key SKODA YETI 2013 1.G / 5L Owner's Guide

OperationFig. 23
Control dial for the sliding/tilting
roof
First read and observe the introductory information and safety warn-
ings on page 44.
Comfort position
›
Turn the switch to position
C
» Fig. 23 .
When the sliding/tilting roof is in the comfort position, the intensity of the wind
noise is reduced.
Open partially
›
Turn the switch to a position in area
D
» Fig. 23 .
Open fully
›
Turn the switch to position
B
» Fig. 23 and hold it in this position (spring-ten-
sioned position).
Tilting roof
›
Turn the switch to position
A
» Fig. 23 .
›
Press the switch in the region
E
towards the roof.
Closing
›
Turn the switch to position
A
» Fig. 23 .
›
Press the switch on the recess
E
down and pull forwards.
Force limiter
The sliding/tilting roof is fitted with a force limiter. The sliding/tilting roof stops and moves back several centimetres when it cannot be closed because there is
something in the way (e.g. ice). The sliding/tilting roof can be fully closed without
a force limiter by pressing the switch on the recess
E
» Fig. 23 down and then
pushing it forward until the sliding/tilting roof is fully closed » .
WARNINGWhen closing the sliding/tilting roof proceed with caution to avoid causing
crushing injuries – risk of injury!
CAUTION
During the winter it may be necessary to remove any ice and snow in the vicinity
of the sliding/tilting roof before opening it to prevent any damage to the opening
mechanism.
Opening/closing the sun screen
Fig. 24
Buttons for sun screen
First read and observe the introductory information and safety warn- ings on page 44.
The sliding sun blind (hereinafter only referred to as a sun screen) can be opened
or closed using the buttons » Fig. 24 .
Explanation of graphic » Fig. 24
Opening
Closing
By pressing the button, the sun blind is fully opened or closed. The movement of the sun blinds can be stopped by briefly pressing any key.
By pressing and holding the button, the sun screen is opened or closed to the de-
sired position. By releasing the button, the opening or closing process is stopped.

45Unlocking and opening

Convenience operation of sliding / tilting roofFirst read and observe the introductory information and safety warn-ings
on page 44.
The sliding / tilting roof can be operated by locking or unlocking using the key or
using the KESSY system with the aid of the sensor
1
» Fig. 14 on page 35.
Closing
›
Press and hold the symbol button  on the key or hold the key in the locking
cylinder of the driver's door in the lock position, or for the KESSY system, keep your finger on the sensor
1
» Fig. 14 on page 35 » .
By releasing the lock or lifting your finger off the sensor
1
when using the KESSY
system, the closing process is immediately interrupted.
Tilting roof
›
Press and hold the symbol button 
on the key.
WARNINGClose the sliding/tilting roof carefully – risk of injury! The force limiter does not
work when convenience closing is in operation.

46Using the system

Switching on the low beam
Switch on the front fog lamp » page 51
Switching on the rear fog light » page 51
Headlight beam control 
Turning the rotary switch B
» Fig. 25 from position  to  gradually activates the
headlight beam control, thereby shortening the beam of light.
The positions of the width of illumination correspond approximately to the fol-
lowing car load.
Front seats occupied, boot empty
All seats occupied, boot empty
All seats occupied, boot loaded
Driver seat occupied, boot loaded
WARNINGAlways adjust the headlight beam to satisfy the following conditions.■The vehicle does not dazzle other road users, especially oncoming vehicles.■
The beam range is sufficient for safe driving.
Note
■ We recommend you adjust the headlight beam when the low beam is switched
on.■
The Bi-Xenon bulbs adapt automatically to the load and driving state of the ve-
hicle when the ignition is switched on and when driving. Vehicles that are equip- ped with Bi-Xenon headlights do not have a manual headlight range adjustment
control.
■
The light switch is in position  or  and the ignition is turned off, the low
beam is switched off automatically and the status light is lit. The side light goes out after the ignition key is removed.

Daylight running lights (DAY LIGHT)
First read and observe the introductory information and safety warn-
ings
on page 47.
The daytime running lights (the only function) provides the lighting of the front
vehicle range.

The daytime running lights are switched on automatically if the following condi-
tions are met:
The light switch A
is in position  or  » Fig. 25 on page 47.
The ignition is switched on.
The parking aid is activated.
Deactivating the function
›
Switch off the ignition.
›
Pull the turning signal and main beam lever towards the steering wheel, push
down and hold in this position.
›
Switch on the ignition.
›
Hold the lever in this position for at least 3 seconds after the ignition is switch-
ed on.
Activating the function
›
Switch off the ignition.
›
Pull the turning signal and main beam lever towards the steering wheel, push it
up and hold it in this position.
›
Switch on the ignition.
›
Hold the lever in this position for at least 3 seconds after the ignition is switch-
ed on.
On vehicles with MAXI DOT display, the function can be enabled or disabled in the menu item Dayl. dri. light » page 29 , Settings .
Note
When the daytime running light is switched on, the side lights (neither at the
front or rear) and the number plate lights are not lit.48Using the system

Parking lightsFirst read and observe the introductory information and safety warn-ings
on page 47.
Parking light  switching on
›
Switching off the ignition.
›
Place the control lever into position
A
or
B
as far as it can go » Fig. 26 on
page 49 - the parking light on the right/left-hand side of the vehicle is switched on.
The parking light  can only be activated if the ignition is switched off.
If the right or left turn signal light has been switched on and the ignition is switched off, the parking light is not automatically switched on.
Switching on the side light on both sides 
›
Turn the light switch
A
to position 
» Fig. 25 on page 47 and lock the vehicle.
After pulling out the ignition key and opening the driver's door, an audible warn-
ing sounds. After a few seconds or after closing the driver's door, the audible
alarm is turned off, but the parking lights will remain switched on.

Instrument lighting
Fig. 30
Controls for the instrument
lighting
First read and observe the introductory information and safety warn-
ings on page 47.
The brightness of the instrument lights can be set only if the parking, low beam or high beam is switched on.
Knob » Fig. 30 .
Adjust brightness of the instrument lighting.
NoteOn vehicles with MAXI DOT display » page 28 the brightness of the instrument
lighting is set automatically. A manual brightness adjustment can therefore only
have a limited effect.
Interior lights
 Introduction
This chapter contains information on the following subjects:
Front interior light
53
Rear interior light
54
Front door warning light
54
Front interior light
Fig. 31
Operation of the front interior light: Version 1/version 2
First read and observe the introductory information given on page 53.
Rocker switch positions » Fig. 31 .
switching on
switching off
Operation using the door contact switch (middle position) 
53Lights and visibility

For vehicles with interior monitoring, there is no icon for the center position (op-
eration with the door contact switch).
Switch for reading lights .
Switching left reading lamp on/off
Switching right reading lamp on/off
If light operation with the door contact switch is enabled, the light will come on
when one of the following events occurs:
› The vehicle is unlocked.
› One of the doors or the luggage compartment lid is being opened.
› The ignition key is removed.
If light operation with the door contact switch is enabled, the light will go off
when one of the following events occurs:
› The vehicle is locked.
› The ignition is switched on.
› About 30 seconds after all the doors have been closed.
Note
If the interior light remains switched on when the ignition is switched off or if one
of the doors is open, the light will automatically go out after around 10 minutes.
Rear interior light
Fig. 32
Interior lights at the rear
First read and observe the introductory information given on page 53.
The light can be operated by moving the lens into one of the following posi-
tions » Fig. 32 .
switch on
switch off
Operation using the door contact switch (middle position) 1)

Front door warning light
Fig. 33
Front door warning light
First read and observe the introductory information given on page 53.
The warning light
» Fig. 33 turns on when the front door is opened.
The warning light » Fig. 33 turns off when the front door is closed.
In vehicles without a warning light only a reflector is installed at this point.
Note
If the door is open and the ignition switched off, the light will extinguish auto-
matically after around 10 minutes.

1)
In this position, apply the same rules to the rear interior light as for the front interior light » page 53,
Front interior light .
54Using the system

Folding-in both of the exterior mirrors using the remote control keyThe entire mirror can be folded by pressing the  symbol button on the remote
control key for 2 seconds. All windows must be closed.
The exterior mirror is folded back into the driving position when the ignition isswitched on.
Automatic dimming mirror
The exterior mirrors are dimmed together with the automatic dimming interior
mirror » page 59 .
Fold in passenger's mirror
On vehicles fitted with the memory function for the driver's seat » page 63, the
mirror tilts down slightly when the reverse gear is engaged and the rotary knob is
in the position 
or in position 
on vehicles with right-hand drive » Fig. 38 . This
provides an aid in seeing the kerb of the pavement when parking the car.
The mirror returns into its initial position after the rotary knob is moved out of po-
sition 
(or position 
on vehicles with right-hand drive) and put into another posi-
tion or if the speed is more than 15 km/h.
This mode can be enabled or disabled via the Maxi DOT display in the Travel
mode » page 29 menu option.
Memory function for mirrors
On vehicles fitted with a memory function for the driver seat, the relevant setting for the exterior mirrors can also be stored automatically when the seat position is
stored » page 63 .WARNINGDo not touch the exterior mirror surfaces, if the exterior mirror heating is
switched on - hazard of burning.
CAUTION
Never mechanically fold in or fold back the exterior mirrors with the fold-in func-
tion  by hand as this will damage the electric drive.
Note
■
The mirror heater only operates when the engine is running and up to an out-
side temperature of +35 ℃.■
If the power setting function fails at any time, the exterior mirrors can be set by
hand by pressing on the edge of the mirror surface.

60Using the system

Seats and useful equipment
Front seats
Introduction
This chapter contains information on the following subjects:
Manually adjusting the front seats
62
Electric front seat adjustment
62
Memory Function of the electrically adjustable seat
63
Memory function of the remote control key
63
The driver's seat should be adjusted in such a way that the pedals can be fully
pressed to the floor with slightly bent legs.
The seat backrest on the driver's seat should be adjusted in such a way that the
upper point of the steering wheel can be easily reached with slightly bent arms.
Correct adjustment of the seats is particularly important for the following: › Reaching the controls safely and quickly.
› A relaxed and fatigue-free body position.
› Achieving the maximum protection offered by the seat belts and the airbag
system.
WARNINGGeneral information■Caution when adjusting the seat! You may suffer injuries or bruises as a re-
sult of adjusting the seat without paying proper attention.■
The electric front seat adjustment is also functional when the ignition is
turned off (even with the ignition key removed). Therefore children should
never be left unattended in the vehicle.
■
The seat backrests must not be tilted too far back when driving, as this will
impair the function of the seat belts and of the airbag system – risk of injury!
■
Never carry more people than there are number of seats in the vehicle.
■
Each occupant must correctly fasten the seat belt belonging to the seat.
Children must be fastened » page 177, Transporting children safely with a
suitable restraint system.
WARNING (Continued)■ The front seats and head restraints must be adjusted to match the body
size at all times and the seat belt must always be fastened properly to provide
the most effective levels of protection to the passengers.■
Do not carry any objects on the front passenger seat except objects de-
signed for this purpose (e.g. child seats) – risk of accident!
WARNINGInformation for the driver■Only adjust the driver's seat when the vehicle is stationary – risk of accident!■
Maintain a distance of at least 25 cm from the steering wheel, and a dis-
tance of at least 10 cm between the legs and the dash panel at the height of
the knee airbag. Not maintaining this minimum distance will mean that the
airbag system will not be able to properly protect you – hazard!
■
Ensure that there are no objects in the driver's footwell, as these may get
caught in the pedal apparatus when driving or braking » page 126. You would
then no longer be able to operate the clutch, brake or acceleration pedals.
WARNINGInformation for the front passenger■Maintain a distance of at least 25 cm to the dash panel. Not maintaining this
minimum distance will mean that the airbag system will not be able to proper-
ly protect you – hazard!■
Always keep your feet in the footwell when the car is being driven – never
place your feet on the instrument panel, out of the window or on the surfaces of the seats. You will be exposed to increased risk of injury if it becomes nec-
essary to apply the brake or in the event of an accident. If an airbag is de-
ployed, you may suffer fatal injuries when adopting an incorrect seated posi- tion!
Note
■ After a certain time, play can develop within the adjustment mechanism of the
backrest angle.■
For safety reasons, it is not possible to store the seat position in the electric
seat memory and remote control key memory if the inclination angle of the seat
backrest is more than 102° in relation to the seat cushion.
■
Each time you store the position of the electrically adjustable driver's seat and
exterior mirrors, the existing setting is deleted.

61Seats and useful equipment

Set the height of the seat cushion›Push the switch A in the direction of one of the arrows 3 » Fig. 40 .
Adjusting the angle of the seat backrest›
Push the switch
B
in the direction of one of the arrows » Fig. 41.
Raising or lowering the curvature of the lumbar support
›
Push the switch
C
in the region of one of the arrows 4 » Fig. 41 .
Reducing or increasing the curvature of the lumbar support
›
Push the switch
C
in the region of one of the arrows 5 » Fig. 41 .
The adjusted driver's seat position can be set in the memory of the
seat » page 63 or the remote control key » page 63.
Note
If the setting procedure is interrupted, you will need to press the button again.
Memory Function of the electrically adjustable seat
Fig. 42
Memory buttons and SET button
First read and observe the introductory information and safety warn-
ings on page 61.
The memory function for the driver's seat provides the option to store the posi-
tions of the driver's seat and the external mirrors. Each of the three memory but-
tons
B
» Fig. 42 can be assigned a set position.
Storing seat and exterior mirror settings for driving forward
›
Switch on the ignition.
›
Adjust the seat to the desired position.
›
Adjust both of the exterior mirrors » page 59.
›
Press the button SET
A

» Fig. 42 .
›Within 10 seconds after pressing the
SET button, press the desired memory
button B.
An acknowledgement sound confirms the storage.
Saving front passenger mirror settings when reversing›
Switch on the ignition.
›
Press the required memory button
B
» Fig. 42 .
›
Adjust the rotary knob for the mirrors to the position  or in right-hand drive to
the position  » page 59 .
›
Engage reverse gear.
›
Adjust the front passenger's mirror to the desired position » page 59.
›
Disengage reverse gear.
The set position of the exterior mirror is stored.
Retrieving the saved setting
The retrieval is possible when turned the ignition is switched on and the vehicle
speed is less than 5 km/h or when the ignition key is inserted in the ignition lock.
›
Press and hold the desired memory button
B
» Fig. 42 for a short while.
Stopping the ongoing adjustment
›
Press any button on the driver's seat.
or
›
Press the button  on the remote control key.
Note
Each time you store the seat and exterior mirror settings for driving forward you
also have to re-store the setting of the exterior mirror on the passenger side for
reversing.
Memory function of the remote control key
First read and observe the introductory information and safety warn-ings
on page 61.
The automatic storage of the driver's seat and exterior mirror positions when
locking the vehicle can be turned on in the memory of the remote control key (af-
terwards only as function of automatic storage).
Storing seat and exterior mirror settings for driving forward
›
Enable automatic storage. 
63Seats and useful equipment

When automatic storage is activated, the current positions of the driver's seat
and the external mirrors are saved in the memory of the remote control key each
time the vehicle is locked. When the vehicle is next unlocked using the same key,
the driver's seat and the external mirrors assume the positions stored in the
memory of this key 1)
.
Saving front passenger mirror settings when reversing›
Unlock the vehicle with the remote control key.
›
Switch on the ignition.
›
Adjust the rotary knob for the mirrors to the position 
or in right-hand drive to
the position  » page 59 .
›
Engage reverse gear.
›
Adjust the front passenger's mirror to the desired position » page 59.
›
Disengage reverse gear.
The adjusted position of the exterior mirror is stored in the remote control key
memory.
Enable automatic storage
›
Unlock the vehicle with the remote control key.
›
Press and hold any memory button
B
» Fig. 42 on page 63. After the seat has
assumed the position stored under this button, at the same time press the but-
ton 
on the remote control key within 10 seconds.
The successful activation of the automatic storage function for each key is con-
firmed by an acoustic signal.
The seat and external mirror positions which are already saved in the memory
button are not saved in the memory of the key.
The seat can be adjusted to the required position if necessary » page 62.
After locking the vehicle, the current positions of the driver's seat and the exter-
nal mirrors are saved in the memory of the remote control key.
Disable the function of automatic storage
›
Unlock the vehicle with the remote control key.
›
Press and hold the SET button
A

» Fig. 42 on page 63. At the same time, press
the button  on the remote control key within 10 seconds.
The successful deactivation of the automatic storage function for each key is con-
firmed by an acoustic signal.
Stopping the ongoing adjustment›Press any button on the driver's seat.
or›
Press the button  on the remote control key.

Front seat functions

Introduction
This chapter contains information on the following subjects:
Front seat heating
64
Front armrest
65
Folding front passenger seat
66
Front seat heating
Fig. 43
Heated front seats
First read and observe the introductory information given on page 64.
Explanation of graphic » Fig. 43
Control the seat heater on the front left seat
Control the seat heater on the front right seat
The seat backrests and seats can be heated electrically. 
1)
The vehicle must be locked and unlocked with the same key to save the seat and exterior mirror po-
sition to the key.
64Using the system

Cigarette lighterFig. 61
Cigarette lighter
First read and observe the introductory information and safety warn-
ings on page 70.
Using the system
›
Press in the button of the cigarette lighter » Fig. 61.
›
Wait until the button pops forward.
›
Remove the cigarette lighter immediately and use.
›
Place the cigarette lighter back into the socket.
WARNING■
Take care when using the cigarette lighter! Improper usage can case burns.■The cigarette lighter also operates when the ignition is switched off or the
ignition key withdrawn. Therefore never leave children unattended in the ve-
hicle.
Note
■ The cigarette lighter socket can also be used as a 12- volt socket for electrical
appliances » page 75, 12-volt power outlet .■
Further information » page 184, Service work, adjustments and technical alter-
ations .

AshtrayFig. 62
Removing/inserting the front
ash tray
Fig. 63
Rear ashtray: low center console / high center console
First read and observe the introductory information and safety warn-
ings
on page 70.
The ashtray can be used for discarding ash, cigarettes, cigars and the like » .
Removing/inserting the front ash tray
›
Pull out the ashtray in the direction of the arrow » Fig. 62.
Insertion takes place in reverse order.
Opening the ashtray on the low centre console
›
Grasp the ashtray cover at the lower edge
A
and fold it open in the direction of
arrow » Fig. 63 .
Remove the ashtray from the low centre console
›
Grasp the ashtray at the handle
B
» Fig. 63 and remove from above. 
74Using the system