ignition Seat Exeo ST 2012 Owners Manual

278If and when
Changing the side light bulb (outside of vehicle)
The procedure for changing the bulb is the same on both
sides.
Fig. 212 Side light bulb
(outside of vehicle)
Fig. 213 Side light bulb
(outside of vehicle)
– Switch off the ignition and the lights. –
Raise the bonnet.
– Move the brace ⇒ Fig. 212 1
in the direction of the arrow and
remove the rigid cover, separating the brace side and then re-
moving the two tabs from the other end of the cover.
– Gently press on the bulb holder tabs ⇒ Fig. 213 and pull the
cover upwards (it can also be removed by pulling on the bulb
holder wires).
– Separate the bulb from the bulb holder by pulling both pieces
anticlockwise.
– Fit the new bulb by pressing on the bulb holder.
– Insert the bulb into the socket and press on the bulb holder. Fit
the cover, first inserting the side tabs and then closing the cov-
er and the brace. Make sure that the gasket sits well on the cas-
ing cover during the operation.
– Check whether the new bulb is working. 

279
If and when
Changing the side light bulb (inside of vehicle)
The procedure for changing the bulb is the same on both
sides.
Fig. 214 Side light bulb
(inside of vehicle)
Fig. 215 Side lights.
Bulb holder grip in verti-
cal position
– Switch off the ignition and the lights. –
Raise the bonnet.
– Move the brace ⇒ Fig. 214 1
in the direction of the arrow and
remove the rigid cover, separating the brace side and then re-
moving the two tabs from the other end of the cover.
– Remove the bulb and the bulb holder by pulling on the bulb
holder wiring.
– Separate the bulb from the bulb holder by pulling both pieces
anticlockwise.
– Fit the new bulb by pressing on the bulb holder.
– Insert the bulb into the socket so that the side of the bulb hold-
er grip is vertical ⇒ Fig. 215 and press on it.
– Fit the cover, first inserting the side tabs and then closing the
cover and the brace. Make sure that the gasket sits well on the
casing cover during the operation.
– Check whether the new bulb is working. 
Changing bulbs. Bi-Xenon AFS headlights Types of bulbs
Changing bulbs requires a certain degree of practical skill
You can change the following bulb for the exterior lights yourself:
● Bulb for headlights: Indicator light 12V/21W (PY21W)
The following bulbs should only be changed by a specialised workshop:
Safety FirstOperating InstructionsPractical TipsTechnical Specifications

280If and when
● Main headlight lamps: Xenon ⇒ 
lights.
● Sources of the DRL (daylight) light unit and position.
WARNING
● Take particular care when working on components in the engine com-
partment if the engine is warm - risk of burns!
● Bulbs are highly sensitive to pressure. The glass can break when you
touch the bulb, causing injury.
● The high voltage element of gas discharge bulbs* (xenon light) must
be handled correctly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not to injure yourself on sharp
parts in the headlight housing.
CAUTION
● Remove the ignition key before working on the electric system. If not, a
short circuit could occur.
● Switch off the lights or parking lights before you change a bulb.
For the sake of the environment
Please ask your specialist retailer how to dispose of used bulbs in the prop-
er manner.
Note
● Depending on weather conditions (cold or wet), the front lights, the fog
lights, the tail lights and the turn signals may be temporarily misted. This
has no influence on the useful life of the lighting system. By switching on
the lights, the area through which the beam of light is projected will quickly
be demisted. However, the edges may continue to be misted.
● Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning properly. This is not only in the inter-
est of your own safety, but also in that of all other road users. ●
Before changing a bulb, make sure you have the correct new bulb.
● Do not touch the glass part of the bulb with your bare hands, use a cloth
or paper towel instead. Otherwise, the fingerprints left on the glass will va-
porise as a result of the heat generated by the bulb, be deposited on the
reflector and impair its surface. 
Removing the air duct
The air duct has to be removed to gain access to the bulbs
for the right-side headlight.
Fig. 216 Air duct on
right side of vehicle
– Unscrew bolts A
⇒ Fig. 216.
– Detach air duct from guide B
and take it out. 

282If and when
Changing the turn signal bulb
The procedure for changing the bulb is the same on both
sides.
Fig. 219 Turn signal
Fig. 220 Turn signal
– Switch off the ignition and the lights. –
Raise the bonnet.
– Pull the rubber cap ⇒ Fig. 219 to remove it.
– Remove the bulb holder by pulling on the grip and turning it an-
ticlockwise ⇒ Fig. 220.
– Replace the blown bulb in the bulb holder (press and turn anti-
clockwise to remove) with a new bulb (press and turn clockwise
to insert).
– Insert the bulb holder into the socket with the tab facing up-
wards and the grip horizontal. Press it against the socket and
turn clockwise. When changing the bulb, you can check the po-
sition of the bulb through the headlight glass.
– Fit the rubber cap and tighten, making sure it fit properly into
the headlight casing.
– Check whether the new bulb is working. 
Changing the xenon bulb
The procedure for changing the bulb is the same on both sides.
WARNING
This type of bulb should be changed at a specialised workshop.


294If and when
Jump leads
Jump leads must comply with standard DIN 72553 (see manufacturer's doc-
umentation). The wire cross section must be at least 25 mm 2
for petrol en-
gines and at least 35 mm 2
for diesel engines.
Note
● The vehicles must not touch each other, otherwise electricity could flow
as soon as the positive terminals are connected.
● The discharged battery must be properly connected to the vehicle elec-
trical system. 
How to jump start: description
Fig. 244 Diagram of con-
nections for vehicles
without Start-Stop sys-
tem
Fig. 245 Diagram of con-
nections for vehicles
with Start-Stop system
Jump lead terminal connections
1. Switch off the ignition of both vehicles ⇒ 
.
2. For vehicles without Start-Stop system :
– Connect one end of the red jump lead to the positive +
termi-
nal of the vehicle with the flat battery A ⇒ Fig. 244.
– Connect the other end of the red jump lead to the positive ter-
minal +
in the vehicle providing assistance B.
– Connect one end of the black jump lead to the negative terminal
–
of the vehicle providing assistance B ⇒ Fig. 244.
– Connect the other end of the black jump lead X
to a solid met-
al component bolted to the engine block or to the engine block
itself of the vehicle with the flat battery. However, connect it to
a point as far as possible from the battery A
.
3. For vehicles with Start-Stop system :

297
If and when
Towing and tow-starting
Tow-starting
The use of jump leads is preferable to tow-starting.
We recommend that you do not tow-start your vehicle. Jump-start-
ing is preferable ⇒ page 293.
However, if your vehicle has to be tow-started:
– Engage the 2nd or the 3rd gear.
– Keep the clutch pressed down.
– Switch the ignition on.
– Once both vehicles are moving, release the clutch.
– As soon as the engine starts, press the clutch and move the
gear lever into neutral. This helps to prevent driving into the
towing vehicle.
WARNING
The risk of accidents is high when tow-starting. The vehicle being towed
can easily collide with the towing vehicle.
CAUTION
When tow-starting, fuel could enter the catalytic converter and damage it. General notes
Please observe the following points if you use a tow rope:
Notes for the driver of the towing vehicle
–
Drive slowly at first until the tow rope is taut. Then accelerate
gradually.
– Begin and change gears cautiously. If you are driving an auto-
matic vehicle, accelerate gently.
– Remember that the brake servo and power steering are not
working in the vehicle you are towing. Brake sooner than nor-
mal and pressing the pedal gently.
Notes for the driver of the towed vehicle
– Ensure that the tow rope remains taut at all times when towing.
Tow rope or tow bar
It is easier and safer to tow a vehicle with a tow bar. You should only use a
tow rope if you do not have a tow bar.
A tow rope should be slightly elastic to reduce the loading on both vehicles.
It is advisable to use a tow rope made of synthetic fibre or similarly elastic
material.
Attach the tow rope or the tow bar only to the towing eyes provided or a tow-
ing bracket.
Driving style
Towing requires some experience, especially when using a tow rope. Both
drivers should be familiar with the technique required for towing. Inexper-
ienced drivers should not attempt to tow. 
Safety FirstOperating InstructionsPractical TipsTechnical Specifications

298If and when
Do not pull too hard with the towing vehicle and take care to avoid jerking
the tow rope. When towing on an unpaved road, there is always a risk of
overloading and damaging the anchorage points.
The ignition of the vehicle being towed must be switched on to prevent the
steering wheel from locking and also to allow the use of the turn signals,
horn, windscreen wipers and washers.
As the brake servo does not work if the engine is not running, you must ap-
ply considerably more pressure to the brake pedal than you normally would.
As the power assisted steering does not work if the engine is not running,
you will need more strength to steer than you normally would.
Towing vehicles with an automatic gearbox
● Put the selector lever into position “N”.
● Do not drive faster than 50 km/h.
● Do not tow further than 50 km.
● If a breakdown vehicle is used, the vehicle must be towed with the front
wheels raised.
Note
● Observe legal requirements when towing or tow-starting.
● Switch on the hazard warning lights of both vehicles. However, observe
any regulations to the contrary.
● For technical reasons, vehicles with an automatic gearbox must not be
tow-started.
● If damage to your vehicle means that there is no lubricant in the gear-
box, you must raise the drive wheels while the vehicle is being towed.
● If the vehicle has to be towed more than 50 km, the front wheels should
be raised during towing, and towing should be carried out by a qualified
person. ●
The steering wheel is locked when the vehicle has no electrical power.
The vehicle must then be towed with the front wheels raised. Towing should
be carried out by a qualified person.
● The towing eye should always be kept in the vehicle. Please refer to the
notes ⇒ page 297, Tow-starting. 
Front towing eyeFig. 246 Fitting the tow-
ing eye to front rear of
the vehicle
Fitting the towing eye
– Take the towing ring from the on-board tool set.
– Remove the front cover by pressing down on the right hand
side.
– Bolt the eye to its limit to the left, in the direction of the arrow
⇒ Fig. 246 

Index
Numbers and Symbols
230 V socket . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
A
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Adaptive headlights . . . . . . . . . . . . . . . . . . . . . 123 Faulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Airbag Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 68
Airbag covers . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Curtain airbags . . . . . . . . . . . . . . . . . . . . . . . 42
Front airbags . . . . . . . . . . . . . . . . . . . . . . . . 33
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . . 39
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 31
Air conditioner 2C-Climatronic . . . . . . . . . . . . . . . . . . . . . . 162
Air distribution . . . . . . . . . . . . . . . . . . . . . . 169
Air outlets . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Air purity sensor . . . . . . . . . . . . . . . . . . . . . 167
Air recirculation . . . . . . . . . . . . . . . . . . . . . 166
Air recirculation (automatic) . . . . . . . . . . . 167
Automatic mode . . . . . . . . . . . . . . . . . . . . . 165
Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . 166
ECON Mode (economy) . . . . . . . . . . . . . . . 166 Economical use . . . . . . . . . . . . . . . . . . . . . 170
Key settings . . . . . . . . . . . . . . . . . . . . . . . . 170
Solar-powered blower/sunroof . . . . . . . . . 170
Temperature selection . . . . . . . . . . . . . . . . 165
Air duct Fitting . . . . . . . . . . . . . . . . . . . . . . . . . 274, 281
Removing . . . . . . . . . . . . . . . . . . . . . . 274, 280
Air purity sensor . . . . . . . . . . . . . . . . . . . . . . . . 167
Alcantara . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Alternator Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 72
Ambient lighting . . . . . . . . . . . . . . . . . . . . . . . 126
Anti-lock brake system How it works . . . . . . . . . . . . . . . . . . . . . . . . 196
Anti-theft alarm system . . . . . . . . . . . . . . . . . . 110 Interior monitoring . . . . . . . . . . . . . . . . . . . 111
Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
Aquaplaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
Armrest Storage compartment in front armrest . . . 143
Armrests Adjusting the front armrest . . . . . . . . . . . . 143
Ashtray Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
ASR How the system works . . . . . . . . . . . . . . . . 197
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 71
Athermic windscreen . . . . . . . . . . . . . . . . . . . . 229 Auto-check system . . . . . . . . . . . . . . . . . . . . . . . 78
Automatic car wash tunnel . . . . . . . . . . . . . . . 217
Automatic gearbox
Dynamic gear control programme . . . . . . . 191
Kick-down feature . . . . . . . . . . . . . . . . . . . . 191
multitronic® . . . . . . . . . . . . . . . . . . . . . . . . 187
Paddle levers (tiptronic mode) . . . . . . . . . 193
Safety interlock for ignition key . . . . . . . . . 173
Selector lever lock . . . . . . . . . . . . . . . . . . . 190
Selector lever positions . . . . . . . . . . . . . . . 189
Steering wheel with paddle levers . . . . . . 193
tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
tiptronic mode . . . . . . . . . . . . . . . . . . . . . . 192
Automatic headlight control . . . . . . . . . . . . . . 117
Auxiliary heater . . . . . . . . . . . . . . . . . . . . . . . . 171
B
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245 Battery voltage . . . . . . . . . . . . . . . . . . . . . . . 84
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Disconnection . . . . . . . . . . . . . . . . . . . . . . . 246
Long periods of non-use . . . . . . . . . . 245, 246
Replacing . . . . . . . . . . . . . . . . . . . . . . 245, 246
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Winter operation . . . . . . . . . . . . . . . . 245, 246
Bicycle rack Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Biodiesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
Biodiesel fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 232
313
Index

Heated seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
High pressure cleaners . . . . . . . . . . . . . . . . . . 218
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
How to jump start description . . . . . . . . . . . . . 294
I
Identification number . . . . . . . . . . . . . . . . . . . 301
Identification plate . . . . . . . . . . . . . . . . . . . . . . 301
Ignition key Safety interlock . . . . . . . . . . . . . . . . . . . . . . 173
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Indicator lamps Glow plug system . . . . . . . . . . . . . . . . . . . . . 72
Main beam headlights . . . . . . . . . . . . . . . . . 72
Indicator lamps - overview . . . . . . . . . . . . . . . . . 67
Instruments Lighting . . . . . . . . . . . . . . . . . . . . . . . . . 64, 121
Interior lights Ambient lighting . . . . . . . . . . . . . . . . . . . . 126
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Luggage compartment . . . . . . . . . . . . . . . . 127
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Interior mirror With manual anti-dazzle setting . . . . . . . . 132
Interior monitoring . . . . . . . . . . . . . . . . . . . . . . 111
Intermittent wipe . . . . . . . . . . . . . . . . . . . . . . . 129
ISOFIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
J
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259, 264 Jump-starting . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Jump leads . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
K
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Air conditioner settings . . . . . . . . . . . . . . . 170
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Remote control key . . . . . . . . . . . . . . . . . . . 108
Settings for the driver seat . . . . . . . . . . . . 141
Kick-down feature . . . . . . . . . . . . . . . . . . . . . . . 191
L
Lamps Cruise speed . . . . . . . . . . . . . . . . . . . . . . . . . 69
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Instruments . . . . . . . . . . . . . . . . . . . . . 64, 121
Lights Adaptive headlights . . . . . . . . . . . . . . . . . . 123
Automatic headlight control . . . . . . . . . . . 117
Coming home function . . . . . . . . . . . . . . . 119
Cornering light . . . . . . . . . . . . . . . . . . . . . . 123
Dipped beam headlights faulty . . . . . . . . . . 85
Dynamic headlight range control . . . . . . . 122
Headlight flasher . . . . . . . . . . . . . . . . . . . . 125
Leaving home function . . . . . . . . . . . . . . . 119
Parking light . . . . . . . . . . . . . . . . . . . . . . . . 125
Reverse lights faulty . . . . . . . . . . . . . . . . . . . 85
Switching on and off . . . . . . . . . . . . . . . . . 117
Xenon lights . . . . . . . . . . . . . . . . . . . . . . . . 122 Load compartment in the luggage compart-
ment
see Loading the luggage compartment . . . 16
Loading the luggage compartment . . . . . . . . . . 16
Locking the doors manually if the central lock- ing fails to work
Locking the doors manually if the centrallocking fails to work . . . . . . . . . . . . . . . . 105
Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Long periods of non-use Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Luggage compartment . . . . . . . . . . . . . . . . . . . 144 Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Extending . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Fastening rings . . . . . . . . . . . . . . . . . . . . . . 145
Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Luggage compartment liner . . . . . . . . . . . 149
Luggage net . . . . . . . . . . . . . . . . . . . . . . . . 145
Net partition . . . . . . . . . . . . . . . . . . . . . . . . 147
Retaining strap . . . . . . . . . . . . . . . . . . . . . . 146
Side storage compartment . . . . . . . . . . . . 150
Ski bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
see also Loading the luggage compartment . .16
Luggage compartment cover Removing . . . . . . . . . . . . . . . . . . . . . . . . . . 148
M
Main beam headlights . . . . . . . . . . . . . . . 117, 124
Maintenance Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Maintenance and cleaning . . . . . . . . . . . . . . . 216
317
Index