m.
Fig. 152 Detailed view of
the centre console: button
to switch the park assist
system on manually.i
i
i

Driving231
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xParking perpendicular to the road: Drive next to the gap at a speed of no
more than 20 km/h and at a distance of between 0.5 m and 2 m.
xThe best parking results will be achieved if you position the vehicle as
parallel as possible to the line of parked cars or the kerb.
xWhen a suitable parking place is displayed on the instrument panel, stop
and select reverse gear.
xFollow the instructions given on the instrument panel display
xThen, release the steering wheel when the warning signal sounds Ÿ:
The system will move the steering wheel! Observe the surrounding area.
xObserve the surrounding area and accelerate carefully at a maximum of
up to 7 km/h.
xThe park assist system is only responsible for moving the steering wheel
during the manoeuvre. The driver applies the accelerator, the clutch, the
gears and the brake.
xFollow the instructions given by the park assist system until the
manoeuvre is completed.
xThe park assist system steers the vehicle forwards and backwards until it
is in a straight position in the parking space.
xThe manoeuvre is complete when the corresponding indication is given
on the instrument panel display.
Stopping the parking manoeuvre
The park assist system stops the manoeuvre in the event of one of the
following:
xPress button .
xDriving faster than 7 km/h.
xThe driver moves the steering wheel.
xThe parking manoeuvre has not been completed after six minutes since
the park assist system was activated.
xA sliding door is opened. To restart the manoeuvre, close the sliding door
and press the button again.
xThere is a system malfunction (system temporarily unavailable).
xThe TCS system is switched off or the TCS or ESP is working.
WARNING
The steering wheel turns quickly by itself when parking using the park
assist system. Placing your hand between the steering wheel spokes could
lead to injuries.
Note
The park assist system has its limitations. For example, it is not possible to
park on tight bends using the park assist system.
Note
Even if the park assist system recognises that there is not enough space for
parking the vehicle, the display screen on the instrument panel will still
display this place. In this case, the parking manoeuvre should not be
requested.
Note
Changing gears between forward and reverse gears before indicated (that is,
before the signal from the parking sensor system) the parking results may not
be ideal.
Note
For parallel parking (parallel to the road), a sound will tell the driver when
they must change from forward gears to reverse; the signal from the parking
sensor system does not indicate changes of direction.
i
i

Driving 232
Note
The park assist can also be activated afterwards, if you pass close to a parallel
parking space at a maximum of 40 km an hour or close to be perpendicular
parking space at about 20 km an hour then press the button .
Note
The progress bar on the screen of the instrument panel shows a display of the
relative distance to be covered.
Note
When the Park Assist system is turning the steering wheel of the stopped
vehicle the symbol K is also displayed. Press on the brake pedal so that the
steering can turn with the vehicle at a standstill and thus reduce the number
of manoeuvres.
Note
A suitable parking space length is at least 1.1 m greater than the length of the
vehicle.
Note
If the results of the park assist system are not as good after changing the
wheels, the system must memorise the perimeter of the new wheels. This
process is performed automatically while the vehicle is in motion. To help this
process, turn slowly (at less than 20 km/h), e.g. in an empty car park.
Leaving a parking space using the Park Assist system
Driving off
xSwitch on the engine.
xPress button . When the function is enabled, the button Ÿpage 230,
fig. 152 will light up.
xApply the turn signal indicator for the side on which you want to leave the
parking space.
xSelect reverse gear.
xFollow the instructions given by the park assist system.
xWhen the next indication appears, release the steering wheel Ÿ in
“Parking using the park assist system” on page 230: The system will move
the steering wheel! Observe the surrounding area.
xObserve the surrounding area and accelerate carefully at a maximum of
up to 7 km/h.
xThe park assist system is only responsible for moving the steering wheel
during the manoeuvre. The driver applies the accelerator, the clutch, the
gears and the brake.
xWhen it is possible to leave the parking space, the Park Assist system will
stop. Take control of the steering and when traffic conditions permit, leave
the parking space.
Automatic stoppage of the manoeuvre
The park assist system stops the manoeuvre in the event of one of the
following:
xDriving faster than 7 km/h.
xThe driver moves the steering wheel.
xA sliding door is opened. To restart the manoeuvre, close the sliding door
and press the button again.
xThere is a system malfunction (system temporarily unavailable).
xThe TCS system is switched off or the TCS or ESP is working.
ii
i

Driving 240
Warning and control lamp
Fig. 158 Dash panel display: CCS status indications.
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Display
There are different versions of the cruise control system. In vehicles with the
multifunction display (MFI), the set speed is displayed on the instrument
panel screen.Status fig. 158:
CCS temporarily switched off. The set speed is displayed in small figures.
System error. Contact a specialist workshop.
CCS switched on. The speed memory is empty.
The CCS is switched on. The set speed is displayed in large figures.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
lights upPossible causeSolution
%
This cruise control system
maintains the set speed of
the vehicle.–
AA
AB
AC
AD