bulb SMART FORTWO COUPE 2012 User Guide

The arrow on bulb socket : must be in
line with the line on the headlamp
housing.
X Turn bulb socket : clockwise by a
quarter of turn.
Side turn signal lamp bulb X
Removing: Open the door on the
corresponding side. X
Press on retaining lug : in the
direction of the arrow until the side turn
signal lamp housing disengages.
X Close the door.
X Use a suitable tool to loosen the side turn
signal lamp housing from the fender.
X Turn the bulb socket counterclockwise
and pull it out of the side turn signal
lamp housing.
X Pull the bulb out of the bulb socket.
X Installing: Insert the new bulb into the
bulb socket.
X Insert the bulb socket into the side turn
signal lamp housing and turn the bulb
socket clockwise.
X Fit the side turn signal lamp housing
onto the fender.
X Press gently onto the side turn signal
lamp housing.
The side turn signal lamp housing must
audibly engage. Replacing bulbs for rear lamps
Before
you start to replace a bulb for a rear
lamp, do the following first:
X Turn exterior lamp switch to position
$ (Y page 64).
X Switch off the ignition.
Tail lamp unit X
Removing:
Coupé: Open the upper tailgate.
X Open the lower tailgate.
X Cabriolet: Open the rear soft top
(Y page 74).
X Remove the side cover in the cargo
compartment on the corresponding side.
X Fold the damping material forward, if
necessary. Left bulb carrier illustrated as example
:
Retaining tab
; Electrical connector
X Press retaining tab : in the center of
the bulb carrier upwards.
X Pull the bulb carrier out of the tail lamp
housing.182
Replacing bulbs
>> Practical hints.

Left bulb carrier with bulb sockets (right bulb
carrier in reverse)
:
Retaining tab
= Brake, tail, turn signal and side marker
lamp bulb
? Backup lamp bulb
X Depending on which bulb needs to be
replaced, press gently onto bulb =
or ? and turn it counterclockwise.
X Pull the bulb out of the bulb socket.
X Installing: Insert the new bulb into the
bulb socket.
X Press gently onto the bulb and turn it
clockwise until it engages.
X Insert the bulb carrier into the tail lamp
housing.
X Press gently onto the bulb carrier.
Let retaining tab : engage.
X Fold the damping material backward, if
necessary.
X Reinstall the side cover in the cargo
compartment. High-mounted brake lamp X
Removing: Unscrew retaining screws :.
X Remove high-mounted brake lamp ?.
X Detach electrical connector ;
from bulb
socket =.
X Turn the bulb counterclockwise and pull
it out of its socket.
X Installing: Install in the reverse order.
License plate lamps G
WARNING
High outside temperature, stop-and-go
traffic, driving on long uphill grades, or
driving

at high engine speed may increase
the temperature in the engine
compartment. Therefore the area around the
air slots in the rear apron may be hot. Let
the engine cool off before touching this
area to prevent burns. Replacing bulbs
183
>> Practical hints. Z

X
Use a suitable tool to loosen the
corresponding
license plate lamp unit at
jacking point :.
X Carefully unclip the license plate lamp
unit. X
Detach electrical connectors ;.
X Remove bulb =.
X Insert the new bulb.
X Attach electrical connectors ;.
X Fit the license plate lamp unit on the
right and press gently on the left.
The

license plate lamp unit must audibly
engage. Replacing interior lighting lamps
A 12 V/10 W bulb is required. X
Removing: Use a flat object to pry the
lamp

lens : off from the passenger side. X
Detach electrical connector ; from the
interior lamp.
X Remove bulb = from mount ?.
X Installing: Insert the new bulb.
X Attach electrical connector ; to the
interior lamp.
X Fit the lamp lens on the left in the
opening and press gently on the right.
The lamp lens must audibly engage. Replacing wiper blades
About replacing wiper blades
G
WARNING
For safety reasons, switch off the wipers
and remove the key from the starter switch
before replacing a wiper blade. The
windshield wipers could otherwise be set
in motion and cause injury. G
WARNING
Wiper blades are components that are
subject
to wear and tear. Replace the wiper
blades at least twice a year, preferably in
the spring and fall. Otherwise the windows
will not be properly wiped. As a result, you
may not be able to observe surrounding
traffic conditions and could cause an
accident.
! Hold on to the wiper when folding the
wiper arm back. If released, the force of
the impact from the windshield wiper 184
Replacing wiper blades
>> Practical hints.