boot SKODA YETI 2009 1.G / 5L User Guide

Lights and Visibility
55
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Rain lights If you switch on the windscreen wipe in th
e operation rain sensor* for longer than 10
seconds or in the operation permanent wipe (position 2 or 3)
⇒page 63 switching on
for longer than 15 seconds, the side lights
and low beam are switched on automati-
cally. The light switches off if the windscreen wipe is in operation rain sensor* for more than 4 minutes or is not switched
on in the operation permanent wipe.
WARNING
The automatic light control only operat
es as a support. Th
e driver is not
released from his responsibility to inspect the light and if necessary to switch on the light depending on the light conditions. The light sensor cannot detect for example rain or snow. For these conditions we recommend to switch on the low beam
!
Note
•
Do not affix any stickers in front of the light sensor, so that you do not impair its
function or put it out of operation.•
The same principles as for using the automa
tic light control also
apply to the light
which is switched on manually
⇒page 53.
Cornering lights*The cornering lights are used to illuminate
the curves by means of the cone of light
swiveling together with the front headlight with Xenon lights*. This function is active when the speed of the car increases to more than 10km/h. The swiveling function of the headlights ca
n be switched off / on via the menu point
Assistant
in the main menu of the Information display*
⇒page 24.
WARNING
If the cornering ligh
ts are defective, the headlights are automatically lowered to
the emergency position, which prevents a
possible dazzling of oncoming traffic.
Thus the illuminated length of the road is shortened. Drive carefully and have the car inspected immediatel
y by a specialist garage.
Coming Home FunctionThe function makes it possible to switch on the lights in the darkness for a short time after leaving the vehicle.Switching on Coming Home Function– The light switch is in the position automatic driving lamp control

and the low
beam illuminates.
– Switch off the ignition. – After opening the driver's door, the function Coming Home is switched on.– Close all the doors and the boot lid and lo
ck the vehicle. After a short time, switch
all lights off.
Depending on equipment fitted the function Coming Home switches on the following lights:•
Parking lights,
•
Low beam,
•
Entry lighting in the exterior mirrors,
•
Licence plate light.
Coming Home Function The lights go out 10 seconds after cl
osing all the doors and the boot lid.
If a door or the boot lid re
mains open, the lights go out
60 seconds after switching off
the ignition. The function Coming Home is controlled with the light sensor in the mount of the inte- rior rear mirror. If the light intensity is higher than the set value of the light sensor, the Coming Home Function is not switched on after switching off the ignition.
Note
•
If the Coming Home Function is switched
on constantly, the battery will be heavily
discharged particularly in short-haul traffic.•
The switching on of the described lights
should only be undertaken in accordance
with the legal requirements.
sgg.6.book Page 55 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
61
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Rear reading lightsSwitching the interior light on– Press the cover glass in the area of the symbol
 ⇒fig. 53
.
Switching the interior light off– Press the cover glass in the area of the symbol
O ⇒fig. 53
.
Door contact setting– Position the cover glass into middle position
.
Front door warning light*The warning light is located in the door trim panel below
⇒fig. 54
.
The warning light goes on every time the do
or is opened. The light goes out about 10
minutes after opening the door in order to
avoid discharging the battery of the vehicle.
There is a reflector installed on some vehicles instead of the warning light.Luggage compartment lightThe lighting comes on automatically when the boot lid is opened. The luggage compartment lighting will switch off again au
tomatically if the boot lid remains open
for more than about 30 minutes.Entry lighting*The lighting is positioned on the bottom edge of the exterior mirror. The light beam is directed towards
the entry area of the front door.
The light comes on after the doors have been
locked or on opening the boot lid. The
light goes out after switching on the ignition
or up to 30 seconds
after closing all the
doors, the bonnet and the boot lid. If a door, the bonnet or the boot lid remains open, the light goes out within 2 minutes if the ignition is switched off.
WARNING
If the entry light comes on, do not touch its cover - risk of burns!
Fig. 53 Detail of the headliner: Rear reading lightsFig. 54 Front door: Warning light
sgg.6.book Page 61 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
78•
Do not place any footmats or other additional floor coverings in the area of
the pedals in order to ensure that all the pedals can be fully depressed and are able to return unobstructed to their initial position - risk of accident!•
There must be no objects on the floor
which could roll under the pedals. You
would then no longer be able to apply
the brakes, operate the clutch or acceler-
ator - risk of accident!Luggage compartmentLoading the luggage compartmentPlease observe the following in the interest of having good handling characteristics of your vehicle: – Distribute the items of luggage as evenly as possible. – Place heavy objects as far forward as possible.– Attach the items of luggage to the lashing eyes or the fixing net*
⇒page 79.
In the event of an accident, there is such a
high kinetic energy wh
ich is produced by
small and light objects that they can cause se
vere injuries. The magnitude of the kinetic
energy depends on the speed at which the vehi
cle is travelling and on the weight of the
object. The speed at which the vehicle is travelling is in this case the more significant factor. Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured object with a weight of 4.5 kg produces an ener
gy, which corresponds to 20 times its own
weight. This means that it results in a weight of approx. 90 kg. You can imagine the inju- ries that can occur, if this “bullet” is fl
ying through the interior
compartment and hits
an occupant.
WARNING
•
Store the objects in the luggage compartment and attach them to the
lashing eyes, e.g. with the fixing nets.
•
Loose objects in the passenger compartment can be thrown forward during
a sudden manoeuvre or in case of an a
ccident and can injure the occupants or
other oncoming traffic. This risk is still increased, if the objects which are flying around are hit by a deployed airbag. In this case, the objects which are thrown back can injure the occupants - hazard.•
Please note that the handling properti
es of your vehicle may be affected
when transporting heavy objects as a result
of the displacement of the centre of
gravity. The speed and style of driv
ing must be adjusted accordingly.
•
The items carried in the luggage compartment should be stowed in such a
way that no objects are able to slip forward if there are any sudden driving or braking manoeuvres undertaken - risk of injury!•
Never drive with the boot lid fully open
ed or slightly ajar otherwise exhaust
gases may get into the interior of the vehicle - risk of poisoning!•
On no account exceed the permissible
axle loads and the permissible gross
weight of the vehicle - risk of accident!•
Never transport occupants in the luggage compartment!Caution
Please ensure that the heating elements of the rear window heater are not damaged as a result of objects sliding in this area.
Note
Tyre pressure must be adjusted to the load
⇒page 215.
WARNING (continued)
WARNING (continued)
sgg.6.book Page 78 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
80 Move the hook into another position– Fold up the hook in direction of arro
w until an angle of 45° is reached
⇒ page 79, fig. 77
.
– Move the hook in direction of arrow into the desired position and fold down the
hook as far as the stop
in direction of arrow
⇒page 79, fig. 77
.
Remove the hook from the fastening strip– Fold the hook in direction of arrow until it slackens.Install the hook on the fastening strip– Position the hook on the fastening strip in
the vertical position in direction of arrow
and lightly press it on.
– Fold the hook down in opposite direct
ion of the arrow until it locks fully.
WARNING
Please refer to the following guidelines
⇒page 78.
Fixing nets - Net programme*Fig. 78 Fixing net: double horizontal pocket
, floor fixing net / double vertical pockets
Fixing examples of the fixing net as do
uble horizontal pocket, floor fixing net
⇒fig. 78

on the left and double vertical pocket
⇒fig. 78
on the right.
The fixing nets* and the installation inst
ruction are located in the luggage compart-
ment.
WARNING
•
The whole strength of the net makes it possible to load the pocket with
objects of up to 3.5 kg in weight. Heavy
objects are not secured sufficiently - risk
of injury and net damage!•
The load to be transported must be fixed in place in such a way that it cannot
move during the journey and when braking.
Caution
Do not place any objects with sharp edge
s in the nets - risk of net damage.
The luggage compartment cover You can use the luggage compartment cover behind the head restraints for storing
light and soft items.
The luggage compartment cover can be remo
ved as required if one must transport
bulky goods.Removing the luggage compartment cover– Fold the seat backrests a little forward in order to facilitate the removal of the
luggage compartment cover.
– Unhook the support straps on the boot lid
⇒fig. 79
.
A1
A2
A3
A4
A5
A4
Fig. 79 Removing the luggage compart- ment coverA1
sgg.6.book Page 80 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
81
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Place the cover in the horizontal position. – Pull the luggage compartment cover out of the holders to the rear or press on
the bottom side of the luggage compartment cover in the front area.
– Fold the slackened front part of the luggage compartment cover over the head
restraints of the rear seats.
– Slightly tilt the luggage compartment cover and remove it to the rear. – Install again by pushing the luggage compartment cover forwards into the holder
and hanging the support straps on the boot lid.
You can stow the removed luggage compartment cover behind the rear seat backrest. The procedure of installing or removing is identical.The luggage compartment cover is foreseen for storage of small objects of up to 2.5 kg. in weight.
WARNING
No objects should be placed on the luggage compartment cover, the vehicle occupants could be endangered if th
ere is sudden braking or the vehicle
collides with something.
Caution
Please ensure that the heating elements of the rear window heater are not damaged as a result of objects placed in this area.
Static separation net*Fig. 80 Use of the static separation net be
hind the rear seats / behind the front seats
Install the static separation net behind the front seats or the rear seats.Installing the static separation net– Remove the luggage compartment cover
⇒page 80.
– Take the separation net out of the bag.– Unfold both parts of the cross rod until they are heard to engage. – Insert the cross rod into the mount first on the one side and push the cross rod
forward. In the same way, fix the cross rod to the other side of the vehicle, mount ⇒fig. 80
.
– Hang the carabines at the ends of the strap into the fixing eyes behind the rear
or front seats.
– Pull the strap through the tensioning clasp,
first of all on the one side and then on
the other side.
Remove the static separation net behind the rear seats– Slacken the bands on both side
s and take off the carabines
⇒fig. 80
.
– Push the cross rod first of all on the one side and then on the other side towards
the rear.
– Take the cross rod out of the mounts .
A2
A2
A1
AB
AB
AC
AC
AB
sgg.6.book Page 81 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
84Removeable storage boxThe storage box is housed under the vari
able loading floor. If
necessary, you can
remove it. There is a space for the vehicle tool kit under the storage box
⇒page 223.
WARNING
The removeable storage box must be lo
cated under the loading floor for the
safe use of the vari
able loading floor.
Roof rackRoof rail
Pay attention to the following points if you
wish to transport luggage or other items on
the roof of your vehicle:•
A special roof luggage rack system was de
veloped for the vehicle, that is why you
should only use a roof luggage rack which has been released for use by Škoda Auto.•
The roof rail is the basis for a complete
roof luggage rack system. Separate addi-
tional holders are required for safety reasons for transporting luggage, bikes, surf-boards, skis and boats.•
The basic version of the roof luggage rack system and further components are
obtainable as accessories from the specialist garages.
Caution
•
Ensure that the opened boot lid do
es not collide with the roof load.
•
On models fitted with a power sliding/tilting roof, ensure that the opened
sliding/tilting roof does not strike any items of luggage transported on the roof.
For the sake of the environment
The increased aerodynamic drag resu
lts in a higher fuel consumption.
Roof loadDistribute weight evenly over the roof lu
ggage rack system. The maximum permissible
roof load (including roof rack system) of
75 kg
and the maximum
permissible total
weight of the vehicle should not be exceeded. You cannot make full use of th
e permissible roof load if
you use a roof luggage rack
system with a lower load carr
ying capacity. The load transported on the roof luggage
rack system must not exceed the weight limit
which is stated in the fitting instructions.
WARNING
•
The items which you transport on the roof bar system must be reliably
attached - risk of accident!•
You must on no account exceed the pe
rmissible roof load, the permissible
axle loads and the permissible gross weight of your vehicle - risk of accident!
Fig. 84 Luggage compartment: Storage box
AA
Fig. 85 Roof rail
sgg.6.book Page 84 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
93
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Removing– Take hold of the flexible storage
compartment at both upper corners.
– Press the upper corners to the inside
and release the storage compartment by
pulling upwards.
– Remove by pulling towards you.Installing– Insert both ends of the flexible storage
compartment into the openings of the right
side trim panel of the luggage compartment and push it downwards until it locks.
Clothes hooksThe clothes hooks are located on the middle
pillar and on the handle of the headliner
above each of the rear doors.
WARNING
•
Ensure that any clothes hanging from the hooks do not impair your vision to
the rear.•
Use the hooks for hanging only light item
s of clothing and ensure that there
are no heavy or sharp-edge
d objects in the pockets.
•
The maximum permissable load of the hooks is 2 kg.
•
Do not use clothes hangers for hanging up items of clothing otherwise this
will interfere with the protection offered by the head airbag*.
Removeable through-loading bag*The removeable through-loading bag
is solely used for transporting
skis.The removeable through-loading bag is foreseen for two pairs of skis. The total weight of the skis which are transported must not exceed 10 kg.Loading– Open a rear side door of the vehicle. – Fold the backrest of the middle seat forwards
⇒page 74.
– Place the empty removeable through-loading bag in the gap between the front and
rear seats in such a way that the end of
the bag with the zip lies in the luggage
compartment.
– Open the boot lid.– Push the skis into the removeable through-loading bag from the luggage compart-
ment
⇒
.
– Close the removeable through-loading bag with the zip.Securing– Pull the securing belt with both lock to
ngues out of the pocket of the removeable
through-loading bag.
– Insert the lock tongues in the belt locks
of the rear middle seat belt , first of
all on the one side and then on the other side
⇒fig. 105
.
Fig. 105 Securing the removeable through-loading bag
AA
AC
sgg.6.book Page 93 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
182
Explanation of technical termsFig. 163 Embankment angle / slope angle Fig. 164 Ground clearance / ramp angleThe technical data
⇒page 245, “Angle (in degree)” refer to ideal conditions. These
values may differ depending on the load an
d composition of the soil and the environ-
ment. The driver is responsible to decide whether a vehicle can overcome a certain situation. Embankment angle (front and rear) Transition from the horizontal plane to an
upward slope or from a downward slope
back to the plane. The angle indication determines the angle at which you can drive the vehicle down the embankment, at a slow speed, without the bumper or the under-body of the vehicle touching the ground. Slope angle The difference of altitude (upward slope) which is overcome on a stretch of road of 100 m, is indicated in percentage or degrees, i.e. the gradiant at which the vehicle can climb
a hill on its own (among other things, depe
nding on the road surface and the engine
power). Ground clearance The distance between the road surface and the deepest point of the vehicle under- body. Ramp angle The angle indication determines the angle
at which you can driv
e the vehicle over a
ramp, at a slow speed, without the underbody of the vehicle touching the ramp edge.
WARNING
When exceeding the maximum value given in the table
⇒page 245, “Angle (in
degree)”, this can result in serious injuries and/or vehicle damage. All of the data was determined on flat, firm and non-slip road surfaces as well as under dry weather conditions. There are no id
eal off-road conditions. Therefore,
never completely go according to th
e maximum values, but always leave a
safety margin.Useful utensilsMany items can be very useful wh
en driving off-road, for example:
•
compass and maps,
•
torch and spare batteries,
•
mobile phone or CB radio,
•
tow bar or tow rope with sufficient tear strength,
•
electrically driven tyre pump for connect
ing to the 12-volt power outlet of the
vehicle,•
a blanket and rubber boots,
•
snow chains,
•
a timber plank which is approximately 4 cm thick and about 1 metre long can be
used as a traction aid when the vehicle is stuck or as a base for the lifting jack,•
additional tools and a folding
yardstick or a measuring tape,
•
spare wheel and tyre repair kit,
AA
AB
AC
AD
sgg.6.book Page 182 Thursday, September 24, 2009 2:32 PM

Taking care of your vehicle and cleaning the vehicle
196
Do not use window leathers which you have us
ed to polish the vehicle body to dry off
the windows. Residues of preservatives in the window leather can dirty the window and reduce visibility. Do not affix any stickers over the inside of
the rear window to avoid damage to the
heating elements of the rear window heater
.
We recommend using a preserva
tive from Škoda genuine accessories offered by your
Škoda dealer.
Caution
Never remove snow or ice from the glass parts with warm or hot water - risk of forma-tion of cracks in the glass!The headlight lensesPlease do not use any aggressi
ve cleaning or chemical so
lvent products for cleaning
the front headlights - risk of
damage to the
plastic lenses.
Please use
soap and clean
warm water.
Caution
Never
wipe the headlights dry and do not use any sharp objects for cleaning the plastic
lenses, this may result in damage to the
protective paintwork and consequently in
formation of cracks on the headlight lenses, e.g. through effect of chemical products.Door and window sealsThe rubber seals on the doors, boot lid,
bonnet and windows remain supple and last
longer if you treat them from time to time with a rubber care product (e.g. with a spray with silicone-free oil). You also avoid premature wear of the seals and prevent leakages in this way. It is also easier to open the doors. Rubber seals which are well cared for also do not stick together in cold winter weather.Locking cylinderWe recommend that you use the spray from Škoda original accessories with regreasing and anticorrosive effect for de-icing locking cylinders.
Note
When washing your vehicle, ensure that as
little water as possible gets into the locking
cylinders.WheelsSteel wheels You should also thoroughly wash the wheels
and wheel trims when giving your vehicle
its regular wash. This prevents any brake dust, dirt and road salt from sticking to the wheel hubs. You can remove stubborn brake
abrasion adhering to the wheels with an
industrial cleaner. Touch up
any damage to the paintwork on the wheels before rust is
able to form. Light alloy wheels Regular care of light alloy wh
eels is necessary in order to retain their decorative
appearance over long periods. It is particul
arly important to remove regularly any road
salt and brake abrasion from light alloy wheels, otherwise the light metal will suffer. Wash thoroughly and then treat the wheels with a protective product for light alloy wheels which does not cont
ain any acidic components. We recommend to apply a
hard wax layer onto the wheel hubs every
three months. You must not use any prod-
ucts which cause abrasion when treating
the wheel hubs. Any damage to the paint
layer on the wheel hubs must
be touched up immediately.
We recommend using a preservative from Šk
oda genuine accessories offered by your
Škoda dealer.
WARNING
One should remember when cleaning th
e wheels that moisture, ice and road
salt may adversely affect braking ef
ficiency - risk of an accident!
Note
Severe layers of dirt on the wheels can also
result in wheel imbalance. This may show
itself in the form of a wheel vibration which
is transmitted to the steering wheel which,
in certain circumstances, can
cause premature wear of the
steering. This means it is
necessary to remove the dirt.
sgg.6.book Page 196 Thursday, September 24, 2009 2:32 PM

Fuses and light bulbs
241
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Removing the bulb for the fog light– Switch the ignition and all lights off. – Remove the rubber protective cap
⇒page 239, fig. 197
.
– Unplug plug . – Take the faulty bulb out of the fixture
by pressing the li
ght socket downwards
and insert a new one.
– Insert the protective cap.Daylight driving lightsRemove the bulb for daylight driving lights– Switch the ignition and all lights off. – Remove the rubber protective cap
⇒page 239, fig. 197
.
– Unplug plug .– Take the faulty bulb out of the fixture by turning in direction of arrow and insert
a new one in the reverse procedure.
– Insert the protective cap.
Rear light unitFig. 203 Removing the rear light unit
/ disconnecting the plug connection
– Open the boot lid. – Unscrew the light with the aid of the Torx
wrench from the vehicle tool kit. The
shorter side of the wrench is used for loosening the screws and the longer side for screwing the screws out completely
⇒fig. 203
.
– Grasp the light at the top and bottom part and pull it slightly to the rear.– Disconnect the plug connection by pressing the catches in direction of arrow
and by pulling them in direction of arrow
⇒fig. 203
.
Changing light bulbs in the rear light unitFig. 204 Remove the middle part
of the light / rear light unit:
Fitting position of the bulbs
AA
A1
A2
Fig. 202 Remove the bulb for daylight driving lights
AA
A1
A2
A1
A2
A3
sgg.6.book Page 241 Thursday, September 24, 2009 2:32 PM