Seat Leon 5D 2005 Owner's manual

If and when229
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
11
Vacant
12 Gateway 5
13 Petrol injection module supply
25
Diesel injection module supply 30
14 Coil 20
15 Engine T71 / 20 FSI
5
Pump relay 10
16 ADS pump 30
17 Horn 15
18 Vacant
19 Clean 30
20 Vacant
21 Lambda probe 15
22 Brake pedal, speed sensor 5
23 Engine 1.6, main relay (relay n° 100)
5
T 71 diesel EGR 10
2.0 D2L High-pressure fuel pump 15
24 ARF, change valve 10
25 Right lighting 40
26 Left lighting 40
1.6 SLP engine 40
1.9 TDI Glow plug relay 50
28 KL15 40
Number
Electrical equipment Amperes
leon_ingles Seite 229 Donnerstag, 20. Oktober 2005 12:14 12

If and when
230Position in engine compartment: side boxFuses
Some of the electrical items listed in the table are only fitted on certain
models or are optional extras.
Please note that the above list, while corr ect at the time of printing, is subject
to alterations. 29
Electric windows (front and back)
50
Electric windows (front) 30
30 Contact relief-relay 40
Number Electrical equipment Amperes
B1 Alternator < 140 W
150
Alternator > 140 W 200
C1 Power steering 80
D1 Multi-terminal voltage supply “30”. Internal fuse box 100
E1 Ventilator < 500 W / Ventilator > 500 W 50 / 80
F1 PTCs (Supplementary electrical heating using air) 100
G1 Trailer fuse voltage supply in internal fuse box 50
H1 Central locking control unit (4F8 with autolock)
Number
Electrical equipment Amperes
leon_ingles Seite 230 Donnerstag, 20. Oktober 2005 12:14 12

If and when231
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Bulb changeGeneral notesBefore changing any bulb first turn off the equipment concerned.
Do not touch the bulb glass. Fingerprints vaporise in the heat, causing a
reduction in the bulb life and condensation on the mirror surface, thus
reducing efficiency.
A bulb should only be replaced by one of the same type. The type is inscribed
on the bulb, either on the glass part or on the base.
It is highly recommended to keep a box of spare bulbs in the vehicle. At the
very least, the bulbs that most affect road safety should have spares in the
vehicle.
Main headlights
Dipped beam - H7
Full lights - H1
Front side ligths - W5W
Indicator - PY21W
Xenon headlights
19)
Dipped beam and full lights - D1S
20)
Light burst and additional full lights - H1
Front side lights - W5W
Indicators - PY21W Fog lights
Fog lights - H3
Fixed rear light
Stop/Rear side lights - P21W
21)
Indicator - P21W
Rear tailgate light
Fog light (driver side) - P21W
Reverse gear light (passenger side) - P21W
Rear side lights - W5W
Indicator
Side indicator - W5W
Registration plate light
Registration plate light - C5W
Note
•
Due to the difficulty in accessing the lamps, these must be changed by an
Authorised Service Centre. However, the following is a description of how to
change the bulbs except for the fog lights and interior bulbs.
19)For these type of headlights, the bulbs must be changed by an Authorised Service
Centre, given that complex elements of the vehicle must be removed and that the au-
tomatic control system must be reset.20)Xenon bulbs discharge emit 2.5 times as much light flux and have a useful life five
times greater than halogen bulbs.
21)Electronically controlled single filament bulb for Stop/Side bulbs. If the bulb blows
it will not work or Stop position.
leon_ingles Seite 231 Donnerstag, 20. Oktober 2005 12:14 12

If and when
232Main headlight lamps
Turn signals
Dipped headlights
Main beam headlights
Side lights
Turn sig nal lam ps–Raise the bonnet.
– Rotate the lamp holder ⇒fig. 155 to the left and pull.
– Remove the bulb by pressing on the lamp holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Fig. 154 Main headlight
lamps
AAABACAD
Fig. 155 Turn signal
lamps
AA
leon_ingles Seite 232 Donnerstag, 20. Oktober 2005 12:14 12

If and when233
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Dipped beam lights–Raise the bonnet – Remove the loops
⇒fig. 156 in the direction of the arrow and
remove the cover.
– Remove the connector ⇒fig. 157 from the lamp.
– Disengage the retainer spring ⇒fig. 157 pressing inwards
and to the right.
– Extract the bulb and fit the repl acement so that the rim of the
attachment plate is on the reflector cut-out.
Fig. 156 Dipped head-
lightsFig. 157 Dipped head-
lights
A1
A2
A3
leon_ingles Seite 233 Donnerstag, 20. Oktober 2005 12:14 12

If and when
234Main beam lights– Raise the bonnet.
– Remove the cover ⇒fig. 158 by pulling on this. – Remove the connector
⇒fig. 159 from the bulb.
– Press the spring ⇒fig. 159 inwards and to the right.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.
Fig. 158 Main beam
headlightsFig. 159 Main beam
headlights
AC
A1
A2
leon_ingles Seite 234 Donnerstag, 20. Oktober 2005 12:14 12

If and when235
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Side lights–Raise the bonnet.
– Remove the cover ⇒fig. 160 by pulling on this. – Extract the lamp holder
⇒fig. 161 outwards.
– Replace the bulb by pulling this out and inserting the replace- ment.
– Installation is done in the reverse order.
Rear lights•
On the bodywork
- Indicator, side lights and brake lights
•
On the tailgate
- Left hand side: side and fog light.
- Right hand side: side and rear light.
Fig. 160 Side lightsFig. 161 Side lights
AD
A1
leon_ingles Seite 235 Donnerstag, 20. Oktober 2005 12:14 12

If and when
236Indicator, side and brake lights on the bodywork– Press on the side pin outwards and take out the lamp holder.
– Extract the failed bulb and change it for a new one.
– To refit follow the steps in reverse order, taking special care when
fitting the lamp holder.
Position light, fog light and reverse light on the tailgate–Open the tailgate.
– Pull the cover off. See the arrow ⇒fig. 163 .
Fig. 162 Side position
and brake lights on the
bodywork
Fig. 163 Lights on the
tailgateFig. 164 Removing the
lampholder
leon_ingles Seite 236 Donnerstag, 20. Oktober 2005 12:14 12

If and when237
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
– Take the lampholder out pressing on the securing pins and
extract it outwards ⇒ page 236, fig. 164.
– Replace the faulty lamp, rotating it to the left and outwards.
– Installation is done in the reverse order.Side indicators– Press the indicator on one of its sides to take it out.
– Remove the lamp holder from the indicator.
– Remove the failed glass bulb and replace with a new bulb.
– Insert the lamp holder in the indicator guide until it clicks into place. – First place the indicator in the opening in the bodywork, fixing
the tabs ⇒fig. 165, arrow .
– Insert the lamp as shown by the arrow ⇒fig. 165 .
Fig. 165 Side turn indi-
cator
A1
A2
leon_ingles Seite 237 Donnerstag, 20. Oktober 2005 12:14 12

If and when
238Luggage compartment lights– Extract the tulip shaped fitting by pressing on the inside edge of
this -arrow- using the flat si de of a screwdriver ⇒ fig. 166. – Press the lamp sideways and remove it from its housing
⇒ fig. 167.
– Installation is done in the reverse order.
Fig. 166 Luggage
compartment lightFig. 167 Luggage
compartment light
leon_ingles Seite 238 Donnerstag, 20. Oktober 2005 12:14 12