boot SKODA FABIA 2010 2.G / 5J User Guide

Seats and Storage
63
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Installing– Press the wire clamps in the direction
of the arrow and place it in its holder.
– Fold the seat cushion back into its original position.PedalsConcerning a secure depressing of the peda
l, you should use only footmats from the
Škoda genuine accessories. Operation of the pedals must not be hindered!
WARNING

Greater pedal distances may be needed when there is a fault in the brake
system.
Do not place any footmats or other additional floor coverings in the area of
the pedals in order to ensure that all the pedals can be fully depressed and are able to return unobstructed to their initial position - risk of accident!
There must be no objects on the floor
which could roll under the pedals. You
would then no longer be able to apply
the brakes, operate the clutch or acceler-
ator - risk of accident!luggage compartmentLoading the luggage compartmentPlease observe the following in the interest of having good handling characteristics of your vehicle: – Distribute the items of luggage as evenly as possible.– Place heavy objects as far forward as possible.– Attach the items of luggage to the
lashing eyes or the fixing net*
page 64.
In the event of an accident, there is such a
high kinetic energy wh
ich is produced by
small and light objects that th
ey can cause severe injuries. The magnitude of the kinetic
energy depends on the speed at which the vehicle is travelling and on the weight of the object. The speed at which the vehicle is trave
lling is in this case the more significant
factor. Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured object with a weight of 4.5 kg produces an en
ergy, which corresponds to 20 times its own
weight. This means that it results in a weight of approx. 90 kg. You can imagine the inju- ries that can occur, if this “bullet” is flyi
ng through the interior compartment and hits
an occupant.
WARNING

Stow the objects in the luggage compartment and attach them to the
lashing eyes.
Loose objects in the passenger compartment can be thrown forward during
a sudden manoeuvre or in case of an accident and can injure the occupants or other oncoming traffic. This risk is still increased, if the objects which are flying around are hit by a deployed airbag. In this case, the objects which are thrown back can injure the occupants - hazard.
Please note that the handling properties of your vehicle may be affected
when transporting heavy objects as a result
of the displacement of the centre of
gravity. The speed and style of driv
ing must be adjusted accordingly.

The items carried in the luggage compartment should be stowed in such a
way that no objects are able to slip fo
rward if there are any sudden driving or
braking manoeuvres underta
ken - risk of injury!

When transporting fastened objects
which are sharp and dangerous in the
luggage compartment enlarged by folding the rear seats forward or removing the rear seats, ensure the safety of th
e passengers transported on the other rear
seats
page 115, “Correct seated position for the occupants on the rear seats”.

If the rear seats next to the folded
forward seat are occupied, ensure
maximum safety, e.g. by placing the goods to be transported in such a way that a folding back of the seat is prevented in case of a rear collision.
Never drive with the boot lid fully open
ed or slightly ajar otherwise exhaust
gases may get into the interior of the vehicle - risk of poisoning!
On no account exceed the permissible
axle loads and the permissible gross
weight of the vehicle - risk of accident!
s3j8.a.book Page 63 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
65
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Caution
Do not place any objects with sharp edges in the nets - risk of net damage.Folding hooks*Folding hooks for attaching small items of lu
ggage, such as bags etc., are provided on
both sides of the luggage compartment
fig. 58
.
An item of luggage weighing up to
10 kg can be attached to the hook.
WARNING
Please refer to the following guidelines
page 63.
Luggage compartment cover You can use the luggage compartment cover behind the head restraints for storing
light and soft items.
Fig. 59 Remove / install the luggage compartment coverThe luggage compartment cover can be remo
ved as required if one must transport
bulky goods. – Unhook the support straps
fig. 59
.
– Remove the luggage compartment cover from the holders with adequate
blows to the bottom side of the cove
r in the area between the holders.
– To re-install, place the cover on the cont
act surfaces of the side trim panel and
position the mounts on the cover above
the holders at the side trim panel.
– Interlock the cover with adequate blows to
the top side of the cover in the area
between the holders.
– Attach the support straps on the boot lid. The luggage compartment cover is foreseen for
storage of small objects of up to 2.5 kg.
in weight.
WARNING
No objects should be placed on the
luggage compartment cover, the vehicle
occupants could be endangered if th
ere is sudden braking or the vehicle
collides with something.
Fig. 58 Luggage compartment: folding hook (Fabia)
A1
A2
A3
A2
A1
s3j8.a.book Page 65 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
66
Caution
When closing the boot lid, jamming and da
mage to the luggage compartment cover or
the side trim panel can occur
if handled in an unprofessional way. Therefore, check the
following before closing:
The mounts of the cover must be interlocked on the holders of the side trim
panel .
The items which are transported must not exceed the level of the luggage compart-
ment cover.
The cover must not be jammed in the seal of
the boot lid when it is in the opened
position.
There must be no object in the gap between the opened cover and the rear seat
backrest.
Please ensure that the heating elements
of the rear window heater are not
damaged as a result of objects placed in this area.
Note
When opening the boot lid, lift the luggage compartment cover - risk that objects placed in this area can slip forward!Further positions of the luggage compartment cover You can use the luggage compartment cover behind the head restraints for storing light and soft items.Fig. 60 Luggage compartment cover in the lowe
r position / stowed behind the rear seats
The luggage compartment cover can also be
put into the lower position on the
supporting elements
fig. 60
- left.
The luggage compartment cover can also
be stowed behind the rear seats
fig. 60
-
right.Foldable luggage compartment cover (Combi)Fig. 61 Luggage compartment: Foldable luggage
compartment cover / removing the foldable
luggage compartment coverPulling out– Pull the foldable luggage compartment cover in direction of arrow as far as the
stop into the secured position
fig. 61
.
Folding– Press the cover in the handle area in di
rection of arrow , the cover rolls up auto-
matically.
Removing– Have the foldable luggage compartment cover removed to transport bulky goods
by pressing on the side of
the cross rod in direction of arrow and taking it out
by moving it in direction of arrow
fig. 61
.
A3
A2
A1
A2
A3
A4
s3j8.a.book Page 66 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
70– Fold the surfaces of the seats and seat backrests of the rear seats forward. First the
right then the left backrest.
– Push the net partition housing
page 69, fig. 67
in the direction of arrow
and take it out of the mounts of the rear se
at backrests on the right in the direction
of the arrow .
Installing– Position the net partition housing into the mounts of the rear seat backrests. – Push the luggage net partition housing in
the opposite direction of arrow as far
as the stop.
– Fold the rear seats back into their original position.Bicycle holder in the luggage compartment*Install cross member– Remove the luggage compartment cover
page 66; if necessary we recommend
to remove, the net partition*
page 69.
– Take the head restraints out of the rear
seat backrests and fold the rear seats in
order to extend the luggage compartment as desired.
– Release the fixtures at the ends of
the cross member by fully loosening and
slightly pulling up
the securing screws . The fixtures open when they are not
already opened.
– Position the cross member with the fixed
(not pulled out) part onto the right (in
direction of travel) lashing eye and then the pull out part onto the left lashing eye.
– Press the fixtures on both sides of the cross member until they lock in place and
tighten the securing screws .
– Check the attachment of the cross member by pulling it.
WARNING
When transporting the bicycles in the
luggage compartment, ensure the safety
of the passengers transported.Install bicycle carrier– Position the approved bicycle carrier on
the middle of the cross member, after
pulling up the screw push the frame side rail (alu-part) towards the cross member and screw the screw into the nut
fig. 69
.
– Slacken the screw and take it out of the moveable part of the fixture; position
the moveable part of the carr
ier, depending on bicycle size
, into one of the possible
positions, so that it does not come in contact with the boot lid. We recommend to place the moveable part of the fixture in such a position that the holes are visible between the screw and the moveable part.
– Insert the screw into the desired position and tighten.
AA
A1
A2
A1
Fig. 68 Install cross member
AB
AC
AA
AB
AC
Fig. 69 Install bicycle carrier
AA
AA
ABAA
AB
s3j8.a.book Page 70 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
71
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Put bicycle into the bicycle carrierFig. 70 Put in the bicycle / fastening the front wheel– Remove the front wheel before putti
ng the bicycle into the vehicle.
– Slacken the quick tension jack on the fixi
ng axle of the bicycl
e carrier and adjust
according to the width
of the bicycle fork.
– Fit the bicycle fork onto
the fixing axle and tighten with the quick tension jack
 fig. 70
.
– Position the left pedal of the bicycle forward, in order to attach the front wheel
more easily.
– Slacken the screw
page 70, fig. 69
and push the bicycle
holder together with
the attached bicycle to the le
ft (in the direction of the arrow), so that no collision
between the steering arm and the side wi
ndow of the luggage compartment can
occur.
– Carefully guide the boot lid to the bottom
without letting it go and at the same time
check if there is adequate room between
the steering arm of the bicycle and the
window of the boot lid. If necessary adapt
the position of the moveable part of the
bicycle carrier in such a way that no collision can occur
page 70.
– It is best to push the removed front wheel between the crank of the left pedal and
the bicycle frame, attach it wi
th a strap to the front fork
fig. 70
, and/or to a fixing
point.
– Make sure that it does not lead to da
mage of the trim panel of the luggage
compartment, the bicycle and the placed objects.
– Perform the installation of the second
fixture and the attachment of the bicycle
analogously.
WARNING
Place the bicycles in the bicycle carrier in such a position that no collision between the steering arm and the side
and/or rear window can occur.
Note
If the front wheel is equipped with disc brake, attach the wheel in such a way that the brake disc is opposite the frame.Secure the stability of the bicycles with a strapFig. 71 Securing the bicycles with clamps / securing the bicycles with a strap– To slacken the rubber part of the clamp,
push both parts against each other and
open the clamp.
– Position the clamp with the rubber part to the front (in direction of travel) as far as
possible below the saddle
rod and close the clamp
fig. 71
.
– When transporting two bi
cycles tension the strap
fig. 71
between the saddle
rods, by pushing the bicycles apart.
– Hang the carabines at the ends of the strap into the lashing eyes behind the rear
seats.
– Pull the strap through the tensioning clasp,
first of all on the one side and then on
the other side.
AA
s3j8.a.book Page 71 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
72– If it is necessary, the position of the bicy
cles in the vehicle can be additionally recti-
fied.
WARNING

When transporting passengers and objects, which require the seats to be
folded forwards, ensure the safety of the passengers being transported.
Place the bicycles in the bicycle carrier in such a position that no collision
between the steering arm and
the rear window can occur.
The roof rack*DescriptionPay attention to the following points if you wish to transport luggage or other items on the roof of your vehicle:
A special roof luggage rack system was de
veloped for the vehicle, that is why you
should only use a roof luggage rack which has been released for use by Škoda Auto.
The base carrier is the basis for a comple
te roof luggage rack system. Separate
additional holders are required for safety reasons for transporting luggage, bikes, surf- boards, skis and boats.
The basic version of the roof luggage rack
system and further components can be
obtained from Škoda original accessories.
Caution

If you use other roof rack systems or if the
roof bars are not properly fitted, then any
damage which may result to your car is no
t covered by the warranty agreements. It is
therefore essential to pay attention to the fitting instructions supplied with the roof luggage rack system.
On models fitted with a power sliding/tilting roof, ensure that the opened
sliding/tilting roof does not strike any items of luggage transported on the roof.
Ensure that the opened boot lid does not collide with the roof load.
For the sake of the environment
The increased aerodynamic drag resu
lts in a higher fuel consumption.
Note
If a roof rail is not fitted onto a vehicle at the works, it is obtainable from a specialist garage which carries out the professional fitting.Attachment pointsInstalling– Insert the attachment points of the roof rack into the mounts of the body so that
the pins of the attachment points grasp into the holes of the body.Note

Pay attention to the information regarding assembly and disassembly in the
attached instructions.
If you have any questions, plea
se contact a specialist garage.
Roof loadDistribute weight evenly over the roof lu
ggage rack system. The maximum permissible
roof load (including roof rack system) of
75 kg
and the maximum
permissible total
weight of the vehicle should not be exceeded.
Fig. 72 Attachment points for base roof carrier
s3j8.a.book Page 72 Tuesday, April 20, 2010 1:10 PM

Taking care of your vehicle and cleaning the vehicle
158
Do not affix any stickers over the inside of
the rear window to avoid damage to the
heating elements of the rear window heater
.
We recommend using a preserva
tive from Škoda genuine accessories offered by your
Škoda dealer.
Caution

Never remove snow or ice from the glass pa
rts with warm or hot water - risk of
formation of cracks in the glass!
When removing snow or ice from the windows and mirror lenses make sure not to
damage the paintwork of the vehicle.The headlight lensesPlease do not use any aggressi
ve cleaning or chemical so
lvent products for cleaning
the front headlights - risk of
damage to the
plastic lenses.
Please use
soap and clean
warm water.
Caution
Never
wipe the headlights dry and do not use any sharp objects for cleaning the plastic
lenses, this may result in damage to the
protective paintwork and consequently in
formation of cracks on the headlight lenses, e.g through effect of chemical products.Door and window sealsThe rubber seals on the doors, boot lid,
bonnet and windows remain supple and last
longer if you treat them from time to time with a rubber care product (e.g. with a spray with silicone-free oil). You also avoid premature wear of the seals and prevent leakages in this way. It is also easier to open the doors. Rubber seals which are well cared for also do not stick together in cold winter weather.Locking cylinderWe recommend that you use the spray from Škoda original accessories with regreasing and anticorrosive effect for de-icing locking cylinders.
Note
When washing your vehicle, ensure that as
little water as possible gets into the locking
cylinders.WheelsSteel wheels You should also thoroughly wash the wheels
and wheel trims when giving your vehicle
its regular wash. This prevents any brake dust, dirt and road salt from sticking to the wheel hubs. You can remove stubborn brake
abrasion adhering to the wheels with an
industrial cleaner. Touch up
any damage to the paintwork on the wheels before rust is
able to form. Light alloy wheels Regular care of light alloy wh
eels is necessary in order to retain their decorative
appearance over long periods. It is particul
arly important to remove any road salt and
brake abrasion from light alloy wheels every two weeks, otherwise the surface will suffer. Wash thoroughly and then treat the wheels with a protective product for light alloy wheels which does not
contain any acidic componen
ts. You should provide the
wheel hubs with a hard wax layer every thre
e months. You must not use any products
which cause abrasion when treating the wheel hubs. Any damage to the paint layer on the wheel hubs must be touched up immediately. We recommend using a preservative from Šk
oda genuine accessories offered by your
Škoda dealer.
WARNING
One should remember when cleaning th
e wheels that moisture, ice and road
salt may adversely affect braking ef
ficiency - risk of an accident!
Note
Severe layers of dirt on the wheels can also
result in wheel imbalance. This may show
itself in the form of a wheel vibration which
is transmitted to the steering wheel which,
in certain circumstances, can
cause premature wear of the
steering. This means it is
necessary to remove the dirt.
s3j8.a.book Page 158 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
204
– Connect the plug to the socket . – Screw in the screws again and insert the cover. The cover must engage firmly.Licence plate light– Open the boot lid and unscrew the light glass
fig. 174
.
– Take the defective bulb out of the holder and insert a new one.– Insert the glass cover of the light again and
press it down to the stop - ensure that
the sealing rubber is
correctly seated.
– Screw on the light glass slightly.Rear light unitFig. 175 Remove the rear light unit / install the rear light unit
– Open the boot lid.– Hold tight the rear light unit with one hand and unscrew the plastic nut with the
other hand
fig. 175
- left.
– Grip the rear light unit and remove it carefully with loosening movements at an
angle to the rear. Do not pull the gro
mmet with the cables out of the body.
– Replace the defective light bulb
page 204.
– When re-installing, first insert the rear light unit with the screw into the opening
of the body
fig. 175
.
– Carefully press the rear light unit into
the body in such a way that the pins
engage into the supports of the body.
– Hold the rear light unit tight with one hand, screw on the nut with the other hand
and tighten it
fig. 175
.
Caution
When removing and installing the rear ligh
t unit make sure not to damage the paint-
work of the vehicle and the rear light unit.
Note
For slackening and tightening the plastic nut use a coin.Changing light bulbs in the rear light unit
AA
AB
Fig. 174 Remove the licence plate light
AA
AB
Fig. 176 Rear light un
it: Fitting position
of the bulbs
s3j8.a.book Page 204 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
205
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– To replace a light bulb, turn the bulb connector of the light bulb to the left (in the
direction of the arrows on the hous
ing) and take it out of the housing.
– Replace the light bulb, put the bulb connect
or back into the housing and turn it to
the right up to the stop (in the opposite
direction of the arrows on the housing).
Fitting position of the light
bulbs in the rear light unit
page 204, fig. 176
.
- Rear fog light / Reversing light - Turn signal lights - Brake lights - Parking lightsLuggage compartment light– Open the boot lid.– Insert a screwdriver into the slot below the light
fig. 177
. Lever out the light care-
fully.
– Disconnect the plug connector. – Replace the defective light bulb.– Recreate the plug connection.– Position the light first of all on the side
of the plug connection and then press it in
on the other side up to the stop.
A1A2A3A4
Fig. 177 Remove the luggage compart- ment light
s3j8.a.book Page 205 Tuesday, April 20, 2010 1:10 PM

Index235
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Index
AAbroad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
ABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Adjusting seats . . . . . . . . . . . . . . . . . . . . . . . . . . 59, 114
Adjusting the steering wheel . . . . . . . . . . . . . . . . . . . 89
Air conditioning system . . . . . . . . . . . . . . . . . . . . . . . 83
Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Deployment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Front airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Head airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Side airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Alternator
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Antilock brake system . . . . . . . . . . . . . . . . . . . . . . . . 140
Antilock brake system (ABS)
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Anti-theft alarm system . . . . . . . . . . . . . . . . . . . . . . . 42
Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Assistance systems
Start-stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Auto Check Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Auto Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Automatic gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Emergency programme . . . . . . . . . . . . . . . . . . . 102
Kickdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Selector lever-emergency unlocking . . . . . . . 103
Tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Automatic vehicle wash systems . . . . . . . . . . . . . . 155
Automatic wiper/washer system . . . . . . . . . . . . . . . 55
AUX-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Avoiding damage to your vehicle . . . . . . . . . . . . . . 150
BBattery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 172
change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Inspecting the electrolyte level . . . . . . . . . . . . . 175
Operation in winter . . . . . . . . . . . . . . . . . . . . . . . 175
Before setting off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Belt tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Belt tensioners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Bicycle holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 165
Boot lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Brake
Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Brake booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171Brake system
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Button on the driver's door
Central locking system . . . . . . . . . . . . . . . . . . . . . 39
Electrical power windows . . . . . . . . . . . . . . . . . . 44
CCar state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Central locking system . . . . . . . . . . . . . . . . . . . . . . . . . 37
lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
unlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Changing a wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Changing wheels around . . . . . . . . . . . . . . . . . . . . 180
Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . 175
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Check engine oil level . . . . . . . . . . . . . . . . . . . . . . . 167
Child safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Side airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Child safety lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Child safety seat
on the front passenger seat . . . . . . . . . . . . . . . 131
Safety information . . . . . . . . . . . . . . . . . . . . . . . 130
Child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Classification into groups . . . . . . . . . . . . . . . . . 132
ISOFIX system . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
s3j8.a.book Page 235 Tuesday, April 20, 2010 1:10 PM