warning lights SKODA OCTAVIA TOUR 2010 1.G / (1U) Columbus Navigation System Manual

Instruments and warning lights
24
The red symbols indicate danger (priority 1) while the yellow symbols indicate a
warning (priortity 2). Information for the driver may also appear in addition to the
symbols page 25.
Investigate the displayed faults as soon as po ssible. If several operational faults exist at
the same time, the symbols will appear one after the other and are each visible for
about 2 seconds.
The error messages are faded out after 10 seconds or by actuating the rocker switch
 page 23, fig. 25 and are stored under the information CAR STATUS.
There is at least one error message to be read when the term CAR STATUS is flashing
in the menu. In the display STATUS 1/2 lights up, for example, if a number of error
messages are present. This display indicates that the first of a total of two error
messages should be displayed.
Actuate the rocker switch , to call up the individual error messages.
If a fault occurs, a warning signal will also sound in addition to the symbol and text in
the display:
Priority 1 - three warning signals

Priority 2 - one warning signal
Red symbols
A red symbol signals danger.Proceed as follows if a red symbol is displayed:
– Stop the vehicle.
– Switch the engine off.
– Check the functions indicated.
– Obtain professional assistance.
Meaning of the red symbols: Three
successive warning signals will sound if a red symbol appears. The symbol
continues flashing until the fault is rectified.
If several operational faults of priority 1 exist, the symbols appear one after the other
and are each illuminated for about 2 seconds.
Yellow symbols
A yellow symbol signals a warning.The meaning of the yellow symbols:
One warning signal will sound if a yellow symbol appears.
If several operational faults of priority 2 exist, the symbols appear one after the other
and are each illuminated for about 2 seconds.
Check the relevant function as soon as possible.
AA
AA

Faults in the brake surface
 page 31

Coolant level too low/c oolant temperature too
high
 page 28

Engine oil pressure too low
page 29

Fuel level low
page 29

Check engine oil level, engine oil sensor faulty
page 29

Brake pad worn
page 29

Washer fluid level low
page 29

faulty bulb
page 27
s2rc.book Page 24 Thursd ay, April 22, 2010 10:58 AM

Instruments and warning lights25
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Warning lightsOverview
The warning lights indicate certain functions or faults.
Fig. 26 Instrument cluster with warning lights

Turn signal lights (to the left)
page 26

Turn signal lights (to the right)
page 26

Turn signal system for vehicles towing a
trailer*
page 26

Main beam light
page 26

Low beam light
page 26

Fog lights*
page 27

Rear fog light
page 27

Electronic immobiliser
page 27

Bulbs*
page 27

Control system for exhaust
page 27

EPC fault light* (petrol engine)
page 27

Glow plug system (diesel engine)
page 27

Airbag system*
page 28

Coolant temperature/coolant level
page 28
s2rc.book Page 25 Thursd ay, April 22, 2010 10:58 AM

Instruments and warning lights
26WARNING

If you do not pay attention to the warning lights coming on and the corre-
sponding descriptions and warning notes, this may result in severe body inju-
ries or major vehicle damage.

The engine compartment of your car is a hazardous area. There is a risk of
injuries, scalding, accident s and fire when working in the engine compartment,
e.g. inspecting and replenishing oil and other fluids. It is also essential to
observe all warnings page 148.
Note

Arrangement of the indicator lights depends on the model and model version. The
symbols shown in the following functional description are to be found as indicator
lights in the instrument cluster.

Operational faults are shown in the instrument cluster as red symbols (priority 1 -
danger) or yellow symbol s (priority 2 - warning).
Turn signal system

Either the left
 or right
 indicator light flashes depending on the position of the turn
signal lever.
The indicator light flashes at twice its normal rate if a turn signal light fails. This does
not apply when towing a trailer.
Switching off the hazard warning light system is switched on will cause all of the turn
signal lights as well as both indicator lights to flash.
Further information about the turn signal system page 49.
Turn signal system for vehicles towing a trailer

*
The warning light
 flashes together with the other turn signal lights only if the vehicle
is towing a trailer.
The indicator light does not flash if a turn sign al light on the trailer or on the vehicle is
not operating.
Main beam

The indicator light
 comes on when the main beam is selected or also when the
headlight flasher is operated.
Further information about the main beam page 49.
Low beam

The warning light
 comes on when low beam is selected page 46.

Brake pad wear*
page 29

Fuel reserve
page 29

Engine oil
page 29

Open door*
page 30

Fluid level in windshield washer system*
page 29

Antilock brake system (ABS)*
page 30

Traction control system (TCS)*
page 31

Electronic stability programme (ESP)*
page 31

Dynamo
page 31

Brake system
page 31

Seat belt warning light*
page 32
s2rc.book Page 26 Thursd ay, April 22, 2010 10:58 AM

Instruments and warning lights27
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Fog lights
*
The warning light
 comes on when the fog lights are operating.
Rear fog light

The warning light
 comes on when the rear fog lights are operating page 47.
Electronic immobiliser

Data is compared between the ignition key and the control unit when switching on the
ignition. The indicator light

will light up for a few seconds when ignition key
authorisation is confirmed.
The warning light will start flashing continuous ly if a non-authorised ignition key (for
example the wrong ignition key) has be en used. The engine cannot be started
 page 34.
It is only possible to start the engine of the vehicle with a Genuine Škoda key with the
matching code.
The following text will be displayed in the information display*:
IMMOBIL. ACTIVATED
Bulbs

The warning light
 comes on if a bulb is faulty:

Brakes applied (brake light);

Switching on the lights (front low beam or rear parking lights).
A peep sounds as an additional warning signal.
Control system for exhaust

The warning light
 comes on after the ignition has been switched on.
If the warning light does not go out after star ting the engine or it lights up or flashes
when driving, a fault exists in an exhaust relevant component. The engine manage- ment system selects an emergency programme which enables you to drive to the
nearest specialist garage by adopting a gentle style of driving.
The following text will be displayed in the information display*:
EMISSIONS WORKSHOP!
EPC fault light

(petrol engine)
The
 (Electronic Power Control) warning light comes on for a few seconds when the
ignition is switched on.
If the warning light
 does not go out or lights up after starting the engine, a fault
exists in the engine control. The engine management system selects an emergency
programme which enables you to drive to the nearest specialist garage by adopting a
gentle style of driving.
The following text will be displayed in the information display*:
ENGINE WORKSHOP!
Glow plug system

(diesel engine)
The warning light
 lights up for a cold engine when switching on the ignition (pre-
heat position) 2  page 87. Start the engine just as s oon as the indicator light goes out.
The glow plug indicator light will come on for about 1 second if the engine is at a
normal operating temperature or if the outside temperature is above +5°C. This
means that you can start the engine right away.
There is a fault in the glow plug system if the warning light
 does not come on at
all or lights up continuously . Contact a specialist garage as soon as possible to obtain
assistance.
If the warning light
 begins to flash while driving, a fault exists in the engine control.
The engine management syst em selects an emergency programme which enables you
to drive to the nearest specialist garage by adopting a gentle style of driving.
The following text will be displayed in the information display*:
ENGINE WORKSHOP!
s2rc.book Page 27 Thursd ay, April 22, 2010 10:58 AM

Instruments and warning lights
28
Airbag system

Monitoring the airbag system
The warning light
 comes on for a few seconds when the ignition is switched on.
There is a fault in the system if the warning light does not go out or comes on or flashes
while driving  . This also applies if the warning light does not come on when the
ignition is switched on.
The following text will be displayed in the information display*:
AIRBAG FAULT
The functionality of the airbag system is also monitored electronically when one airbag
has been switched off.
Front airbag or side passenger airbag deactivated using the diagnostic equip-
ment:

The warning light
 lights up for 3 seconds after switching on the ignition and then
flashes again for 12 seconds.
The following situation applies if the ai rbag has been switched off using the
switch for the airbag* in the storage compartment:

The warning light
 comes on for 3 seconds after the ignition has been switched
on.

The deactivation of the airbag is indicated by the lighting up of the indicator light

 in the interior lighting page 113.WARNING
Have the airbag system checked immediat ely by a specialist garage if a fault
exists. Otherwise, there is a risk of the airbag not being activated in the event of
an accident.
Note
Further information about switching off airbags page 113.
Coolant temperature/coolant level

The warning light  comes on for a few seconds
2) when the ignition is switched on.
The coolant temperature is too high or the coolant level too low if the warning light

does not go out or flashes while driving.
3 peeps sound as an additional warning signal.
In this case stop and switch the engine off and check the coolant level; top up the
coolant as necessary.
Do not continue your journey if for some reason it is not possible under the condi-
tions prevailing to top up with coolant. Keep the engine switched off and obtain
professional assistance from a specialist garage, otherwise it could lead to severe
engine damage.
If the coolant is within the specified range, the increased temperature may be caused
by an operating problem at the coolant fan. Check the fuse for the coolant fan, replace
it if necessary page 178, “Fuse assignment in engi ne compartment - version 1” or
 page 179, “Fuse assignment in engine compartment - version 2”.
Do not continue driving if the warning light does not go off although the fluid is at the
correct level and also the fuse of the fan is in proper order. Contact a specialist garage
to obtain assistance.
Please refer to the following guidelines page 152, “Cooling system”.
The following text will be displayed in the information display*: STOP CHECK COOLANT SERVICE MANUAL
WARNING

If you must stop for technical reasons, then park the vehicle at a safe
distance from the traffic and switch of f the engine and switch on the hazard
warning light system  page 48.

Take care when opening the coolant expa nsion bottle. If the engine is hot,
the cooling system is pressurized - risk of scalding! It is best to allow the engine
to cool down before removing the cap.
2)The warning light  on vehicles fitted with information display does not come on after switching
the ignition on, but only if the coolant temperature is too high or the coolant level is too low.
s2rc.book Page 28 Thursd ay, April 22, 2010 10:58 AM

Instruments and warning lights29
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data

Do not touch the coolant fan The coolant fan may switch on automatically
even if the ignition is off.
Thickness of the brake pads*

The warning light
 comes on for a few seconds when the ignition is switched on.
If the warning light  comes on, contact a specialist garage immediately and have the
brake pads on all of the wheels inspected.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*: CHECK BRAKE PADS
Windshield washer fluid level*

The warning light
 comes on when the ignition is swit ched on if there is insufficient
fluid in the windshield washer system. Top up with liquid page 159.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*: TOP UP WASH FLUID
Fuel reserve

The warning light
 comes on, if the fuel level is still below 7 litres.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*: PLEASE REFUEL
Note
The Text in the information display* goes out only after refuelling and driving a short
distance.
Engine oil

The warning light

lights up red (low oil pressure)
The warning light comes on for a few seco nds when the ignition is switched on
3).
Stop the vehicle and switch the engine off if the warning light does not go off within
a few seconds after switching on the ignition or flashes while driving. Check the oil
level and top up with oil as necessary page 151.
3 peeps sound as an additional warning signal.
Do not continue your journey if for some reason it is not possible under the condi-
tions prevailing to top up with oil. Keep the engine switched off and obtain profes-
sional assistance from a specialist garage, otherwise it could lead to severe engine
damage.
Do not drive any further if the warning light remains on even if the oil is at the correct
level. Do not run the engine not at idling speed either. Contact the nearest specialist
garage to obtain professional assistance.
The following text will be displayed in the information display*:
STOP! OIL PRESS. STOP MOTOR! SERVICE MANUAL
The warning light

lights up yellow* (oil quantity too low)
If the warning light lights up yellow, there is not the correct quantity of oil in the engine.
Check as soon as possible the oil level or top up page 151 with engine oil.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*: CHECK OIL LEVEL
When opening the bonnet, the warning light goes out. If no engine oil has been replen-
ished, the warning light will come on again after driving about 100 km.
The warning light

flashes yellow* (engine oil level sensor faulty)
A fault on the engine oil level sensor is indicated additionally by an audible signal and
the warning light coming on several times after the ignition has been switched on.
WARNING (continued)
3)The warning light  on vehicles fitted with information display does not come on after switch-
ing the ignition on, but only if a fault exists or the engine oil level is too low.
s2rc.book Page 29 Thursd ay, April 22, 2010 10:58 AM

Instruments and warning lights
30
In this case have the engine inspected without delay by a specialist garage.
The following text will be displayed in the information display*:
OIL SENSOR WORKSHOP!
WARNING

If you must stop for technical reasons, then park the vehicle at a safe
distance from the traffic and switch off the engine and switch on the hazard
warning light system page 48.

The red oil pressure light

is not an oil level indicator! One should there-
fore check the oil level at regular inte rvals, preferably after every refueling
stop.
Open door*

The warning light
 comes on, if one or several doors are opened.
The warning light on vehicles fitted with information display comes on when switching
the ignition off. If a door or the boot lid is opened.
The warning light on vehicles fitted with information display goes out after switching
the ignition off.
Antilock brake system (ABS)*

The warning light
 shows the functionality of the ABS and the Electronic Differential
Lock (EDL)*.
The warning light comes on for a few seconds after the ignition has been switched on
or when starting the engine. The warning light goes out after an automatic check
sequence has been completed.
A fault in the ABS
The system is not functioning properly if the ABS warning light
 does not go out
within a few seconds after switching on the ignition, does not light up at all or lights up
while driving. The vehicle will only be br aked by the normal brake system. Visit a
specialist garage as quickly as possible and adjust your style of driving to take account of the fault in the meantime since you will no
t know the extent of the fault and in how
far the effect of the antilock brakes is affected.
Further information about ABS page 126, “Antilock brake system (ABS)*”.
A fault in the entire brake system
If the ABS warning light
 comes on together with the brake system warning light

(handbrake must be released), there is a fault not only in the ABS but also in another
part of the brake system .
Electronic Differential Lock (EDL)*
The EDL is a part of the ABS. A fault in the EDL is indicated by the lighting up of the ABS
warning light
 in the instrument cluster. Have the vehicle inspected immediately by
your nearest specialist garage.
Models fitted with ESP are equipped with electronic differential lock (EDL).
If a significant fault occurs in the ABS syst em, a warning signal sounds additionally (3
peeps).
Further information on the EDL page 124.
WARNING

If the brake system warning light
 comes on together with the ABS
warning light
 stop the vehicle immediately an d check the brake fluid level in
the reservoir page 154, “Brake fluid”. If the fluid level has dropped below the
MIN marking, do not drive any further - risk of accident! Obtain professional
assistance.

Pay attention to the following instruct ions before checking the brake fluid
level and opening the bonnet page 148, “Working in the engine compart-
ment”.

If the brake fluid is at the correct leve l, the ABS control function has failed.
The rear wheels may then block very rapi dly when braking. In certain circum-
stances, this can result in the rear end of the car breaking away - risk of skid-
ding! Drive carefully to the nearest sp ecialist garage and have the fault
rectified.
s2rc.book Page 30 Thursd ay, April 22, 2010 10:58 AM

Instruments and warning lights31
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Traction control system (TCS)*

The warning light
 comes on for a few seconds when the ignition is switched on.
The warning light flashes when a control cycle is activated while driving.
The warning light will come on and remains on if the TCS is switched off or if there is a
fault in the system.
The fact that the TCS system operates together with the ABS means that the TCS
warning light will also come on if the ABS system is not operating properly.
If the warning light  comes on immediately after starting the engine, the TCS system
can be switched off for technical reasons. In this case, the TCS system can be switched
on again by switching the ignition on and off. If the warning light goes out, the TCS
system is fully functional again.
Further information about the TCS page 125, “Traction control system (TCS)”.
Electronic stability programme (ESP)*

The warning light
 comes on for a few seconds when the ignition is switched on.
Components of the ESP system also include the Traction Control System (TCS), the
Electronic Differential Lock (EDL) and the Antilock Brake System (ABS).
The warning light flashes when a control cycle is activated while driving.
The warning light will come on and remains on if the ESP is switched off or if there is a
fault in the system.
The fact that the ESP system operates together with the ABS and the EDL means that
the ESP warning light will also come on if the ABS system is not operating properly.
If the warning light  comes on immediately after starting the engine, the ESP system
can be switched off for technical reasons. In this case, the ESP system can be switched
on again by switching the ignition on and off. If the warning light goes out, the ESP
system is fully functional again.
Further information on the ESP page 123, “Electronic stability programme (ESP)*”.
Note
If the battery has been disconnected and reconnected, the warning light
 comes on
after switching on the ignition. The warning light must go out after driving a short
distance.
Alternator

The warning light
 comes on after the ignition has been switched on. It should go
out after the engine has started.
If the warning light does not go out after the engine has started, or comes on when
driving, drive to the nearest specialist garage. The vehicle battery will be discharged in
this case so switch off all non-essential electrical components.
A peep sounds as an additional warning signal.
Caution
If the warning light
 comes on when driving and in addition the warning light

(cooling system fault) also comes on in di splay, you must then stop the car immedi-
ately and switch the engine off - risk of engine damage!
Brake system

The warning light
 comes on for several seconds afte r the ignition is switched on.
If the warning light  stays on when the ignition is switched on or comes on while
driving, there is a fault in the brake system. Visit the nearest specialist garage immedi-
ately and have the brake system inspected.
The following text will be displayed in the information display*:
STOP BRAKE FLUID SERVICE MANUAL
3 peeps sound as an additional warning signal.
One should get used to high pedal forces, long braking distances and long free play of
the brake pedal when driving to the next specialist garage.
For further information on the brake system page 125, “Brakes”.
s2rc.book Page 31 Thursd ay, April 22, 2010 10:58 AM

Instruments and warning lights
32
Handbrake applied
The warning light
 also comes on if the handbrake is applied. An audible warning is
also given if you drive the vehicle for at least 3 seconds at a speed of more than 5 km/h.
The following text will be displayed in the information display*:
HANDBRAKE ON
WARNING

Pay attention to the following instruct ions before checking the brake fluid
level and opening the bonnet page 148, “Working in the engine compart-
ment”.

If the brake system warning light
 does not go out a few seconds after
switching on the ignition or comes on when driving, stop immediately and
check the brake fluid in the reservoir page 154, “Brake fluid”. If the fluid level
has dropped below the MIN marking, do no t drive any further - risk of accident!
Obtain professional assistance.
Seat belt warning light*

The warning light
 comes on after the ignition is switched on as a reminder to fasten
the seat belt.
In the event that the driver is not restrained, a warning signal sounds for 6 seconds.
The following text will be displayed in the information display*:
FA S T E N S E AT B E LT
Further information on the seat belts page 102, “Seat belts”.
s2rc.book Page 32 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking37
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Unlocking the vehicle using the key– Turn the key in the locking cylinder of th e driver's door to the left in the unlock
position fig. 32 .
– Pull on the door handle and open the door.
All the doors are unlocked.

The boot lid is then unlocked.

The switched on interior lights come on over the door contact.

The safe securing system is deactivated.

The windows open provided the key is held* in the unlock posi tion. On vehicles
fitted with anti-theft alarm system the wi ndow operation is only possible 45 seconds
after deactivation of the warning system.

The indicator light in the driver's door stop s flashing if the vehicle is not fitted with
an anti-theft alarm system* page 40.Note
If the vehicle is equippe d with an anti-theft alarm system*, you must insert the key into
the ignition lock and switch the ignition on within 15 seconds after unlocking the door
in order to deactivate the anti-theft alarm system. The alarm will be triggered if you
do not switch on the ignition within 15 seconds.
Locking the vehicle with the key– Turn the key in the locking cylinder of the driver's door to the right in the lock posi-
tion fig. 32 .
All the doors and the boot lid are locked.

The switched on interior lights will switch off over the door contact.

The windows and the electric sliding/ti lting roof* close provided the key is held in
the lock position.

The safe securing system is activated immediately.

The indicator light in the dr iver door begins flashing.Note
The opened driver door cannot be locked. It must be locked separately after closing
it.Button for the central locking systemIf the vehicle is not locked from outside, you can unlock an d lock the vehicle with the
button in the driver door.Locking all doors and the boot lid– Press button fig. 33 . The symbol
 in the button comes on.
Fig. 32 Turning the key for
unlocking and locking the
vehicle
AA
AB
Fig. 33 Button for the central
locking system
A1
s2rc.book Page 37 Thursd ay, April 22, 2010 10:58 AM