key SKODA SUPERB 2009 2.G / (B6/3T) User Guide
[x] Cancel search | Manufacturer: SKODA, Model Year: 2009, Model line: SUPERB, Model: SKODA SUPERB 2009 2.G / (B6/3T)Pages: 294, PDF Size: 21.33 MB
Page 49 of 294
Unlocking and locking
48
Emergency locking of the doorsAn emergency locking mechanism is located on the face side of the doors which have no locking cylinder, it is only visible after opening the door. Lock the doors using the vehicle key. Locking – Remove the panel
⇒
fig. 42
.
– Guide the key into the slot and turn it to the outside. – Re-insert the panel.After closing the door, you can no longer op
en it from outside. If the child safety
lock is not switched on, it is possible to open the door from the inside by pulling on the door handle. If the child sa
fety lock is switched on, it is necesary to also open
the door from outside besides pulling on the inner door handle.
Twindoor - small boot lidAfter unlocking the vehi
cle using the radio remote control or the key
⇒
page 47 you can open the small boot lid
⇒
fig. 44
.
Open small boot lid – Press on the handle at the bottom side of the boot lid
⇒
fig. 43
, the
boot lid lifts up automatically
⇒
fig. 44
.
Close small boot lid – Pull the boot lid down and close it with a slight swing
⇒
. The
bonnet locks automatically.
Fig. 42 Rear door: Emer- gency locking of the door
Fig. 43 Handle of boot lidFig. 44 Boot lid
s2dk.1.book Page 48 Wednesday, April 8, 2009 12:23 PM
Page 50 of 294
Unlocking and locking
49
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
You can also open the small boot lid by pressing the button on the remote control
⇒page 51 for approx. 2 seconds.
A handle which makes the clos
ing easier is located on
the inner paneling of the
boot lid.
WARNING
•
Ensure that the lock is properly enga
ged after closing the boot lid. Other-
wise, the boot lid might open suddenly wh
en driving even if the boot lid lock
is closed - risk of accident!•
Never drive with the boot lid fully opened or slightly ajar otherwise
exhaust gases may get into the interior of the vehicle - risk of poisoning!
Hinweis
•
After closing the boot lid, it is automatically locked within 2 seconds and
the anti-theft alarm system* is activated.
This applies only if the vehicle was
locked before closing the boot lid.•
The function of the hand grip on the bottom edge of the boot lid is deactivated
when starting off or as of a speed of more
than 5 km/hour. The function of the hand
grip is acitvated again after stopping the vehicle and after opening the driver or front passenger door or after pressing th
e button on the radio remote control
⇒ page 51.•
Repeated opening and closing of the boot
lid can lead to a temporary failure of
the function due to the overheating prot
ection of the motors of the Twindoor
system.
Twindoor - large boot lidAfter unlocking the vehicle using the radio remote control or the key ⇒
page 47, “Emergency unlocking and lo
cking of the driver's door” you
can open the large boot lid
⇒
fig. 46
.
Open large boot lid – Press the handle
⇒
fig. 45
on the bottom edge of the boot lid.
– Yo u must wait until the brake light in the rea r window f lashes twic e. – Press on the handle and at the same time raise the boot lid.
A2
A1
Fig. 45 Handle of boot lidFig. 46 Boot lid
A1
A2
A3
s2dk.1.book Page 49 Wednesday, April 8, 2009 12:23 PM
Page 51 of 294
Unlocking and locking
50
Close large boot lid – Pull the boot lid down and close it with a slight swing
⇒
. The
bonnet locks automatically.
A handle which makes the closing easier is
located on the inner paneling of the
boot lid.
WARNING
•
Ensure that the lock is
properly engaged after clos
ing the boot lid. Other-
wise, the boot lid might open suddenly when
driving even if the boot lid lock
is closed - risk of accident!•
Never drive with the boot lid fully opened or slightly ajar otherwise
exhaust gases may get into the interior of the vehicle - risk of poisoning!
Hinweis
•
After closing the boot lid, it is automatically locked within 2 seconds and
the anti-theft alarm system* is activated.
This applies only if the vehicle was
locked before closing the boot lid.•
The function of the hand grip on the bott
om edge of the boot lid is deactivated
when starting off or as of
a speed of more than 5 km/hou
r. The function of the hand
grip is acitvated again after stopping th
e vehicle and after opening the driver or
front passenger door or after pressing the button on the radio remote control ⇒ page 51.•
Repeated opening and closing of the boot lid can lead to a temporary failure of
the function due to the overheating protection of the motors of the Twindoor system.
Emergency unlocking of the boot lidIf there is a fault in the central locking, you can open the boot lid as follows: – Fold the seat backrest forwards
⇒
page 84.
– Guide the key into the slot in the trim panel as far as the stop
⇒
fig. 47
.
– You can unlock the boot lid by mo
ving in the direction of arrow.
– Open the boot lid/luggage compartment door from outside.Remote controlDescriptionYou can use the remote control:•
to unlock and lock the car,
•
unlock or open the boot lid,
•
Opening and closing window.
A1
Fig. 47 Emergency unlocking of the boot lid
s2dk.1.book Page 50 Wednesday, April 8, 2009 12:23 PM
Page 52 of 294
Unlocking and locking
51
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The transmitter with the battery is housed
in the handle of the remote control key.
The receiver is located in the interior of the car. The operating range of the remote control is approx. 30 m. But this range of the remote control can be reduced if the batteries are weak. The remote control key has a fold-open key
bit which can be used
for unlocking and
locking the car manually and also for starting the engine. If a lost key is replaced or if the rece
iver unit has been repaired or a new unit
installed, it is then necessary for an authorised Škoda Service Partner to initialise the system. Only after this is it possible to again use the remote control.
Note
•
The remote control is automatically deac
tivated when the ignition is switched
on.•
The operation of the remote control may temporarily be affected by interfer-
ence from transmitters close to the car
and which operate in the same frequency
range (e.g. mobile phon
e, TV transmitter).
•
The battery must be replaced, ideally by
an authorised Škoda Service Partner, if
the central locking or anti-theft alarm system does react to the remote control at less than 3 metres away.•
If the driver door is opened, the vehi
cle cannot be locked using the remote
control.
Unlocking and locking carUnlocking the vehicle
– Press button for about 1 second. Locking the vehicle
– Press button for about 1 second.Deactivating safe securing system – Press button twice in 3 seconds. Further information
⇒
page 46.
Small boot lid release
– Press button for about 1 second
⇒
fig. 48
. Further information
⇒
page 48.
Automatic raising of the small boot lid
– Press button for about 2 second
⇒
fig. 48
. Further information
⇒
page 48.
Folding out of the key –Press button .
Fig. 48 Remote control key
A1A3A2A2A2A4
s2dk.1.book Page 51 Wednesday, April 8, 2009 12:23 PM
Page 53 of 294
Unlocking and locking
52
Folding up of the key – Press button and collapse the key bit in the housing.The turn signal lights flash twice as
confirmation that the vehicle has been
unlocked. The vehicle will lock again auto
matically if you unlock the vehicle using
button but do not open a door or the
boot lid within the next 30 seconds. This
function is intended to prevent the car being unlocked unintentionally. In addition, when the car is unlocked, the
power seats and exterior mirrors* move
into the position assigned to this key. The stored setting of driver seat and exterior mirrors is retrieved. When the vehicle is unlocked or locked, the interior lights and the lights of the entry area are automatically switched
on or off via the door contact.
Display of the locking The turn signal lights flash once to co
nfirm that the vehicle has been correctly
locked. If the doors or the boot lid remain open
after the vehicle has been locked, the turn
signal lights do not flash unt
il they have been closed.
WARNING
If the vehicle is locked from the outside and the safe securing system is acti- vated, there must not be any person in the vehicle as it is then not possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into
the vehicle in an emergency - hazard!
Note
•
Operate the radio remote control only wh
en the doors and boot lid are closed
and you have visual contact with the vehicle.•
Once in the car, you must not press the lock button
of the radio remote
control before inserting the key into the ignition lock in order to avoid the car being inadvertently locked and, in addition, th
e anti-theft alarm system* being switched
on. Should this happen, press the unlock button
of the radio remote control.
•
The automatic raising of the small boot
lid can be impaired at temperatures
below +4°C.Synchonisation of the remote controlIf the vehicle cannot be unlocked by actuatin
g the remote control system then it is
possible that the code in the key and the
control unit in the vehicle are no longer
synchronised. This can occur when the buttons on the radio-operated key are actu-ated a number of times outside of the operative range of the equipment or the battery on the remote control was replaced. This means it is necessary to
synchronise the code as follows:
•
Press any button on the remote control.
•
Pressing of the button means that the d
oor will unlock with the key within 1
minute
⇒page 47, “Emergency unlocking and locking of the driver's door”.
Anti-theft alarm system*DescriptionThe anti-theft alarm system increases the level of protection against people seeking to break into the vehicle. The system triggers audible and visual warning signals if an attempt is made to break into the vehicle. How is the alarm system activated? The anti-theft alarm system is activated wh
en the vehicle is locked with the key in
the driver's door or by us
ing the radio remote control
⇒page 47, “Emergency
unlocking and locking of the driver's door
”. The door contact monitoring is acti-
vated approx. 15 seconds after the locking. The interior and the towing protection monitoring are activated appr
ox. 30 seconds after the locking. If a door is opened
during activation, the monitoring is
only activated 5 se
conds after closing.
A4
A1
s2dk.1.book Page 52 Wednesday, April 8, 2009 12:23 PM
Page 54 of 294
Unlocking and locking
53
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
How is the alarm system deactivated? The alarm system is deactivated by pressing the unlock button on the radio remote control. The vehicle is automatically locked again if the vehicle is not opened within 30 seconds after reactivating the anti-theft alarm system. The alarm system is also deactivated if you unlock the vehicle door using the key within 45 seconds after locking the vehicle. Once you unlock the vehicle by inserting the key into the driver door within 45 seconds, you then have to insert the key into the ignition lock and switch the igni- tion on within 15 seconds after unlocking th
e door in order to deactivate the alarm
system. The
alarm will be triggered
if you do
not switch on
the ignition within 15
seconds. When is the alarm triggered? The following security areas of the locked vehicle are monitored:•
Bonnet,
•
Boot lid,
•
Doors,
•
Ignition lock,
•
Socket of the factory-fitted towing device,
•
Angle of the vehicle*,
•
Vehicle interior*,
•
A drop in voltage of the on-board power supply.
An alarm is immediately triggered if either
of the two battery terminals is discon-
nected while the anti-theft alarm system is activated. How is the alarm switched off? You switch the alarm off if you unlock the
car with the radio remote control in the
key or if you switch the ignition on.
Note
•
The working life of the alarm siren is 6 years. More detailed information is avail-
able by a specialist garage.
•
Before leaving the car, check that all the doors, windows and the electric
sliding/tilting roof* are properly closed in order to ensure that the anti-theft alarm system is fully operational.•
Coding of the radio remote control and
the receptor part precludes the use of
the radio remote control from other vehicles.Interior monitor and towing protection monitoring*
The interior monitor detects movements inside the car and then trig- gers the alarm.Switch off the interior monitor and towing protection monitoring – Switch off the ignition. – Open the driver door. – Press the button
at the centre column on the driver side
⇒
fig. 49
,
the symbol
which lights up in the button changes from red to
orange.
– Lock the vehicle within 30 seconds.The interior monitor and the towing protection monitoring are switched on again automatically the next ti
me the car is locked.
Fig. 49 Button for interior monitor and towing protec-tion monitoring
s2dk.1.book Page 53 Wednesday, April 8, 2009 12:23 PM
Page 57 of 294
Unlocking and locking
56
Force limiter of the power windowsThe electrically operated power windows are fitted with a force limiter. It reduces the risk of bruises or injuries when closing the windows. If there is an obstacle, the closing proce
ss is stopped and the window goes down by
several centimeters. If the obstacle prevents the window from
being closed during the next 10 seconds,
the closing process is interrupted once ag
ain and the window go
e s d o w n b y s e v e ra l
centimeters. You must try to close the window once
again within 10 seconds after the window
has gone down twice, even if the obstacle
was not yet removed, the closing process
is stopped. During this time it is not possible to automatically close the window. The force limiter is still switched on. The force limiter is only switched off, if you attempt to close the window within the next 10 seconds -
the window closes now with full strength!
If you wait longer than 10 seconds, th
e force limiter is switched on again.
WARNING
You should take particular care when closing the windows! You may other- wis e su ffe r s ev e re inj uri e s a s a re sul t o f g e t tin g an a rm , fo r e xa m pl e, j am m e d in the window!Window convenience operationYou can open and close the electrically powered windows as follows when unlocking and locking the vehicle (j
ust closing of the sliding roof).
Opening a window•
by holding the pressed unlock button on the remote control,
•
by holding the pressed top part of the
button for the central locking system in
the driver door,
•
by holding the key in the driver's lock in the unlock position
⇒page 47, “Emer-
gency unlocking and lockin
g of the driver's door”.
Closing a window•
by holding the pressed lock button on the remote control,
•
by holding the pressed bottom part of
the button for the central locking system
in the driver door,•
by holding the key in the driver
's lock in the lock position
⇒page 47.
You can interrupt the opening or closing operation of the windows immediately by releasing the key or the lock button.
WARNING
The system is fitted with a force limiter
⇒page 56. If there is an obstacle, the
closing process is stopped and the wi
ndow goes down by several centime-
ters. You should then take particular care when closing the windows! You may otherwise suffer severe injuries as a result of getting an arm, for example, jammed in the window!
Note
The convenience opening of the windows with the aid of the key in the driver's lock is only possible within 45 seconds after deactivating or activating the alarm system.Operational faultsElectrically operated power windows do not operate If the battery has been disconnected an
d then reconnected while the window was
opened, the electrically operated power windows do not operate. The system must be activated. Proceed as follows in
order to re-establish the function:
•
you can close the window
by pulling the respective switch on the top edge
•
release the switch
s2dk.1.book Page 56 Wednesday, April 8, 2009 12:23 PM
Page 59 of 294
Unlocking and locking
58
ClosingSliding closed/closing the sliding/tilting roof – Turn the switch to position
⇒
fig. 52
.
Safety closing The sliding/tilting roof is equipped with an overload protection system. If an obstacle (e.g. ice) prevents closing,
the sliding/tilting roof stops and opens
completely. You can close the sliding/tilting roof completely without overload protection by pressing the
switch to the position
⇒page 57, fig. 52
at the front
for as long as it takes for the sliding/tilting roof to shut completely
⇒
.
WARNING
Close the sliding/tilting roof carefully - risk of injury!Convenience operationYou can also close an open sliding/tilting roof from the outside. – Keep the lock button on the radio remote control pressed or hold the
key in the lock of the driver's do
or in the lock position until the
sliding/tilting roof is closed
⇒
.
The closing operation stops when one releases the key or the lock button.
WARNING
Close the sliding/tilting roof carefully - risk of injury! The overload protec- tion system does not function with the convenience closing.
Electric sliding/tilting roof with solar cells*If there is sufficient bright sunlight, the solar cells on the sliding/tilting roof deliver power for the fresh air blower. Further information
⇒page 109.
The operation of the sliding/tilting roof with solar cells is the same as of a normal sliding/tilting roof.Emergency operationYou can close and/or open the sliding/tilting roof by hand if the system is defect.
AA
AA
Fig. 53 Detail of the head- liner: point for positioning screwdriverFig. 54 Detail of the head-liner: Emergency operation
s2dk.1.book Page 58 Wednesday, April 8, 2009 12:23 PM
Page 60 of 294
Unlocking and locking
59
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Position the flat blade of a screwdriver carefully against the rear edge
of the cover of the electrical drive
⇒
fig. 53
.
– Pull the cover down. – Insert an Allen key, Group 4, up to the stop into the opening and close
and/or open the sliding/tilting roof
⇒
fig. 54
.
– Press on the cover again by first of all inserting the plastic lugs and
then pushing the cover up.
– Have the fault rectified by a specialist workshop.On vehicles fitted with a storage compartment for spectacles*, this compartment must be opened before removing the cover for the emergency operation ⇒ page 98.Note
It is necessary after each emergency operation to move the sliding/tilting roof into the basic position. Here you have to turn th
e control dial forward to the switch posi-
tion
⇒page 57, fig. 52
and press for about 10 seconds.
AA
s2dk.1.book Page 59 Wednesday, April 8, 2009 12:23 PM
Page 61 of 294
Lights and Visibility
60
Lights and VisibilityLightsSwitching lights on and off
Switching on side lights – Turn the light switch into position
.
Switching on the low beam and main beam – Switch on the ignition. – Turn the light switch into position
.
– Press the main beam lever forward in order to switch on the main
beam
⇒
page 67, fig. 61
.
Switching off lights (except daylight driving lights) – Turn the light switch into position°0.When the parking lights are switched on, the symbol
next to the light switch is
illuminated.
Low beam comes on only if the ignition is
switched on. After switching off the igni-
tion, the low beam is switched off automati
cally and only the side lights come on.
On models fitted with
right-hand steering
the position of certain switches differs
from that shown in
⇒fig. 55
. The symbols which mark the switch positions are
identical, however.
WARNING
Never drive with side lights on - risk of accident! The side lights are not bright enough to light up the road sufficiently in front of you or to be seen by other oncoming traffic. In this case, always switch on the low beam when it is dark or if visibility is poor.
Note
•
An audible warning will sound if you withdraw the ignition key and open the
driver's door when the vehicle lights are still on.•
The acoustic warning signal is switched off over the door contact when the
driver's door is closed (ignition off). The
vehicle can be parked with the side lights
on.•
If the car is parked for a lengthy period
, we recommend switching off all lights,
or leaving only the parking lights switched on.•
The switching on of the described lights
should only be undertaken in accord-
ance with the legal requirements.•
If a fault occurs in the light switch, the low beam comes on automatically
•
In the event of cool or humid weather co
nditions, the headligh
ts can be misted
up from inside.
− The temperature difference between interior and external area of the head- light lenses is decisive. − When the driving lights are switched on, the light outlet surfaces are free from mist after a short period. The headli
ght lenses can possib
ly mist up at the
border areas.
Fig. 55 Dash panel: Light switch
s2dk.1.book Page 60 Wednesday, April 8, 2009 12:23 PM