reset SKODA YETI 2009 1.G / 5L Owner's Manual

Instruments and Indicator/Warning Lights
16Instruments and Indicator/Warning LightsGeneral view of the instrument cluster
Engine revolutions counter
⇒page 17
Speedometer
⇒page 17
Button for display mode: − Set hours / minutes − Activating / deactivating the second speed in mph or km/h* − Service interval - Display of the remaining number of days, kilometres or miles to the next Inspection Service / Reset*
1)
Coolant temperature gauge
⇒page 17
Display − with counter for distance driven
⇒page 18
− with Service Interval Display
⇒page 18
− with digital clock
⇒page 20
− with Multi-functional indicator*
⇒page 20
− with Information display*
⇒page 24
Fuel gauge
⇒page 17
Button for: − Reset trip counter for distance driven − Resetting Service Interval Display − Set hours / minutes − Activate / deactivate display mode
Fig. 15 Instrument cluster
1)Valid for countries where the values are indicated in British measuring units.A1A2A3A4A5
A6A7
sgg.6.book Page 16 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
18
Caution
Never run the fuel tank completely empty!
The irregular supply of the fuel system can
lead to irregular running of
the engine. Unburnt fuel may get into the exhaust system
and damage the catalytic converter.
Note
After filling up, it can occur that during dy
namic driving (e.g. numerous curves, braking,
driving downhill and climbing a steep hill) the fuel gauge indicates approx. a fraction less. When stopping or during less dynamic
driving, the correct fuel supply quantity is
indicated. This effect is not a fault.Counter for distance drivenThe distance which you have driven with yo
ur vehicle is shown in kilometres (km). In
some countries the measuring unit “mile” is used. Reset button If you hold the reset button
⇒page 16, fig. 15
pressed for about 1 second, the trip
counter is set back to zero. Trip counter for distance driven The trip counter indicates the distance which you have driven
⇒fig. 16
since this
counter was last reset - in steps of 100 metres or 1/10 of a mile.
Counter for distance driven The counter for distance driven
⇒fig. 16
indicates the total distance in kilometers or
miles which the ve
hicle has driven.
Fa ult di spl ay If there is a fault in the inst
rument cluster, a co
nstant text will appear in the display
Error
. Have the fault rectified as soon as possible by a specialist workshop.WARNING
Never seek to adjust the trip counter for
distance driven while driving for safety
reasons!
Note
If vehicles which are fitted with the info
rmation display* the display of the second
speed is activated in mph or km/h, this driving speed is indicated instead of the counter for the total distance driven.Service Interval DisplayDepending on the equipment installed in the vehicle, the text can differ on the display. Service Interval Display Before the next service interval a key symbol

and the remaining kilometers are
indicated after switching on the ignition
⇒fig. 17
. At the same time, a display appears
regarding the remaining days until the next service interval.
Fig. 16 Display: Co
unter for distance
driven
A7
Fig. 17 Service Interval Display: Note
sgg.6.book Page 18 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
19
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The following will be displayed in the information display*:
Service in ... km or... days
The kilometre indicator or the days indicator reduces in steps of 100 km. or days until the service due date is reached. A flashing key symbol

and the text
Service
appears in the display for 20 seconds
as soon as the due date for the service is reached. The following will be displayed in the information display*:
Service now!
Display regarding the distance and days until the following service interval You can use the button to display the remaining distance driven and the days until the next service interval
⇒page 16.
A key symbol

and a display regarding the remaining kilometers appear for 10
second in the display. At the same time, a display appears regarding the remaining days until the next service interval. On vehicles which are equipped with inform
ation display*, you ca
n call up this infor-
mation in the following menu on
⇒page 24:
„
SETUP (Settings)
„
Service Interval (Service)
„
Info
The following will be displayed in the information display* for 10 seconds:
Service in ... km or... days
Resetting Service Interval Display It is only possible to reset the Service Interval Display, if a service message or at least a pre-warning is shown on the display of the instrument cluster. We recommend having this resetting performed by a specialist garage.The specialist garage:•
resets the memory of the display after the appropriate inspection;
•
makes an entry in the Service schedule;
•
affix the sticker with the entry of the following service interval to the side of the
dash panel on the driver's side. Reset the service interval displays by using the reset button
⇒page 16 on the trip
counter. On vehicles which are equipped
with information display*, you can call up this infor-
mation in the following menu on
⇒page 24:
„
SETTINGS
„
Service Interval (Service)
„
ResetCaution
We recommend that you do not reset the Se
rvice Interval Display yourself otherwise
this can result in the service interval displa
y being incorrectly set, which may also result
in problems with operation of your vehicle.
Note
•
Never reset the display between service intervals otherwise this may result in
incorrect readouts.•
information is retained in the Service Inte
rval Display also after the battery of the
vehicle is disconnected.•
If the instrument cluster is exchanged after a repair, the correct values must be
entered in the counter for the Service Interval
Display. This work is carried out by a
specialist garage.•
The data displayed is the same after resetting the display with flexible service inter-
vals (QG1) using the reset button as that for a vehicle with fixed service intervals (QG2). We therefore recommend having the Service In
terval Display reset
only by an author-
ised Škoda Service Partner who is familiar with the procedure for resetting the display with a vehicle system tester.•
Please refer to the brochure Service schedule for extensive information about the
service intervals.
A3
A7
sgg.6.book Page 19 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
21
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Single-trip memory (memory 1) The single-trip memory collates the driving information from the moment the ignition is switched on until it is switched off. New data will also flow into the calculation of the current driving information if the trip is continued
within 2 hours
after switching off
the ignition. The memory will be is automatically erased, on the other hand, if the trip is interrupted for
more than 2 hours
.
Total-trip memory (memory 2) The total distance driven memory gathers da
ta from any number of individual jour-
neys up to a total of 99 hours and 59 minutes driving or 9.999 kilometres driven. The memory is deleted when either of these limits is reached and the calculation starts from anew. The total-trip memory will not, contrary to
the single-trip memory, be deleted after a
period of interr
uption of driving of 2 hours.
Note
All information in the memory
1 and
2 is erased if the battery of the vehicle is
disconnected.Operating with the buttons on the windshield wiper lever and on the multifunction steering wheel*Fig. 19 Multi-functional indicator: Control elementsThe rocker switch and the button are lo
cated in the grip of the window wiper
lever
⇒fig. 19
on the left. Switching over and resetting is performed with the hand-
wheel
⇒fig. 19
on the multifunction steering wheel.
Selecting the memory– After briefly pressing the button on
the windshield wiper lever or by briefly
pressing the button on the multifuncti
on steering wheel, you can select the
desired memory.
Selecting the functions with the he
lp of the windshield wiper lever
– Press the top or bottom rocker switch
for longer than 0.5 seconds. In this way,
call up in sequence the individual func
tions of the multi-functional indicator.
Selecting the functions with the
help of the multifunction steering
wheel– By pressing the button , you can call up
the menu of the multi-functional indi-
cator.
– Turn the handwheel upwards or downward
s. In this way, call up in sequence
the individual functions of th
e multi-functional indicator.
– Short-term pressing of the button allows to select the highlighted function.Setting function to zero– Select the memory you want.– Press the button or for more than 1 second. The following readouts of the selected memo
ry will be set to zero with the button
on the windshield wiper lever or with the button on the multifunction steering wheel:•
average fuel consumption,
•
distance driven,
•
average speed,
•
Driving time.
You can only operate the multi-functional in
dicator when the igniti
on is switched on.
After the ignition is switched on, the function displayed is the one which you last selected before switching off the ignition.
AA
AB
AD
AB
AD
AA
AC
AD
AD
AB
AD
AB
AD
sgg.6.book Page 21 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
28Language Here you can set in which language the warning and information texts should be displayed. Displays of the MFA Here you can switch off or on certain di
splays of the multi-
functional indicator.
Comfort* You can set the following functions (depen
ding on the equipment installed on the
vehicle):
Lights and Visibility Here you can set how long the light should
stay on for the func
tion Coming/Leaving
Home. Furthermore you can here switch on or
off the function daylight driving lights
and convenience turn signal. After selecting the menu point
Factory setting
the factory setting of the lighting is
established again. Time Here you can set the time, the time format
(12 or 24 hour indicator) and the time
change summer/winter time. Winter tyres Here you can set at which speed a warning signal should sound. This function is used for e.g winter tyres with the permissible maximum speed less than the maximum speed of the vehicle. When exceeding the speed, the following is displayed on the information display*:
Snow tyres max. speed ... km/h (Winter tyres maximum ... km/h)
Measures Here you can set the units for temperat
ure, consumption and distance driven.
Assistant Here you can adjust the tones of the
acoustic signals of the parking aid*.
Second speed Here you can switch on the display of the second speed in mph or in km/h
2).
Tra v e l m o d e Here you can activate / deactivate the mode “tourist light”. This mode makes it possible to drive in countries with opposing traffi
c system, driving on the left/right, without
dazzling the oncoming vehicles. The headligh
t swivel function is deactivated when
switching on this mode. Further information
⇒page 56.
Rain closing
On vehicles with rain sensor you can switch on or off the function for automatic closing of the windows and the sliding/tilting roof in case of ra
in and locked vehicle. If it is
not raining and the function is
set, the windows including
the sliding/tilting roof are closed automatically after approx. 12 hours.
Door open
Here you can switch on or off the functions for opening a single door and automatic closing.
ATA c o n fi r m
Here you can set if a signal to
ne should sound additionally
when activating or deactivating the anti-theft alarm sys- tem.
Window op.
Here you can set the convenience mode only for the driver window or for all the windows.
Mirror down
Here you can switch on or off the function for mirror low-ering on the front passenger side when engaging the reverse gear
a).
Mirror adjust.
Here you can switch on or off the function for left and right exterior mirror adjustment simultaneously.
Fa cto r y se tt ing

After selecting this menu the convenience setting is reset to factory setting. The following is displayed in the infor- mation display: Factory setting for convenience is set
a)This function is only available on vehicles wi
th an electrically adjustable driver seat.
2)Valid for countries where the values ar
e indicated in British measuring units.
sgg.6.book Page 28 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
29
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Service Here you can have the kilometers still to
be driven and the days until the following
service interval shown and the Service Interval Display reset.
Factory Setting After selecting the menu point
Factory Setting
the factory setting of the information
display is established again.
Warning lightsOverview The warning lights indicate certain functions or faults.
Fig. 29 Instrument cluster with warning lights

Turn signal lights (to the left)
⇒page 31

Turn signal lights (to the right)
⇒page 31

Fog lights*
⇒page 31

Main beam light
⇒page 31

Low beam light
⇒page 31

Rear fog light
⇒page 31

Speed regulating system*
⇒page 31
sgg.6.book Page 29 Thursday, September 24, 2009 2:32 PM