SKODA OCTAVIA 2009 2.G / (1Z) Manual PDF

Lights and Visibility
70
Switching windscreen wipers off – Move the lever back into its home position .After the windscreen wiper switches off each
time or the igniti
on switches off for
the third time, the position of the windscreen wiper changes, this counteracts an early fatigue of the wiper rubbers. The windscreen wipers and the wash system only operate if the ignition is switched on and the bonnet is closed
11).
If the intermittent wipe is switched on, the intervals are also controlled depending on speed. The rain sensor* automatically regulates
the break between the individual wiper
strokes depending on the intensity of the rain. The rear window will be
wiped again if the front wi
ndow wipers are on when
reverse gear is selected. The windscreen washer nozzles are heated* when the ignition is switched on.Top up with wash liquid
⇒page 236.
Winter position If the windscreen wipers are in rest posi
tion, they cannot be folded out from the
windscreen. For this reason we recommend
adjusting the windscreen wipers in
winter so that they can be folded out fr
om the windscreen easi
ly. You can set this
rest position as follows:•
Switch on the windscreen wipers.
•
Switch off the ignition. The windscreen wi
pers remain in the position in which
they were when switching off the ignition. You can also use the service position
⇒page 71 as a winter position.
WARNING
•
Properly maintained windscreen wiper
blades are essential for clear visi-
bility and safe driving
⇒page 71.
•
Do not use the windscreen
washer system at lo
w temperatures, without
heating the windscreen beforehand.
Otherwise the window cleaner could
freeze on the windscreen and re
strict the view to the front.
•
The rain sensor only operates as a support. The driver is not released
from the responsibility to set the function of the windscreen wipers manu- ally depending on the visibility conditions.
Caution
In frosty weather, please first of all check whether the windscreen wiper blades are not frozen to the windscreen before switching them on. Switching on windscreen wipers when the blades are frozen to the windscreen may result in damage both to the blades and the motor of the windscreen wipers!
Note
•
If the slower or the faster wiper setting is switched on
⇒page 69, fig. 68

and the vehicle speed decreases to below 4
km/h, the lower wiper step is switched
on automatically. At a speed increase of
more than 8 km/h the previous wiper
setting is established again.•
If there is an obstacle on the windscreen, the wiper will try to push away the
obstacle. If the obstacle continues to bloc
k the wiper, the wiper stops after 5 cycles,
in order to avoid a damage to the wiper.
Remove the obstacle and and switch on
the wiper again.Headlight cleaning system*The headlights are being cleaned after the
windscreen has been sprayed for the first
time and fifth time, the low beam or ma
in beam are switched on and the wind-
screen wiper lever was held in the position
⇒page 69, fig. 68
for about 1
second.
11)On vehicles which do not have a contact swit
ch for the bonnet, the windshield wiper and
wash system operates also when the bonnet is opened.
A0
A2
A3
A5
se0.1.book Page 70 Friday, April 10, 2009 3:19 PM

Lights and Visibility
71
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The headlight washer nozzles are moved forward out of the bumper by the water pressure for cleaning the headlights. You should remove stubborn dirt (such
as insect residues) from the headlight
lenses at regular intervals, for example when refuelling. Please refer to the following guidelines
⇒page 214, “The headlight lenses”.
You should remove any snow from the fixt
ures of the washer nozzles and clear ice
in winter with a de-icing spray in order to
ensure proper operation of the cleaning
system.Replacing wiper blades fo
r the windscreen wipers
One cannot fold out the wiper arms in the rest position from the wind- screen. Before replacing the wiper
arms you must put them into the
service position. Service position for changing wiper blades – Close the bonnet. – Switch the ignition on and then again off. – Then press the windscreen wiper lever in the position
⇒
page 69,
fig. 68
within 20 seconds - the wiper ar
ms move into the service posi-
tion.
Taking off the wiper blade – Fold windscreen wiper arm out from
the windscreen and position the
wiper blade at right angles to the wiper arm
⇒
.
– Take off the wiper blade in direction of arrow
⇒
fig. 69
⇒
.
Attaching a wiper blade – Push the new wiper blade over the wiper arm and turn the wiper blade
into the vertical position.
– Check whether the wiper blade is correctly attached.– Fold the windscreen wiper arms onto the window and switch on the
ignition. By pressing the window wi
per lever into the sprung position
⇒
fig. 69
or when driving at a speed greater than 4 km/h, the wind-
screen wiper arms move back into the rest position.
Wiper blades in proper condition are esse
ntial to obtain good visibility. Wiper
blades should not be allowed to become
dirtied by dust, insect remains and
preserving wax. Juddering or smearing of the wiper blades
could then be due to wax residues left
on the windscreen by vehicle washing in
automatic vehicle wash systems. It is
therefore important to
degrease
the lips of the wiper blades after every pass
through an
automatic vehicle wash system
.
WARNING
•
The ignition must not be switched on if the front windscreen wiper arms
are folded out. The wiper blades would move back into their rest position and while doing so damage th
e paintwork of the bonnet.
•
If the windscreen wipers are handled carelessly, there is a risk of damage
to the windscreen.•
You should clean the wiper blades regularly with a windscreen cleaner in
order to avoid any smears. Clean a wiper blade with a sponge or cloth if it is very dirty, for example from insect residues.
Fig. 69 Wiper blade for the windscreen wiper
A4
A4
se0.1.book Page 71 Friday, April 10, 2009 3:19 PM

Lights and Visibility
72
•
Replace the wiper blades once or twice a year for safety reasons. These
can be bought from an authorised Škoda Service Partner.Replacing the wiper blade on
the rear window wiper
Taking off the wiper blade – Fold windscreen wiper arm out from the windscreen and position the
wiper blade at right angles to the wiper arm
⇒
fig. 70
.
– Hold the window wiper arm at the top end with one hand. – With the other hand unlock the locking button in the direction of
arrow and remove the wiper blade.
Attaching a wiper blade – Position the wiper blade onto the wiper arm and lock the locking
button .
– Check whether the wiper bl
ade is correctly attached.
The same remarks apply here as for
⇒page 71.
Rear-view mirrorManual dimming interior rear-view mirrorBasic setting – Pull the lever on the bottom edge of the mirror forward. Dimming mirror – Pull the lever on the bottom edge of the mirror back.Automatic dimming interior mirror*Switching on the automatic dimming– Press the button - the warning light lights up
⇒
fig. 71
.
Switching off the automatic dimming – Press again the button - the warning light goes out .If the automatic dimming is switched on, the mirror dims
automatically

depending on the light striking the mirror from the rear. The mirror has no lever on the bottom edge of the mirror. When the
interior lights are switched on or the
reverse gear is engaged, the mirror alwa
ys moves back into the basic position.
WARNING (continued)
Fig. 70 Wiper blade for rear windowAA
AA
Fig. 71 Automatic dimming interior mirror
AB
AA
AB
AA
se0.1.book Page 72 Friday, April 10, 2009 3:19 PM

Lights and Visibility
73
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Note
•
Automatic mirror dimming operates only pr
operly if the sun screen* for the rear
window in the housing on the luggage comp
artment cover is not in use or the light
striking the interior rear-view mirror is not affected by other objects.•
Do not affix any stickers in front of the light sensor, so that you do not impair the
automatic dimming function or put it out of operation.•
If you switch off the automatic dimming interior rear-view mirror, also the exte-
rior mirror dimming is switched off.Exterior mirror You can adjust the exterior mirrors electrically*.The exterior mirror heater only oper
ates when the engine is running and
up to an outside temperature of +20 °C. Heating of the external mirror – Turn the rotary knob to position
 ⇒
fig. 72
.
Adjusting left and right exterior mirrors simultaneously – Turn the rotary knob to position
. The movement of the mirror surface
is identical to the movement of the rotary knob.
Adjusting the right-hand exterior mirror – Turn the rotary knob to position
. The movement of the mirror
surface is identical to the movement of the rotary knob.
Switching off operating control – Turn the rotary knob to position
.
Folding in both exterior mirrors* – Turn the rotary knob to position

.
Lowerable exterior mirror* with the aid of the key for remote control – If all the windows are closed, press the unlock button on the radio
remote control
⇒
page 50, fig. 47
for approx. 2 seconds.
Tilting surface of front pa
ssenger exterior mirror*
When the rotary knob is in position
 ⇒fig. 72
and the reverse gear is engaged, the
s ur fa ce o f t h e m i rro r t i l ts d o w n s l i g h t l y. T h i s p ro v i d e s a n a i d i n s e e i n g th e ke r b o f t h e pavement when parking the car. The mirror returns into its initial position, after the rotary knob is moved out of the position
 and put into another position or if
the speed is more than 15 km/h.
Memory for exterior mirrors* On vehicles fitted with a memory for the driver seat, the relevant setting of the exte- rior mirror is also stored automatica
lly when the seat position is stored
⇒page 76.
WARNING
•
Convex (curved outward) or spherical (differently curved) exterior
mirrors increase the vision field. Th
ey do, however, make objects appear
smaller in the mirror. These mirrors are
only of limited use, therefore, for
estimating distances to the following vehicles.•
Use whenever possible the interior rear mirror, for estimating the
distances to the following vehicles.
Fig. 72 Inner part of door: Rotary knob
A3
se0.1.book Page 73 Friday, April 10, 2009 3:19 PM

Lights and Visibility
74
Note
•
If the exterior mirrors are folded in using the remote control* of the vehicle key,
these are folded back into the driving position after switching on the ignition.•
If the exterior mirrors are folded in using the rotary knob
⇒page 73, fig. 72
,
they can only be folded back into the
driving position using the rotary knob.
•
If the exterior mirrors were folded in
using the remote control* of the vehicle
key and if the rotary knob was in the fold
-in position before switching on the igni-
tion, the mirrors remain in the fold-in position the next time the ignition is switched on. Folding back into the driving position
is performed by actuating the rotary knob
in a different position fr
om the fold-in position.
•
Do not touch the surfaces of the exterior mirrors if the exterior mirror heater is
switched on.•
You can set the exterior mirr
ors by hand, if the power setting function fails at any
time by pressing on the edge of the mirror surface.•
Contact your specialist garage if a fault exists with the power setting of the exte-
rior mirrors.Automatic dimming exterior mirror*The exterior mirrors are dimmed together with the interior mirror. If the automatic dimming is switched on, the mirror dims
automatically
depending on the light
striking the mirror from the rear. When the interior lights are switched on or
the reverse gear is engaged, the mirror
always moves back into the
basic position (not dimmed).
Note
•
Automatic mirror dimming operates only pr
operly if the sun screen* for the rear
window is not in use or the li
ght striking the rear of the interior rear-view mirror is
not affected by other objects.•
Do not affix any stickers in front of the li
ght sensor, so that you do not impair the
automatic dimming function or put it out of operation.
•
If you switch off the automatic dimming interior rear-view mirror, also the exte-
rior mirror dimming is switched off.
se0.1.book Page 74 Friday, April 10, 2009 3:19 PM

Seats and Stowage
75
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Seats and StowageFront seatsBasic informationThe front seats have a wide range of differ
ent settings and can thus be matched to
the physical characteristics of the driver
and front passenger. Correct adjustment of
the seats is particularly important for:•
safely and quickly reaching the controls,
•
a relaxed, fatigue-free body position,
•
achieving the maximum protection offere
d by the seat belts and the airbag
system.
WARNING
•
Never transport more occupants than the maximum seating in the
vehicle.•
Each occupant must correctly fasten the seat belt belonging to the seat.
Children must be fastened
⇒page 184, “Transporting children safely” with
a suitable restraint system.•
The front seats and the head restraints must always be adjusted to match
the body size of the seat occupant as well as the seat belts must always be correctly fastened in order to provide an optimal protection for you and your occupants.•
Always keep your feet in the footwell
when the vehicle is being driven -
never place your feet on the instrument panel, out of the window or on the surfaces of the seats. This is particularly important for the front seat passenger. You will be exposed to increa
sed risk of injury if it becomes
necessary to apply the brake or in the ev
ent of an accident.
If an airbag is
deployed, you may suffer fatal injuries
when adopting an incorrect seated
position!•
It is important for the driver and front passenger to maintain a distance
of at least 25 cm from the steering wheel or dash panel. Not maintaining this
minimum distance will mean that the airb
ag system will not be able to prop-
erly protect you - hazard! The front seats and the head restraints must always also be correctly adjusted to match the body size of the occupant.•
Ensure that there are no objects in the footwell as any objects may get
behind the pedals during a driving or
braking manoeuvre. You would then
no longer be able to operate the clutch, to brake or accelerate.Adjusting the front seatsAdjusting a seat in a forward/back direction –Pull the lever
⇒
fig. 73
up and push the seat into the desired posi-
tion.
– Release the lever and push the seat further until the lock is heard
to engage.
Adjusting height of seat* – Lift the seat if required by pulling or pumping lever upwards.
WARNING (continued)
Fig. 73 Controls at seat
A1
A1
A2
se0.1.book Page 75 Friday, April 10, 2009 3:19 PM

Seats and Stowage
76
– Lower the seat if required by pushing or pumping lever down-
wards.
Adjust the angle of the seat backrest – Relieve any pressure on the seat backrest (do not lean on it) and turn
the handwheel
⇒
page 75, fig. 73
to adjust the desired angle of the
backrest.
Adjusting lumbar support* – Turn the wheel until you have set the most comfortable curvature
of the seat upholstery in
the area of your spine.
The driver's seat should be adjusted in
such a way that the pedals can be pressed
to the floor with slightly bent legs. The seat backrest on the driver's seat sh
ould be adjusted in such a way that the
upper point of the steering wheel can be easily reached with slightly bent arms.
WARNING
•
Only adjust the driver seat when the ve
hicle is stationary - risk of injury!
•
Take care when adjusting the seat! Adjusting the seat without care can
lead to bruises or injuries.•
The seat backrests must not be angl
ed too far back when driving other-
wise this will affect proper operation of the seat belts and of the airbag system - risk of injury!
Adjusting front seats electrically*Adjusting seatsAdopt the correct seated position before setting
⇒
page 75.
Adjusting a seat in a forward/back direction – Press the switch
⇒
fig. 74
forwards or backwards
⇒
fig. 75
.
Set the height of the seat – Press the switch
⇒
fig. 74
upwards or downwards.
A2
A3A4
Fig. 74 Side view: Controls for adjusting the seatFig. 75 Side view: Seat setting switch
AA
A1
AA
se0.1.book Page 76 Friday, April 10, 2009 3:19 PM

Seats and Stowage
77
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Adjust the angle of the seat – Press the switch at the front
⇒
page 76, fig. 75
or at the back
⇒
page 76, fig. 75
.
Adjusting the seat backrest – Press the switch
⇒
page 76, fig. 74
in the direction of the desired
setting.
Adjusting lumbar support – Press the switch front
⇒
page 76, fig. 74
in order to enlarge the
curvature of the lumbar support.
– Press the switch rear in order to reduce the curvature of the lumbar
support.
– Press the switch top in order to adjust the curvature of the lumbar
support higher.
– Press the switch bottom in order to adjust the curvature of the
lumbar support lower.
Switch is operated in order to move the seat up/down and forward/back, while switch is operated in order to move the seat backrest forward or back.
WARNING
•
Only adjust the driver seat when the ve
hicle is stationary - risk of injury!
•
Caution when adjusting the seat! You ma
y suffer injuries or bruises as a
result of adjusting the seat without paying proper attention.•
In view of the fact that the seats can
also be adjusted when the ignition is
switched off (even when ignition key withdrawn), you should never leave children unattended in the vehicle.•
The seat backrests must not be angled too far back when driving other-
wise this will affect proper operation of the seat belts and of the airbag system - risk of injury!
Note
If the movement of the seat is inadverten
tly interrupted during an adjustment, once
again press the switch in th
e appropriate direction and
continue with the adjust-
ment of the seat to the end.Storing settingStoring seat and exterior mirror settings for driving forward – Switch on the ignition. – Adjust the seat
⇒
page 76.
– Adjust both exterior mirrors
⇒
page 73.
–Press button
SET

⇒
fig. 76
.
– Press one of the memory buttons within 10 seconds after pressing
the button
SET
- an acknowledgement signal confirms that the seat
setting is stored.
Storing exterior mirror setting for reversing* – Switch on the ignition. – Turn the exterior mirror control to position
 ⇒
page 73.
AA
A2
A3
ABACACACAC
AAAB
Fig. 76 Driver seat: Memory buttons and SET button
AA
AB
se0.1.book Page 77 Friday, April 10, 2009 3:19 PM

Seats and Stowage
78
– Engage the reverse gear. – Move the right exterior mirror into the desired position
⇒
page 73.
– Take the vehicle out of gear. The set position of the exterior mirror is
stored.
Memory buttons Memory for the seat offers the possibility to store the individual driver seat and external mirror position. An individual posi
tion can be allocated to each of the three
memory buttons
⇒page 77, fig. 76
, that is three in total. After pressing the
corresponding memory button , the seat
and the exterior mirror are automati-
cally moved into the positions which
have been allocated to this button
⇒page 78.
Emergency Off You can interrupt the setting operation at an
y time, if you operate any button of the
driver seat.
Note
•
When storing settings with the memory buttons, we recommend that you begin
with the front button and assign a memory button to each additional driver.•
Each new setting stored with the same button erases the previous setting.
•
Each time you store the seat and exterior mirror settings for driving forward you
also have to re-store the individual settin
g of the exterior mirror on the passenger
side for reversing.Assigning remote control to the memory buttonsAfter storing the settings of the seat and exterior mirrors, you have 10 seconds in order to assign the radio remote control to the appropriate memory button. – Withdraw the ignition key. – Press the unlock button
⇒
page 50. The setting is stored with the
memory button which you have selected.
If you wish to be able to retrieve the settings which are stored in the memory by also using the radio remote control, you have
to assign the radio remote control to a
memory button in each case. If you wish, you can obtain an additional
remote control key from an authorised
Škoda Service partner and then assign the remote control key to another memory button.
Note
•
If the radio remote control had previous
ly been assigned to another memory
button, this setting is then erased by the new assignment.•
If you assign the radio remote contro
l to a memory button which has already
been assigned to a radio remote control,
the old assignment is also replaced by a
new assignment in this case.•
The assignment of the radio remote control to a memory button is retained,
however, after reassigning the seats and exterior mirrors.Retrieving settings of the seat and mirrors You can retrieve the stored settings
either with the memory buttons
or with the remote control*.Retrieving settings with memory buttons – In order to retrieve the stored
setting, you have two possibilities:
–
One-touch automatic memory:
Briefly press the desired memory
button
⇒
page 77, fig. 76
. The seat and exterior mirror are moved
automatically into the stored positions (this applies only if the ignition is switched on and the speed is less than 5 km/h).
–
Memory keying
: Press and hold the desired memory button
pressed long enough until the seat and the exterior mirror are moved into the stored positions.
AB
AB
AB
AB
se0.1.book Page 78 Friday, April 10, 2009 3:19 PM

Seats and Stowage
79
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Retrieving settings with remote control – If the driver door is closed and the ignition is switched off, briefly press
the unlock button of the radio remote control
⇒
page 50 and then
open the driver door.
– The seat and exterior mirrors now move automatically into the stored
positions.
Retrieving setting of exterior mirror for reversing* – Turn the rotary knob for the exterior mirror setting into the position

⇒
page 73 before engaging the reverse gear.
The mirror returns into its initial position,
after the rotary knob is moved out of the
position
 and put into another position or if the speed is more than 15 km/h.
Emergency Off You can interrupt the setting operation at any time, if you operate any button of the driver seat.
Note
If in the stored position the inclination an
gle of the seat backrest is more than 102°
in relation to the seat cushion, the seat backrest remains in this position, after reaching this angle, when
retrieving the setting by briefly pressing the memory
button. In order to achieve the stored setting, it is necessary to press the memory button again and hold it pressed until the seat is in the stored position.
Head restraintsBest protection is achieved if the top edge of the head restraint is at the same level as the uppe
r part of your head.
Adjusting the height of a head restraint – Grasp the side of the head restraint with both hands and push it in
upward direction as desired
⇒
fig. 77
.
– Move the head restraint downward
s if required by pressing and
holding the safety button with one hand
⇒
fig. 78
and by pressing
with the other hand the head restraint downwards.
Fig. 77 Adjusting head restraintFig. 78 Removing a head restraint
se0.1.book Page 79 Friday, April 10, 2009 3:19 PM