lock SKODA SUPERB 2009 2.G / (B6/3T) Amundsen Navigation System Manual

General information
5
But you should only operate the navigation system with its wide range of possibilities when the traffic situation allows. The volume settings must be selected in
such a way that audible signals from the
outside, e.g. a Martins horn from utility
vehicles (police cars, ambulances and fire
brigade), can be heard at all times.
WARNING
Please concentrate fully at
all times on your driving! As the driver you are
fully responsible for road safety. Only use the functions in such a way that you are always in full control of your vehicle in all traffic situations!Before using the navigation system•
Please observe the respective traffic regulations when driving.
•
Street and location names can be change
d. It is therefore possible that the
names stored on the CD might not correspond to the changed names.•
The route calculated by the navigation system is a recommendation for
reaching the intended destination. While
driving please pay a
ttention to stopping
restrictions, traffic lights, one-way streets, lane change restrictions, canals and ferries.
WARNING
Road traffic legislation (StVO) applies
at all times, even if a driving recom-
mendation contradicts the StVO.
Caution
•
Inserting a second CD while a CD is being ejected can destroy the CD drive in
the unit. Please note that the CD ejecti
on lasts a few seconds after pressing the
Eject button
. During this time the lock in fr
ont of the CD case is open. It is
essential that you wait until the CD has been
fully ejected before you try to insert a
new CD.
•
Press the buttons and the keys of the unit gently in order to avoid damaging
them. Gentle pressure on
the appropriate key is sufficient to operate the unit.
Please note that the contro
l buttons have predetermined
breaking points, in order
to reduce the risk of injury.•
Do not use any pointed or sharp-edged objects to operate the touch-screen.
Slight finger pressure sufficient to oper
ate the equipment. A display on the screen,
which cannot be called up by pressing the bu
tton, is therefore not available at that
time.•
Please note that a dirty or scratched na
vigation CD can considerably impair the
speed and the functions of the navigation system.Screen careTreat the screen with great care, becaus
e dents and scratches can occur through
finger pressure or contact with sharp objects. The screen can be cleaned with a soft cl
oth and finger marks can be wiped away
with pure alcohol.
Note
Do not use solvent such as turpentine or
petrol as they will attack the screen
surface.Anti-theft protectionThe anti-theft coding of
your navigation system prevents an operation of
the system after a voltage interruption,
e.g. during a vehicle repair or after
theft. After disconnecting the batt
ery, disconnecting the navigation
system from the on-board voltage of the vehicle and after a fuse failure, the code must be entered before the vehicle can be used again.
š
s36c.b.book Page 5 Thursday, April 9, 2009 2:50 PM

General information
6 Enter code – If a keypad appears after switching on with the command to enter the
code, the unit can be unlocked by en
tering the correct four-digit code
number. The number of the possible attempts is shown in the bottom screen line.
– Press a digit from to on the digit block displayed on the screen.
The digit is accepted in the entry line.
– After a four-digit order has been entered, the group of digits will turn
grey (inactive) and no further digits can be accepted in the entry line.
– Press on the screen in order to delete the digits in the entry line
from right to left and thereby correct your input, if necessary.
– If the correct code number is displayed in the entry line, press .Code number The code number can only be called up “onl
ine” via the Škoda system, as this guar-
antees even more effective anti-theft protection. Please contact your authorized Škoda Service Partner, if necessary. Incorrect code number If an incorrect code is confirmed after entry of the code, the procedure can be repeated
twice
. The number of possible attempts
is shown in the bottom screen
line. If the code number is entered incorrectly for the third time, the unit will be blocked for approx. one hour. It is possible to ente
r again the safety code after one hour has
expired, when the unit and the ig
nition have been switched on.
If three invalid attempts are then made agai
n, the navigation system will be blocked
again for an hour. The cycle - three attempts, blocked for
an hour - will continue to apply.
Note
The code is normally stored in the instrume
nt cluster. This ensures that it is auto-
matically decoded (convenience coding). Ma
nual input of the code is normally not
necessary.
0
9
Delete
OK
s36c.b.book Page 6 Thursday, April 9, 2009 2:50 PM

General information
7
Operation when driving The demands of today's road traffic require full concentration from all road users at all times.
WARNING
•
Always concentrate fully on your driv
ing. Inattention by the driver can
lead to accidents and injuries.•
Do not allow yourself to be distracted by trying to use the unit, concen-
trate instead on the traffic situation.•
Use the unit only if road, weather and traffic conditions permit and you
will not be distracted.•
The various volume settings must be selected in such a way that audible
signals from the outside, su
ch as e.g. a Martins horn from police cars and fire
brigade, can be heard at all times.
Note
Depending on the country, some functions
of the radio navigation system can no
longer be selected on the screen at cert
ain speeds. This is not a malfunction, but
corresponds to the legal requirem
ents of this particular country.
Special functionsParking aid* If your vehicle is equipped wi
th “parking aid” and after it is activated, the distance
to the obstacle is shown on the screen. Climatronic* If your vehicle is equipped with climatroni
c, a feedback is received on the screen
when changing the settings.
Personalisation Your vehicle can be eq
uipped with up to four keys. Ind
ividual settings of the unit are
always assigned to the key,
which is currently inserted in the ignition lock. In prac-
tice, this means that each time you use another vehicle key, the setting of the unit which is assigned to the key is carried out.Switching the system on and off– The system is switched on or off by pressing the control button .The last active audio source before switching off is repeated. If the key is pulled out of the ignition lock while the unit is switched on, the unit will switch off automatically. You can then switch
the unit on again. If the ignition is
switched off, the system switches off au
tomatically after approx. half an hour
(vehicle battery protection
against discharging). This pr
ocess can be repeated as
often as necessary.General - operationThe screen of the unit is a so-calle
d touch screen (touch-screen). Fields
circled in colour on the touch-screen
are presently “active” and are oper-
A1
BAT-20H1069
Fig. 2 Menu radio
s36c.b.book Page 7 Thursday, April 9, 2009 2:50 PM

General information
8 ated by touching the screen. Active
fields, which call up a function or a
menu, are called “
function buttons
” / .
The following information is displayed in the main menu: the selected radio station (i
ts frequency or
designation);
selected waveband; activation for the rece
ption of traffic reports;
current menu. “Pop-up window” If you press the function key on the sc
reen, a so-called “pop-up window” will
open where all possible se
t-up options are displayed.
Briefly press the desired set-up option. Th
e pop-up window will disappear and the
newly selected set-up option is
displayed in the function key.
“Check box” Some functions can only
be switched on or off.
There is a so-called “check box” in front of a function which can only be switched on or off. A tick in the check box
7 indicates that the functi
on is switched on, an
empty check box
8, indicates that it
is switched off.
Briefly press the corresponding function key for switching on or off.
Input mask for free text inputIn some of the menus you can enter a free text, for example, when entering a new destination or while se
arching for the name of a point of
interest. – Press to accept a character se
quence offered by the system or
press in order to delete the characters in the entry line.
– When in the entry window, press on a character shown on the keypad
block to accept it into the entry line.
– You can also delete or change the character sequence in the entry line
as well as insert additional characters.
Further input possibilities: - changes from upper case to lower case and vice versa. - opens the input mask for digits an
d special characters. The function key
changes to . Press , to change again to the letter input mask.˜ - space key for entering spaces. or - moves the character entry cursor (the cursor) in the entry line to the left or right.
- opens a pop-up window with special characters.
AD
AF
AAABACAE
AF
BAT-20H1085
Fig. 3 Input mask for free text input
OKDelete
45
A-Z
A-Z
‚
b
ÄÜ
s36c.b.book Page 8 Thursday, April 9, 2009 2:50 PM

Range selector key MEDIA
17
Range selector key MEDIAGeneral information for CD operationAudio-CDs (CD-A) and MP3-CDs can be
played in the internal drive.
CD not legible If you insert a CD which cannot be read by
the unit, a pop-up window is displayed
with a note. Press on the function key , the CD is driven to the initial position. If the CD is not taken out within 10 seconds, it is drawn in again for safety reasons.
WARNING
•
The CD player is a 1st class laser produc
t. There is a definite risk of injury
from invisible laser beams if it is opened.•
The CD player contains no parts that have to be serviced or repaired.
Please contact your speciali
st garage if a mechanical
defect occurs or the CD
player has to be repaired.
Caution
•
Inserting a second CD while a CD is being ejected can destroy the CD drive in
the unit. Please note that the CD ejecti
on lasts a few seconds after pressing the
Eject button
. During this time the lock in fr
ont of the CD case is open. It is
essential that you wait until the CD has been
fully ejected before you try to insert a
new CD.•
If the CD drive becomes me
chanically defective or
a CD has been inserted
incorrectly or not fully, “
Fa u l t : ° C D
” will be displayed on the screen. Please check the
CD and place it again correctly and fully into the drive. If “
Fa u l t : ° C D
” is indicated
again, please contact your Škoda Service Partner.•
If the inside temperature of the unit is
too high, no CDs will be accepted. The
unit switches into the last active operating mode.
Note
•
If the function key is inactive, no
new Audio CD has been inserted or an
inserted Audio CD is not readable.•
It is possible that CDs protected by copyright and self-made CD-R and CD-RW
are not returned at all or on
ly in certain circumstances.
•
Please observe the following information for the MP3 operation
⇒page 20.
•
Please comply with the national legal copyright requirements in your country.
Main menu MEDIAMain menu MEDIA - Overview
OK
š
CD
BAT-20H1065
Fig. 9 Main menu MEDIA: CD

mode
s36c.b.book Page 17 Thursday, April 9, 2009 2:50 PM

Range selector key MEDIA
18
Calling up the main menu MEDI
A and changing the media source
– Press the range selector key to switch to the main menu
MEDIA
. The last used audio source will continue to play.
Buttons on the unit for controlling the current audio sources The arrow keys on unit or will always affect the currently heard audio source, irrespective of the current menu used. - briefly press to go to the beginning of
the current track, press repeatedly to
return to the beginning of the previous track. - brief pressing changes over to the beginning of the next track.When in the menu of the currently played audio source it is also possible to change titles using the setting up button. - by briefly pressing, you can select the display for the additional information of the audio sources. Selectable audio sources in the menu AUDIO
CD - changes over to an inserted CD. CD 1-6
* - changes over to a connected external CD changer.
SD card
- changes over to an inserted memory card.
, or * - changes over to a connected external audio source.
Operating an externally connected audio
source is possible, wi
th certain restric-
tions, via the radio navigation unit and depends largely on the type of the connec- tion. Additional function keys in the AUDIO menu
- opens a pop-up window wher
e the random play function
Mix
, the auto-
matic play
Scan
or the replay of the track or the folder can be started.
- opens the list of the tracks for the current audio source in order to select
another track.Inserting or ejecting a CDInserting the CD – Push a CD with the written side facing
up as far as po ssible into the CD
case until it is automatically drawn in
. The play function will start auto-
matically.
Taking out the CD – Press the button to move the CD
in the internal CD drive into the
Eject position.
If a CD is not taken out in the initial position, it will be reinserted after approximately 10 seconds for safety reasons.Inserting or removing a memory cardInserting a memory card – Push the memory card into the me
mory card case with the trimmed
edge to the front top, until it is locked in position. The play function will start automatically.
Taking out a memory card – Press the button and then the function key .
BAT-20H1066
Fig. 10 Selectable sources in

the menu MEDIA
MEDIA
ƒ
„
ƒ„ºFFF

HAUX
MDI
BT audio
ExtrasSelect
šSETUP
System
s36c.b.book Page 18 Thursday, April 9, 2009 2:50 PM

Range selector key NAV (Navigation)
31
– Press the button and then the function key
while in the main menu
Navigation
.
– Press on the function key . – You can determine which types of destinations should be provided or
not by using the function keys , and . These types of destinations will, however, be used for the route calculation if th
ere is no other logical route to the
destination (e.g an island is to be used without using a ferry).
Determining the parameters for the route calculation•
Fa st
: It calculates the fastest route to your
destination, even if a detour is neces-
sary.•
Short
: Longer driving time in favour of a shorter route is acceptable. Please
note that the setting “Short route” during route guidance can sometimes lead to unexpected results.•
Economical
: The aim of the calculation is
a balance between
minimal driving
time and driving distance.Route guidance
Select the destination and start the route guidance. The unit will switch over to the map display. – You can change the scale of the map display by turning the menu
control button .
– The last navigation announcement
is repeated if you press the menu
control button .
– You can change between the main menu
Navigation
or the map
display by pressing the range control button .
The route to be driven is highlighted
during the route guidance, the symbol
3
shows the current vehicle position, the symbol
 shows the distance to the desti-
nation and the symbol
 shows the estimated time of arrival or the driving time.
Stretches of the road ahead can also be
blocked manually during a route guidance
⇒ page 32.Stopping the route guidanceSelect the destination and start the route guidance. The unit will switch over to the map display.
SETUP
Route options
Route criteria
˜ Dynamic route
˜ Avoid motorways
˜ Avoid toll roads/ferry
BAT-20H1126
Fig. 18 Map display with function keys
Fig. 19 Map display during the route guidance
A10A10
NAV
s36c.b.book Page 31 Thursday, April 9, 2009 2:50 PM

Range selector key NAV (Navigation)
32
– The route guidance is interrupted
and the function key changes to
“ Start
” by pressing the range control button and then the func-
tion key .
– If you press on the function key
the route guidance will continue
at the current position.
Inserting routenlistThe routenlist for the trip can only be displayed during a route guidance. Additional window in the map display – An additional window opens if you press the button during the
route guidance.
– Select the function key in the additional window. The
routenlist is displayed. The list of the points (street names, street descriptions and stretches of the road
) still to be driven, is displayed
in the
Routenlist
.
– In addition, the distance still to be driven on the driven road and the
estimated time to the following turning point are displayed.
Manually excluding a stretch of the road – You can select the beginning of the
stretch of the road to be excluded
by using the control button .
– Press on the function key , this changes to the function key
.
– Select the end of the stretch of the
road to be excluded and select the
function key .
– The route is newly calculated. – If you wish to cancel the exclusion of the stretch of the road, press the
function key .
Dynamic route guidance with TMC use Switching the dynamic navigation on or off – Press the button and then select the function key
while in the main menu
Navigation
.
– In the menu
Route options
, activate the check box
and select the desired set-up by pressing your choice in the pop-up window.
Requirements for a dynamic route guidance TMC (Traffic Message Channel) is a digital radio data service for
continuous
trans-
mission of traffic information. The unit has a continuous background of
TMC traffic reports providing a TMC
station at the current location can be received. The quality of the transmitted traffic reports depends on the broadcast editing carried out by the radio station. The reception of the TMC traffic reports cannot be switched on or off. The station you are listening to do
es not have to be a TMC station.
TMC traffic reports can only be evaluated an
d displayed by the unit if the navigation
data for the currently driven area is stored
in the unit memory or can be called up
via an inserted navigation CD. The current TMC traffic reports can be displayed by pressing the selector key
.Note
•
There may not be any advantage in avoiding the traffic jam if, as a result of the
TMC traffic reports, the divers
ion is also heavily congested.
•
You can manually block the information for the route in front of you if traffic
problems ahead have not yet been in
cluded in the TM
C traffic reports
⇒page 32.
NAV
Stop
Start
º
Routenlist
A1Exclude
Exclude to
Exclude toCancel
SETUP
Route options
˜ Dynamic route
TRAFFIC
s36c.b.book Page 32 Thursday, April 9, 2009 2:50 PM