SKODA OCTAVIA 2005 1.G / (1U) Owner's Guide

Instruments and Indicator/Warning Lights
20
The following readouts of the selected memory will be set to zero by
button :
•average fuel consumption,
•distance driven,
•average speed,
•Driving time.
You can only operate the multi-functional indicator when the ignition is
switched on. After the ignition is switched on, the function displayed is the
one which you last selected before switching off the ignition.
If the outside temperature drops below +4 °C, the outside temperature
indicator with a snow flake symbol appears. The symbol warns the driver
of the possible danger of ice on the road. After the rocker switch is
pressed, the function displays the one which you last selected before
switching off the ignition.
The outside temperature
The outside temperature appears in the display when the ignition is
switched on.
The correct outside temperature will be indicated with a delay of 5
minutes. If the vehicle is stationary (or driven at a very low speed) the
temperature indicated may be slightly higher than the actual outside
temperature because of heat radiated by the engine.
If the outside temperature drops below +4 °C, a snow flake symbol
(warning signal for ice on the road) appears before the temperature indi-
cator ⇒fig. 7 and a warning signal sounds.
WARNING
Do not only rely upon the information given on the outside temper-
ature display that there is no ice on the road. Please note that black
ice may also be present on the road surface even at temperatures
around +4 °C - warning, drive with care!
Current consumption
The current fuel consumption level is shown in the display in litres/100 km.
This information can help you to adapt your style of driving to the fuel
consumption you wish to achieve.
The display appears in litres/hour if the vehicle is stationary or driving at a
low speed.
Average fuel consumption
The average fuel consumption since the memory was last erased is
shown in the display in litres/100 km ⇒page 18. This information can help
AB
AA
Fig. 7 Multi-functional
indicator: the outside
temperature
s24s.book Page 20 Thursday, November 24, 2005 12:27 PM

Instruments and Indicator/Warning Lights21
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
you to adapt your style of driving to the fuel consumption you wish to
achieve.
If you wish to determine the average fuel consumption over a certain
period of time you must first erase the memory at the start of the new
measurement using the button
⇒page 19, fig. 6 . A zero appears in the
display for the first 100 m you drive after erasing the memory.
The indicated value will be updated every 5 seconds while you are driving.
Note
The amount of fuel consumed will not be indicated.
Range
The estimated range in kilometres is shown on the display. It indicates the
distance you can still drive with your vehicle based on the present level of
fuel in the tank for the same style of driving. The readout is shown in steps
of 10 km.
The fuel consumption for the last 50 km is taken as a basis for calculating
the range. If you drive in a more economical manner from this moment on,
the range will be increased accordingly.
You first drive 50 km if the readout is reset (after disconnecting the
battery) before a new readout for the range is displayed.
Distance driven
The distance driven since the memory was last erased appears in the
display ⇒page 18. If you wish to calculate the distance driven from a particular time of day you must first erase the memory at this moment in
time by pressing the button
⇒page 19, fig. 6 .
The maximum distance indicated in both switch positions is 9999 km. The
indicator is set back to null if this period is exceeded.
Average speed
The average speed since the memory was last erased is shown in the
display in km/hour ⇒page 18. If you wish to determine the average speed
over a certain period of time you must first erase the memory at the start
of the new measurement using the button ⇒page 19, fig. 6 .
A zero appears in the display for the first 100 m you drive after erasing the
memory.
The indicated value will be updated every 5 seconds while you are
driving.
Driving time
The driving time which has elapsed since the memory was last erased,
appears in the display ⇒page 18. If you wish to calculate the driving time
from a particular time of day you must first erase the memory at this
moment in time by pressing the button ⇒page 19, fig. 6 .
The maximum distance indicated in both memories is 99 hours and 59
minutes. The indicator is set back to null if this period is exceeded.
AB
AB
AB
AB
s24s.book Page 21 Thursday, November 24, 2005 12:27 PM

Instruments and Indicator/Warning Lights
22
Warning against excessive speeds*Warning against excessive speeds 1)
This function enables you to set a speed limit, e.g. if you drive in town. A
text in the display is intended to draw your attention to the fact that you
have exceeded the set speed limit.
You can set the desired speed limit as follows:
•Select the menu Speed warning --- km/h (warning at --- km/h) .
•You can drive at the desired speed, e.g. 50 km/h
•Press the button ⇒fig. 9 - Speed warning 50 km/h (warning at 50
km/h) is shown on the display.
If you now exceed the set speed limit, Speed 50 km/h exceeded (speed
50 km/h exceeded) will be shown on the display. This display will be
shown until you have reduced the speed to the set speed limit.
A peep sounds as an additional warning signal.
The set speed limit remains stored in the memory, also when the ignition
is switched off and on; it can only be erased by pressing the button for
more than 1 second.
Fig. 8 Speed setting
Fig. 9 Multi-functional
indicator: Controls
1)Valid for vehicles with information display.
AB
AB
s24s.book Page 22 Thursday, November 24, 2005 12:27 PM

Instruments and Indicator/Warning Lights23
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Information display*
Introduction
The information display provides you with information in a convenient way
concerning the current operating state of your vehicle . The information
system also provides you with data (depending on the equipment installed
in the vehicle) relating to the radio, mobile phone, multi-functional indi-
cator, navigation system and automatic gearbox.
Certain functions and operating conditions are always being checked on
the vehicle when the ignition is switched on and also while driving.
Functional faults, if required repair work and other information are indi-
cated by red symbols ⇒page 27 and yellow symbols ⇒page 28.
Lighting up of these symbols is combined with an acoustic warning signal.
Information and texts giving warnings are also shown in the display
⇒ page 30. The display of text is possible in the following languages:
Czech, English, German, French, Italian, Spanish, Portuguese.
You can select the desired language in the setting menu ⇒page 28.
The following information can be shown in the display (depending on the
equipment installed on the vehicle):
Fig. 10 Instrument
cluster: Information
display
Main menu⇒ page 24
Door, luggage compartment door and bonnet ajar
warning⇒page 25
Service Interval Display⇒page 16
Selector lever positions of the 6-speed automatic
gearbox⇒page 150
Selector lever positions of the automatic DSG⇒page 157
s24s.book Page 23 Thursday, November 24, 2005 12:27 PM

Instruments and Indicator/Warning Lights
24
Main menu
– You can activate the MAIN MENU by pressing the rocker
switch ⇒fig. 12 for more than 1 second. – You can select the menu through the rocker switch . When
the pushbutton is briefly pressed, the information you have
selected is displayed.
You can select the following information (depending on the equipment
installed on the vehicle):
„MF Display ⇒ page 18
„The outside temperature
„Current consumption
„Average fuel consumption
„Range
„Distance driven
„Average speed
„Driving time
„Warning against excessive speeds
„Audio ⇒ page 25
„Navigation ⇒page 26
„Telephone ⇒page 167
„Vehicle status ⇒ page 26
„Setup ⇒ page 28
„Time
„Winter tyres
„Language
„Units
„Lights & Vision
„Aux. Heating (auxiliary heating)
„Back
Fig. 11 Information
display: Menu
Fig. 12 Information
display: Controls
AA
AA
AB
s24s.book Page 24 Thursday, November 24, 2005 12:27 PM

Instruments and Indicator/Warning Lights25
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
„Display off
After selecting the menu Display off the display is switched off. Press
rocker switch for at least 1 second to switch the display on again.
The menu Audio is only displayed when the Radio* is switched on.
The menu Navigation is only displayed when the Navigation* is switched
on.
Aux. Heating (auxiliary heating) is only then displayed, if the vehicle is
fitted with auxiliary heating*.
Note
If you do not activate the information display at that moment, the menu
shifts to one level higher every 10 seconds.
Door, luggage compartment door and bonnet ajar
warning
The door, luggage compartment door and bonnet ajar warning lights up
when at least one of the three items door, luggage compartment or bonnet
are not closed when the ignition is turned on. The symbol indicates which
door is still open or whether the luggage compartment door or bonnet is
not closed ⇒ fig. 13 .
The symbol goes out as soon as the doors, luggage compartment door
and bonnet are completely closed.
As an additional warning signal, a 3 time peep sounds if the car is driven
at a speed of more than 6km/hour and if the door, engine or luggage
compartment door is open.
Audio
These displays appear in addition to the normal information in the radio
display.
AA
Fig. 13 Information
display: Door warning
Fig. 14 Information
display: Radio display
s24s.book Page 25 Thursday, November 24, 2005 12:27 PM

Instruments and Indicator/Warning Lights
26
Operation of the radio system is described in separate operating instruc-
tions to be found in the on-board literature.
Navigation system*
The controls for the navigation system, radio, CD player are located in the
centre console on both sides of the monitor screen. Navigation data is
also shown in the information display of the instrument cluster.
Information and warning texts are displayed preferentially when the navi-
gation system is switched on.
Operation of the navigation system is described in separate operating
instructions to be found in the on-board literature.
Auto Check Control
Vehicle condition
The Auto Check Control carries out a check of certain functions and
vehicle components. The check is performed constantly when the ignition
is switched on, both when the vehicle is stationary, as well as when
driving.
Operational faults, urgent repairs, service work or other information
appear in the display of the instrument cluster. The displays are shown
with a red or yellow light symbol depending on the priority of the message.
The red symbols indicate danger (priority 1) while the yellow symbols indi-
cate a warning (priortity 2). Information for the driver may also appear in
addition to the symbols ⇒page 30.
There is at least one error message to be read when the term Vehicle
status is flashing in the main menu. After selecting this menu the first of
the error messages is displayed. If there are several error messages, they
Fig. 15 Information
display: Display of
operational fault
s24s.book Page 26 Thursday, November 24, 2005 12:27 PM

Instruments and Indicator/Warning Lights27
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
are shown on the display under the message e.g.
01/03 ⇒ fig. 15 . This
display indicates that the first of a total of three error messages should be
displayed. The respective symbols light up one after the other in an
interval of 5 seconds. Investigate the displayed faults as soon as possible.
As long as the operational faults are not rectified, the symbols are always
indicated again. After the first display, the symbols are indicated without
information for the driver.
If there is no error message, after selecting the menu Vehicle status the
message Status OK is shown on the display.
If a fault occurs, a warning signal will also sound in addition to the symbol
and text in the display:
•Priority 1 - three warning signals
•Priority 2 - one warning signal
Red symbols
A red symbol signals danger.
Proceed as follows if a red symbol is displayed:
– Stop the vehicle.
– Switch the engine off.
– Investigate the function indicated.
– Obtain professional assistance.
Meaning of the red symbols:
Coolant level too low/coolant tempera-
ture too high⇒ page 35
Engine oil pressure too low⇒page 37
Fig. 16 Information
display: Oil pressure is
low
s24s.book Page 27 Thursday, November 24, 2005 12:27 PM

Instruments and Indicator/Warning Lights
28
Three successive warning signals will sound if a red symbol appears.
If several operational faults of priority 1 exist, the symbols appear one
after the other and are each illiminated for about 5 seconds.
Yellow symbols
A yellow symbol signals a warning.
Check the relevant function as soon as possible.
The meaning of the yellow symbols: One
warning signal will sound if a yellow symbol appears.
If several operational faults of priority 2 exist, the symbols appear one
after the other and are each illiminated for about 5 seconds.
Settings
Fig. 17 Information
display: Fuel level low
Fuel level low⇒ page 36
Check engine oil level,
engine oil sensor faulty⇒page 38
Brake pad worn⇒page 36
Washer fluid level low⇒page 36
Fig. 18 Setting the
clock
s24s.book Page 28 Thursday, November 24, 2005 12:27 PM

Instruments and Indicator/Warning Lights29
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
You can change certain settings by means of the information display. The
current setting is shown on the information display in the respective menu
at the top below the line
⇒page 28, fig. 18 .
You can select the following information (depending on the equipment
installed on the vehicle):
•Time
•Winter tyres
•Language
•Units
•Lights & Vision
•Aux. Heating (auxiliary heating)
•Back
After selecting the menu Back you will reach one level higher in the menu.
Setting clock
Here you can set the time, the time format (12 or 24 hour indicator) and
the time change summer/winter time.
Setting for winter tyre speed
Here you can set at which speed a warning signal should sound. These
functions are used for e.g on winter tyres with the permissible maximum
speed less than the maximum speed of the vehicle ⇒page 266.
When exceeding the speed, the following is displayed on the information
display*: Speed warning
Language setting
Here you can set in which language the warning and information texts
should be displayed. After selecting the language, e.g. English, the
following is displayed on the information display: Language: english set Setting units
Here you can set the units for temperature, consumption and distance
driven.
Setting lights
Here you can switch on or off the function convenience turn signal
⇒
page 68. Furthermore you can set how long the light should stay on for
the function Coming/Leaving Home ⇒page 66.
After selecting the menu Factory setting the factory setting is established
again.
s24s.book Page 29 Thursday, November 24, 2005 12:27 PM