oil temperature SKODA FABIA 2000 1.G / 6Y Workshop Manual

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 7 02
Replace engine oil filter
Vehicles with petrol engine
Special tools, test and measuring equipment and
auxiliary items required
♦Oil filter wrench
–Release oil filter (e.g. Würth, Hazet) and remove.
–Clean sealing surface at engine.
–Oil rubber seal slightly.
–Screw in new filter and tighten by hand.
–After filling with oil, run engine until it is at operating
temperature and inspect for leaks.
Vehicles with diesel engine
Special tools, test and measuring equipment and
auxiliary items required
♦Oil filter wrench -3417- or wrench 36
–Release cap -1-.
–Replace O-rings -2- and -3- as well as oil filter element
-4-.
–Tighten cap -1-.
Tightening torque of the cap: 25 Nm
Replacing timing belt and tensioning
pulley for camshaft drive (1.9 TDI en-
gines)
–Removing and installing the timing belt
⇒Rep. Gr. 13; 1.9/74 TDI Engine, Mechanics, or
⇒Rep. Gr. 13; 1.9/96 TDI Engine, Mechanics.
Replacing timing belt and tensioning
pulley for camshaft drive (1.4 TDI en-
gines)
–Removing and installing the toothed belt
⇒Rep. Gr. 13; 1.4/55 TDI Engine, Mechanics.
Inspecting timing belt for camshaft drive
for wear and running (petrol engine)
Check timing belt for:
♦Tears or splits -A-, cross-sectional fractures
♦Lateral catches -B-
♦Fraying or chunking -C-
♦Crack in the base tooth -D-
♦Separation of layers (timing belt housing, cords)
♦Traces of oil and grease
S02-0339
2
1
4
3

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 8 02
The timing belt must most definitely be replaced if any
shortcomings are found. This will help prevent any fail-
ures or operational problems. Replacing the timing belt is
a repair measure.
Replacing toothed belt and guide pulley
for camshaft drive (1.9 SDI engines)
–Removing and installing the toothed belt
⇒Rep. Gr. 13; 1.9/47 SDI engine, Mechanics.
Inspecting engine oil level
When inspecting, pay attention to the following points:
Before inspecting, warm up the engine to normal temper-
ature.
Wait at least 3 minutes after switching off the engine to al-
low the oil to flow back into the oil pan.
–Withdraw dipstick, wipe off with a clean cloth and re-
insert dipstick fully.
–Withdraw dipstick once again and read off oil level.
Fig. 1: Oil dipstick version I
Fig. 2: Oil dipstick version ll
The oil level in area -a-
–The oil must be topped up. It is sufficient when the oil
level rises to the area -b-.
The oil level in area -b-
–The oil can be topped up. It is possible that the oil level
will rise to the area -c-.
The oil level in area -c-
–The oil must not be topped up.
♦The oil level must not, under any circumstances, be
above area -a- - danger of damage to the catalytic
converter.
♦The vehicle must be standing on level ground when
measuring the oil level. Wait a few minutes after
switching off the engine to allow the oil to flow back
into the oil pan.
Change engine oil
♦The engine oil should always be changed, if possible,
when the engine is at normal operating temperature.
♦If the engine oil is drained, replace the seal of the oil
drain plug.
Note
Note
Note

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
GearboxEdition 07.03
S00.5301.12.2002-4 page 4 02
–Bring ATF to test temperature.
Test temperature: 35 C to 45 C
–Remove screw plug for ATF inspection in the oil pan
-arrow-.
The ATF present in the overflow tube flows out.
If ATF drips out of the hole:
It is not necessary to top up with ATF.
–Fit new gasket ring on screw plug and tighten to 15
Nm.
Topping up ATF
–Lever off cap -arrow- for securing the screw plug with
a screwdriver.
The cap with the clip lock is destroyed in the process,
therefore always replace the cap.
–Pull off screw plug from the filler tube.
–Top up ATF with the ATF filling system -V.A.G 1924 -
until ATF flows out of the inspection hole -arrow-.
Too much or too little ATF filling impairs the gearbox func-
tion.
S37-0079
S37-0080
V.A.G. 1924
S37-0081
Note

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Exhaust-emission AnalysisEdition 09.04
S00.5301.14.2002-8 page 2 02
♦Disconnect and connect wires of the ignition system
(including high-voltage wires) when the ignition is
switched off.
–Connect the tester in compliance with the operating
instructions.
The exhaust gas probe must be fully inserted into the ex-
haust tailpipe (do not insert into the suction tube)!
–Start engine and run in idle.
–Measure idle speed and CO content.
Test Values for Exhaust-Emission Analysis on Models with Fuel Engines
Note
Engine identification
charactersARV and AQV ARV and AQV ARV and AQV AWY
Model year MY00 MY01 MY02 MY02 ➤
Oil temperature min. 80 °Cmin. 80 °C min. 80 °Cmin. 80 °C
Catalyst warming-up time2 min.
at 2500 rpm2 min.
at 2500 rpm2 min.
at 2500 rpm2 min.
at 2500 rpm
Idling speed
(rpm)590 ... 790 590 ... 690 590 ... 790 600 ... 800
CO content at idle speed
(measured after catalyst)0,0 ... 0,5% 0,0 ... 0,5% 0,0 ... 0,5% 0,0 ... 0,5%
Increased idling speed
(rpm)2400 - 2600 2400 - 2600 2400 - 2600 2400 - 2600
Lambda value
at 2850 - 2900 rpm0,97 ... 1,03 0,97 ... 1,03 0,97 ... 1,03 0,97 ... 1,03
CO content
at 2850 - 2900 rpmmax. 0.3% max. 0.3% max. 0.3% max. 0.3%
Speed for control loop
test (rpm)490 ... 890 490 ... 790 490 ... 890 500 ... 900
Lambda probe version - - - Jump probe
Voltage jump (V) - - - 0,3
DELTA-lambda 0,03 0,03 0,03 0,03
Test speed - - - Idling speed

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Exhaust-emission AnalysisEdition 09.04
S00.5301.14.2002-8 page 3 02
Engine identification
charactersAZQAZE, AZF and
AMEAT Z A Q W
Model year MY03 ➤MY00 ➤ MY03 MY00 MY01 ➤ MY03
Oil temperature min. 80 °Cmin. 80 °C min. 80 °Cmin. 80 °C
Catalyst warming-up time2 min.
at 2500 rpm2 min.
at 2500 rpm2 min.
at 2500 rpm2 min.
at 2500 rpm
Idling speed
(rpm)650 ... 850 700 ... 900 700 ... 900 700 ... 900
CO content at idle speed
(measured after catalyst)0,0 ... 0,5% 0,0 ... 0,5% 0,0 ... 0,5% 0,0 ... 0,5%
Increased idling speed
(rpm)2400 - 2600 2400 - 2600 2400 - 2600 2400 - 2600
Lambda value
at 2850 - 2900 rpm0,97 ... 1,03 0,97 ... 1,03 0,97 ... 1,03 0,97 ... 1,03
CO content
at 2850 - 2900 rpmmax. 0.3% max. 0.3% max. 0.3% max. 0.3%
Speed for control loop
test (rpm)550 ... 950 600 ... 1000 600 ... 1000 600 ... 1000
Lambda probe version - - - -
Voltage jump (V) - - - -
DELTA-lambda 0,03 0,03 0,03 0,03
Test speed - - - -
Engine identification
charactersAUAAUA
with manual gear-
boxAUA
with automatic
gearboxBBY
with manual
gearbox
Model year MY00 and MY01 MY02 MY02 MY02 ➤
Oil temperature min. 80 °C min. 80 °C min. 80 °Cmin. 80 °C
Catalyst warming-up time2 min.
at 2500 rpm2 min.
at 2500 rpm2 min.
at 2500 rpm2 min.
at 2500 rpm
Idling speed
(rpm)650 ... 850 650 ... 850 580 ... 780 660 ... 860
CO content at idle speed
(measured after catalyst)0,0 ... 0,5% 0,0 ... 0,5% 0,0 ... 0,5% 0,0 ... 0,5%
Increased idling speed
(rpm)2400 - 2600 2400 - 2600 2400 - 2600 2400 - 2600
Lambda value
at 2850 - 2900 rpm0,97 ... 1,03 0,97 ... 1,03 0,97 ... 1,03 0,97 ... 1,03
CO content
at 2850 - 2900 rpmmax. 0.3% max. 0.3% max. 0.3% max. 0.3%
Speed for control loop
test (rpm)
550 ... 950 550 ... 950 480 ... 880 560 ... 960
Lambda probe versionWide band probe
(lambda)Wide band probe
(lambda)Wide band probe
(lambda)Wide band probe
(lambda)
Voltage jump (V) - - - -
DELTA-lambda 0,03 0,03 0,03 0,03
Test speed Idling speed Idling speed Idling speed Idling speed

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Exhaust-emission AnalysisEdition 09.04
S00.5301.14.2002-8 page 4 02
Engine identification
charactersBBY
with automatic
gearboxAUB BBZ AZL
Model year MY02 ➤MY00 ➤ MY02 MY02 ➤MY01 ➤
Oil temperature min. 80 °C min. 80 °C min. 80 °Cmin. 80 °C
Catalyst warming-up time2 min.
at 2500 rpm2 min.
at 2500 rpm2 min.
at 2500 rpm2 min.
at 2500 rpm
Idling speed
(rpm)580 ... 780 740 ... 940 580 ... 780 680 ... 880
CO content at idle speed
(measured after catalyst)0,0 ... 0,5% 0,0 ... 0,5% 0,0 ... 0,5% 0,0 ... 0,5%
Increased idling speed
(rpm)2400 - 2600 2400 - 2600 2400 - 2600 2400 - 2600
Lambda value
at 2850 - 2900 rpm0,97 ... 1,03 0,97 ... 1,03 0,97 ... 1,03 0,97 ... 1,03
CO content
at 2850 - 2900 rpmmax. 0.3% max. 0.3% max. 0.3% max. 0.3%
Speed for control loop
test (rpm)480 ... 880 640 ... 1040 480 ... 880 580 ... 980
Lambda probe versionWide band probe
(lambda)Wide band probe
(lambda)Wide band probe
(lambda)-
Voltage jump (V) - - - -
DELTA-lambda 0,03 0,03 0,03 0,03
Test speed Idling speed Idling speed Idling speed -
Engine identification
charactersBMD BKY
Model year MY04 ➤MY04 ➤
Oil temperature min. 80 °C min. 80 °C
Catalyst warming-up time2 min.
at 2500 rpm2 min.
at 2500 rpm
Idling speed
(rpm)620 ... 820 660 ... 860
CO content at idle speed
(measured after catalyst)0,0 ... 0,5% 0,0 ... 0,5%
Increased idling speed
(rpm)2400 - 2600 2400 - 2600
Lambda value
at 2850 - 2900 rpm0,97 ... 1,03 0,97 ... 1,03
CO content
at 2850 - 2900 rpmmax. 0.3% max. 0.3%
Speed for control loop
test (rpm)520 ... 920 560 ... 960
Lambda probe version Jump probeWide band probe
(lambda)
Voltage jump (V) - -
DELTA-lambda 0,03 0,03
Test speed - -

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Exhaust-emission AnalysisEdition 09.04
S00.5301.14.2002-8 page 5 02
All tubes and plug connections, which had been removed
or disconnected for the test and adjustment, must be re-
inserted or connected.
Technical data of the spark plugs Chapter 02-3.
Exhaust-Emission Analysis on Models
with Diesel Engines
♦When possible the test should be carried out immedi-
ately after the road test and also outdoors. If specific
reasons prevent this (weather conditions, excessive
noise in residential areas) the test may also be per-
formed in the workshop.
♦Secure the engine bonnet in the first stop while meas-
uring to reduce the noise.
Visual inspection
♦Hose for crankcase ventilation is connected
♦Fuel system and injection pump must be tight
♦The exhaust system must be undamaged and tight
♦All vacuum hoses are connected
Test and setting conditions
•Engine oil temperature at least 80 °C
•All electrical components disconnected
•No fault stored in the fault memory ⇒Chapter 02-6,
connect vehicle system tester and interrogate fault
memory
Correct detected faults before measuring (repair meas-
ure).
Connect the test equipment
–Connect the tester in compliance with the operating
instructions.
–Start engine, warm up to normal temperature and run
in idle.
–Perform the exhaust-emission analysis.
♦Activate and inspect auxiliary equipment such as e.g.
power steering, automatic gearbox or air conditioning
system. Check whether the engine continues to run
perfectly under this load.
♦All tubes and plug connections, which had been re-
moved or disconnected for the test and adjustment,
must be re-inserted or connected.
Note
Note
Note
Note

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Exhaust-emission AnalysisEdition 09.04
S00.5301.14.2002-8 page 6 02
Test Values for Exhaust-Emission Analysis on Diesel Engines
If the actual values differ from the nominal values: Repair
and again perform an exhaust-emission analysis.Engine identification
charactersAMF ASY ASY ASZ
Model year MY03 ➤MY00 ➤ MY02 MY03 ➤MY03 ➤
Oil temperature
1)
1)From an engine oil temperature of min. 60°C warm up the engine to min. 80°C with 10 free accelerations up to cutoff speed.
min. 80 °Cmin. 80 °Cmin. 80 °Cmin. 80 °C
Idling speed
(rpm)850 … 1050 825 … 950 825 … 950 800 … 1000
Cutoff speed
(rpm)4700 … 4900 4750 … 4950 4650 … 5050 4900… 5300
Soot emission max.
opacity value
2)
2)After the process - free acceleration.
0.9 m-10.8 m-10.8 m-10.98 m-1
Probe no. 1 1 1 1
Measurement mode B B B B
Measurement time slice 0.5 s 0.5 s 0.5 s 0.5 s
Engine identification
charactersAT D AT D
Model year MY00 ➤ MY02 MY03 ➤
Oil temperature
1)
1)From an engine oil temperature of min. 60°C warm up the engine to min. 80°C with 10 free accelerations up to cutoff speed.
min. 80 °Cmin. 80 °C
Idling speed
(rpm)800 … 1000 800 … 1000
Cutoff speed
(rpm)4600 … 5000 4600 … 5000
Soot emission max.
opacity value
2)
2)After the process - free acceleration.
1.5 m-10.6 m-1
Probe no. 1 1
Measurement mode B B
Measurement time slice 0.5 s 0.5 s