display Seat Leon SC 2013 SOUND SYSTEM 2.0

2General informationGeneral informationThis manual contains information, recommendations, advice and warningsrelated to your radio system. The other publications in the vehicle documen-tation contain further information of which you should be aware for yourown safety and for that of your passengers.
Ensure that the onboard documentation is kept in the vehicle at all times.This is especially important when lending or selling the vehicle to anotherperson.
This manual contains a description of the equipment supplied with the ve-hicle at the time of press. Some of the units described herein will not beavailable until a later date or is only available in certain markets.
The illustrations are intended as a general guide and may vary from theequipment fitted in your vehicle in some details.
The screen colour and the colour of the information displayed on it can varyaccording to vehicle model.
Directions and positions of components (e.g. right, left, front, rear) are al-ways relative to the direction of travel of the vehicle unless otherwise sta-ted.
The equipment marked with an asterisk is only supplied as standard incertain model versions, is optional in others or is only available in spe-cific countries.
Registered trademarks are marked ®. The absence of this symbol doesnot constitute a waiver of the rights concerning any proprietary name.
The section is continued on the following page.
Marks the end of a section.
®WARNINGTexts preceded by this symbol contain information on safety. They warnyou about possible dangers of accident or injury.
CAUTION
Texts with this symbol draw your attention to potential sources of damageto your vehicle.
For the sake of the environment
Texts preceded by this symbol contain relevant information concerning envi-ronmental protection.
Note
Texts preceded by this symbol contain additional information.


7Introduction–FM: switch to FM radio mode. In FM radio mode change the displayof the station buttons ⇒ page 10.
–AM: switch to AM radio mode. In AM radio mode change the displayof the station buttons ⇒ page 10.
–MEDIA: To change to Media mode. In Media mode to select anothermedia source ⇒ page 21.
–MENU: To view the additional functions of the active mode (Radio,Media, etc.). In the additional functions view press the function but-ton SETUP to view the system and function settings ⇒ page 38.
–TP: To switch on or off the traffic news function (Traffic Programme)⇒ page 15.
SOUND: Press to open the sound settings ⇒ page 37.
CD slot: To insert and eject CDs ⇒ page 21.
Screen: The brightness can be adjusted ⇒ page 38.
EJECT: Press to eject the CD ⇒ page 21.
Function buttons: The active function is shown with the correspondingbutton in the display and is activated by pressing ⇒ page 8.
Setting knob: the function of this button depends on the unit's operat-ing state.
–Turn in all Radio modes to tune the stations or channels manuallyand press to start and stop the scan function (SCAN) ⇒ page 10.
–Media mode: Turn to change track manually and press to start andstop the scan function (SCAN) ⇒ page 21.
–In a settings menu turn to change a setting ⇒ page 37.
345678 ...  Rocker switch: The labelling and function depends on the partic-ular version of the unit.
– ENS / ... : Press briefly to the right or left in DAB Radio mode tochange to the next or previous set of DAB stations ⇒ page 18.
– FOLDER  or ... / FLDR : Press briefly to the right or left in Mediamode to change the folder or playlist ⇒ page 21.
 SEEK / TRACK  Rocker switch:
–Press briefly to the right or left to change station in all Radio modes⇒ page 10.
–Press briefly to the right or left in Media mode to change track (title)and hold to fast forward and rewind ⇒ page 21.
910

8IntroductionGeneral information on operating the unit
Introduction
Depending on the vehicle you can also change the track or station and ad-just the volume using the multifunction steering wheel ⇒ Booklet Instruc-tion manual, chapter Overview of the vehicle.
Additional information and warnings:
●
Safety notes  ⇒ page 4
●
Unit overview ⇒ page 6
Additional display information
Depending on the vehicle specification, changes to air conditioning set-tings or information on factory-fitted driver assistance systems may be dis-played temporarily on the screen. These displays disappear automaticallywhen they are no longer required.
Note
●Only a small amount of pressure is needed to operate the unit.●
Due to country-specific legislation, certain functions cannot be selectedwhen the vehicle is travelling above a certain speed.
●
Using a mobile phone in the vehicle may cause noise from the vehiclespeakers.
●
In some vehicles equipped with a parking distance warning system, thevolume of the current audio source is automatically lowered when reversegear is engaged.

Rotary/push knobs, unit and function buttons
Overview
●
Rotary/push knobs.
●
Labelled unit buttons (hard keys).
●
Function buttons (soft keys).
Rotary/push knobs
The left-hand rotary/push knob ⇒ Fig. 1
1
is referred to as the volume con-trol  or the on/off switch.
The right-hand rotary/push knob ⇒ Fig. 1
8
is referred to as the settingknob.
Unit buttons and function buttons
The system labelled buttons are called “unit buttons”, e.g. SOUND button⇒ Fig. 1.
There are six unlabelled unit buttons below the screen ⇒ Fig. 1
7
. Theseare known as “function buttons” because their function depends on the ac-tive function mode.
The current function of a function button is displayed just above the buttonin the bottom line of the screen (e.g. ⇒ Fig. 6).

Switching on and off
●
To switch the unit on or off manually, briefly press the rotary/push knob ⇒ Fig. 1 rotary/push knob.
When the unit is switched on the system starts up. The last audio sourceused is played at the last selected volume setting, provided this does notexceed the preselected “switch-on volume” (ON-VOL or START-VOL⇒ page 38).

9IntroductionDepending on the unit and country, the unit is switched off when the engineis turned off or the key is removed. If the unit comes on again without theignition being switched on, it will switch off automatically after 30 minutes(switch-off delay).
Energy management
If, when the ignition is switched off and the unit switched on, the batteryvoltage falls below the minimum onboard power supply voltage, an audiblewarning sounds and LOW BATTERY appears. You should switch the unit off.
If the battery voltage level continues to fall, LOW BATTERY and RADIO OFF arebriefly shown on the display. The unit will switch off automatically.

Adjusting the base volume
effectActionIncrease the vol-ume.On the radio: Turn the volume control  ⇒ Fig. 1 1
clockwise.On the multifunction steering wheel: Turn the volumecontrol up or press the corresponding button (depend-ing on equipment fitted) ⇒ Booklet Instruction Manual,chapter Overview of vehicle
Decreasing thevolumeOn the radio: Turn the volume control  ⇒ Fig. 1 1 an-ticlockwise.On the multifunction steering wheel: Turn the volumecontrol down or press the corresponding button (de-pending on equipment fitted) ⇒ Booklet InstructionManual, chapter Overview of vehicle
Changes to the volume are indicated by a bar on the screen.
At “0” the unit is muted (display: ) and any media source currently beingplayed will be stopped.
It is possible to preset certain volume settings and adjustments⇒ page 38.
Note
If the basic playback volume of an audio source has been increased sub-stantially, lower the volume before changing to another audio source.


10Audio modeAudio modeFM and AM Radio mode
Introduction
The radio system is supplied in different versions depending on the countryand model in which it is installed and the vehicle equipment. The overviewof the unit shows all the possible versions ⇒ Fig. 1.
How the Radio mode is activated and operated depends partly on the ver-sion of the unit.
Additional information and warnings:
●
Safety notes  ⇒ page 4
●
Unit overview ⇒ page 6
●
RDS and TP radio data services (Traffic Programme) ⇒ page 15
●
System and function settings (SETUP) ⇒ page 38
Note
●Multi-storey car parks, tunnels, high buildings and mountains can im-pair radio signals.●
Foil or metal-coated stickers attached to the windows may affect recep-tion on vehicles with a window aerial.

RADIO main menuFig. 2
RADIO main menu
●
Depending on the version of the unit press the RADIO or BAND⇒ Fig. 1
2
button to start Radio mode.
●
OR: For units with FM and AM buttons, press one of them to activateRadio mode in one of the frequency bands.
The station you are currently listening to is shown in the middle of thescreen ⇒ Fig. 2.
If the RDS function is available it may show the name of the station insteadof the frequency ⇒ page 15.
After you switch to Radio mode, the available frequency bands are initiallydisplayed in the bottom line of the screen ⇒ Fig. 3. After roughly 5 seconds,they are replaced by the “station buttons” ⇒ Fig. 2 - - -. Stations can bestored to the station buttons ⇒ page 13.


11Audio modeChanging frequency bandFig. 3
RADIO main menu: The frequency bands are displayed with memory levels.
The selected frequency band is shown above the station.
After you switch to Radio mode, the available frequency bands and memorylevels are displayed for roughly 5 seconds in the bottom line of the screen⇒ Fig. 3. Then, in their place, the “station buttons” for the selected memorylevel will be shown ⇒ page 13.
●
In Radio mode, briefly press the RADIO or BAND ⇒ Fig. 1
2
unit buttonand it will show the frequency bands and memory levels available.
●
Press one of the function buttons shown ⇒ Fig. 3 to change to the fre-quency band in question.
●
ALTERNATIVELY: Press the RADIO or BAND unit button to move throughthe frequency bands and the levels of memory displayed.
For units with the buttons FM and AM, a frequency band is activated bypressing the corresponding unit button directly.

Changing stationsFig. 4
Change stations using the rocker switch and the setting: "SK MODE: ALL STA-TIONS".
Fig. 5
Change stations using the rocker switch and the setting: "SK MODE: PRESET"(it is only possible to change to stations recorded in the memory).
●
Briefly press the  SEEK / ...  ⇒ Fig. 1 rocker switch to the left or right.
According to the system SEEK MODE settings, stations in the whole frequen-cy bandwidth or only those memorised will be searched ⇒ page 38.

12Audio modeStatuseffectRadio mode with ... displayed inthe centre line of the screen⇒ Fig. 4.
Switches to the next available stationon the current frequency band. As youscroll through the subsequent sta-tions will be shown.
Radio mode with ... displayed inthe bottom line of the screen⇒ Fig. 5.
Switches to the next stored station⇒ page 13.Radio mode with ... displayed inthe centre line of the screen and TPindication ⇒ Fig. 4.
Switches to the next available trafficnews station ⇒ page 15.
AM mode: quickly browsing the frequency band
In AM mode it is possible to skip stations.
●
Press and hold the  SEEK / ...  rocker switch.
●
When the rocker switch  SEEK / ... is released  a search will be per-formed until the next tunable station is found.
Tuning to a station frequency manually
●
Select the desired frequency band ⇒ page 10.
●
Turn the setting knob ⇒ Fig. 1
8
until the desired station frequency(e.g. 89.9 MHz) is displayed on the screen.

Scan function (SCAN)Fig. 6
Additional radio functions and scan in progress (SCAN).
Starting and stopping the scan function
●
Select the desired frequency band in Radio mode ⇒ page 10.
●
Press the setting knob ⇒ Fig. 1
8
to start the scan function.
●
OR: Press the MENU unit button ⇒ Fig. 1
2
and start the scan functionwith the SCAN function button. ⇒ Fig. 6
The scan function commences with the following available station. The func-tion button SCAN is underlined.
In general all the stations that can be received on the selected frequencyband are played for approximately 5 seconds.
●
Press the setting knob or the SCAN function button again to stop thescan function at the station that is currently tuned.
Selecting SCAN PRE or SCAN ALL
If when you start the scan function a stored station is played, in some unitsyou can select whether to play only the stored stations or all the stationsthat can be received by pressing several times. The function button displaywill change accordingly:
SCAN PRE: Only the stored stations will be played.

13Audio modeSCAN ALL: All the stations that can be received in the selected frequencyband will be played.
Special case: Search using the  SEEK / ... rocker switch  after completingthe scan function (SCAN)
If all tunable stations have been listened to, and the scan function (SCAN)has stopped, the search for stations using the rocker switch  SEEK / ... will, in this case, search all tunable stations, even if the SEEK MODE functionsetting is PRESET ⇒ page 38.
Note
If traffic news monitoring is switched on (display: TP), the scan function onlytunes to stations that support the TP function ⇒ page 15.

Selecting the memory level
Fig. 7
Select the frequency band and memory level.
For each frequency band available (for example, FM and AM) there are dif-ferent memory levels (in Fig. 7: FM1, FM2 and AM1, AM2).
Each memory level shows six function buttons to store and tune in the radiostations. These function buttons are called “station buttons”.
When you change to Radio mode, the available memory levels are shownfirst ⇒ Fig. 7 and then, after 5 seconds, the station buttons of the memorylevel selected ⇒ Fig. 8.
Changing the memory level in Radio mode
●
Press the unit button to activate Radio mode (RADIO, BAND, FM or AM⇒ Fig. 1
2
) and for it to show the available memory levels for approximate-ly 5 seconds ⇒ Fig. 7.
●
Press the unit button again to change to the next memory level(in Fig. 7: FM2).
●
OR: Activate the memory level pressing the corresponding function but-ton.
After 5 seconds the stations stored in the station buttons are displayed⇒ Fig. 8. Free preset buttons are indicated by - - -.
When you change the memory level you can also change the frequencyband ⇒ page 11.
You can assign stations to the station buttons of a memory level either man-ually or automatically ⇒ page 13.

Storing and tuning in stations
Fig. 8
Stations stored to station buttons in the FM1 memory level.

14Audio modeAssigning individual station buttons manually●
Select the frequency band and memory level.
●
Select the station.
●
Press and hold the chosen station button until you hear a tone.
●
The station that is currently playing (on Fig. 8: 89.9MHz) will be memo-rised on this preset button.
The station button to which the station currently playing is assigned is dis-played underlined on the screen.
Storing stations automatically (AUTOSTORE)
The Autostore function automatically stores the stations with the strongestreception at the current moment to the six station buttons in the currentlyselected memory level.
●
Select the frequency band and memory level.
●
Press the MENU ⇒ Fig. 1
2
unit button to open the additional functions⇒ Fig. 6.
●
Press and hold the AUTOSTORE function button until AUTOSTORE appearsin the centre line of the screen.
●
This procedure can take some seconds. When the stations have beenstored, AUTOSTORE disappears from the display.
Tuning in to stored stations
●
Select the frequency band and memory level in which the desired sta-tion is stored.
●
Briefly press the station button that displays the desired station.
Depending on the setting you can go through the stored stations of a fre-quency band with the rocker switch  SEEK / ...  ⇒ Fig. 1 (SETUP: SEEK MODEPRESET ⇒ page 38).
A stored station can only be played if it can be received at your current loca-tion.
NoteThe stored stations are overwritten if, in the same memory level, anotherstation is stored in a station button that is already in use.


15Audio modeRDS* and TP* radio data services (Traffic
Programme)
Introduction
The RDS (Radio Data System) offers additional information in FM such as thevisualisation of the station name, automatic station tracking (AlternativeFrequencies), text emitted by radio (Radio Text) and traffic reports (TP).
Not all units have RDS, not all the FM stations offer this service and nor canthe infrastructure of all the countries permit it.
Without RDS, it is not possible to obtain radio data services.
To guarantee the best reception in places where RDS is available for the sta-tions tuned in, select the following system settings ⇒ page 38:
●
RDS ON
●
ALTERNATIVE FREQUENCY ON
●
RDS REGIONAL AUTO
Depending on the unit some settings may not be selected.
Additional information and warnings:
●
Safety notes  ⇒ page 4
●
Unit overview ⇒ page 6
●
Radio mode ⇒ page 10
●
System and function settings (SETUP) ⇒ page 38
Note
The radio stations are responsible for the content of the information sent.

Radio data services RDSFig. 9
Display of the station name. TP function active.
With RDS the station name can be displayed instead of the frequency⇒ Fig. 9.
Automatic station tracking
With the automatic station tracking the unit always switches to the frequen-cy that offers the best reception of the current radio station as the vehicletravels from one area to the next. In some units it is possible to suppressautomatic frequency changing (ALTERNATIVE FREQUENCY OFF)⇒ page 38.
Radio text
Some RDS-compatible stations also broadcast additional text informationknown as radio text. It is possible to adjust the display to show radio text⇒ page 38.
