brake fluid SSANGYONG KORANDO 1997 Service Owner's Manual

MASTER CYLINDER 4B-3
SSANGYONG MY2002
KAA4B070
COMPONENT LOCATOR
1 Brake Fluid Level Switch Connector
2 Brake Fluid Reservoir
3 Power Booster4 Brake Lines
(Master Cylinder-to-Hydraulic Modulator)
5 Master Cylinder

SSANGYONG MY2002
4B-4 MASTER CYLINDER
ON-VEHICLE SERVICE
BRAKE OIL LEVEL SWITCH
Removal and Installation Procedure
1. Disconnect the brake fluid level switch connector.
2. Disconnect the switch wiring connector.
3. Disconnect the switch from the brake oil tank.
4. Installation should follow the removal procedure
in the reverse order.
REPAIR INSTRUCTIONS
BRAKE FLUID RESERVOIR
Removal and Installation Procedure
Important: Remove the brake fluid reservoir only when
it must be replaced because of damage or leaks.
1. Disconnect the brake fluid level switch connector.
2. Drain the brake fluid.
KAA4B020
KAA4B020
KAA4B050
3. Remove the brake fluid reservoir fromthe master
cylinder body by tilting the reservoir and pulling
it up-ward.

MASTER CYLINDER 4B-5
SSANGYONG MY2002
KAA4B060
4. Remove and discard the brake fluid reservoir seals
from the master cylinder body.
Installation Notice:
Lubricate the new brake fluid reservoir seals with
clean brake fluid.
After the installation, bleed the brake system.
Refer to Section 4F, Antilock Brake System and
Traction Control System.
5. Installation should follow the removal procedure
in the reverse order.
YAD4A340
YAD4A350
YAD4A360
3. Remove the master cylinder.
Retain the master cylinder in the vice and
remove the retainer ring from the master cylinder
using the snap ring plier. 2. Loosen the mounting nut of the master cylinder
and remove the master cylinder from the power
booster.
MASTER CYLINDER
Removal Procedure
1. Disconnect the brake lines from the master
cylinder.
Notice: The brake fluid may damage paintwork, if
spillage onto paintwork, wash with cold water
immediately.

POWER BOOSTER 4C-3
SSANGYONG MY2002
KAA4C080
COMPONENT LOCATOR
1 Brake Fluid Level Switch Connector
2 Brake Fluid Reservoir
3 Power Booster4 Brake Lines
(Master Cylinder-to-Hydraulic Modulator)
5 Master Cylinder

SSANGYONG MY2002
4D-2 FRONT BRAKES
DESCRIPTION AND OPERATION
GENERAL DESCRIPTION
When the brakes are applied, fluid pressure is sent to
each brake caliper. The pressure at the caliper is ex-
erted equally against the caliper piston. The pressure
applied to the piston is transmitted directly to the
inboard brake pad. This forces the pad against the inner
surface of the brake rotor. At the same time, fluid
pressure within the caliper piston bore forces the caliper
to slide inward on its guide pins. This action brings the
outboard pad into contact with the outer surface of the
brake rotor. This pressure on both sides of the brake
rotor causes friction, bringing the vehicle to a stop.
BRAKE CALIPER
The caliper has a single bore and is mounted to the
steering knuckle with two mounting bolts. Hydraulic
pressure, created by applying the brake pedal, is con-
verted by the caliper to a stopping force. This force
acts equally against the piston and the bottom of the
caliper bore to move the piston outward and to slide
the caliper inward, resulting in a clamping action on
the rotor. This clamping action forces the linings against
the rotor, creating friction to stop the vehicle.Important:
•Replace all components included in the repair kits
used to service the caliper.
Lubricate the rubber parts with clean brake fluid to
ease assembly.
Do not use lubricated shop air on brake parts, as
damage to the rubber components may result.
If any hydraulic component is removed or discon-
nected, it may be necessary to bleed all or part of
the brake system. Refer to Section 4F, Antilock
Brake System And Traction Control System.
Replace the pads in axle sets only.
The torque values specified are for dry, unlubricated
fasteners.
Perform the service operations on a clean bench,
free from all oily material.
BRAKE PADS
There are two brake pads mounted to each caliper, one
inboard and one outboard. As front disc brake pad wear,
master cylinder reservoir brake fluid level will drop. Fluid
level should be checked after replacing pads.
BRAKE ROTOR
Each front disc brake rotor is vented to help cool it dur-
ing and after brake applications.

FRONT BRAKES 4D-7
SSANGYONG MY2002
KAA4D060
KAA4D070
CALIPER ASSEMBLY
Removal and Installation Procedure
1. Raise and suitably support the vehicle.
2. Remove the front wheels. Refer to Section 2E,
Tires and Wheels.
3. Remove the brake hose mounting nut and
disconnect the hose. Plug the openings in the
caliper and the brake hose to prevent fluid loss
and contamination.
Installation Notice
Tightening Torque 30 Nm (22 lb-ft)
4. Remove the caliper mounting bolts and then
remove the caliper assembly.
Installation Notice
Tightening Torque 95 Nm (70 lb-ft)
Bleed the caliper. Refer to Section 4A, Hydraulic
Brakes.
Notice: do not move the vehicle until a firm pedal
is obtained or improper braking action will result.
Repeatedly press the brake pedal to bring the
pads in contact with the rotor.
5. Installation should follow the removal procedure
in the reverse order.
SPLASH SHIELD
Removal and Installation Procedure
1. Raise and suitably support the vehicle.
2. Remove the front wheels. Refer to Section 2E,
Tires and Wheels.
3. Remove the hub bearing assembly. Refer to
Section 2C, Front Suspension.
4. Remove the front disc brake rotor. Refer to “Front
Disc Brake Rotor” in this section.
5. Remove the splash shield bolt.
Installation Notice
KAA4D090
Tightening Torque 6 Nm (53 lb-ft)
6. Installation should follow the removal procedure
in the reverse order.

FRONT BRAKES 4D-9
SSANGYONG MY2002
YAD4B280
YAD4B290
3. Fasten the bleeder screw as specified torque.
Installation Notice
Assembly Procedure
1. Installation should follow the removal procedure
in the reverse order.
Notice: Clean all the parts in denatured alcohol or
brake fluid. Dry the parts with unlubricated
compressed air and blow out all the passages in
the housing and the bleeder valve.
Apply the brake fluid on the surface of the piston
and cylinder.
2. Fasten the guide rod bolt as specified torque.
Installation Notice
Tightening Torque7 - 13 Nm
(62 - 115 lb-in)
Tightening Torque22 - 32 Nm
(16 - 24 lb-ft)

SSANGYONG MY2002
4E-12 REAR BRAKES
ON-VEHICLE SERVICE
DISC BRAKE ASSEMBLY
Removal Procedure
1. Remove the rear wheel.
Notice:
Park the vehicle on the flat ground and fix the
vehicle not to move it.
Release the parking brake.
Position the transmission in NEUTRAL.
2. Remove the brake hose from the rear brake
caliper.
Notice: Be carefully to prevent the brake fluid loss
and contamination.
3. Remove the caliper cylinder mounting bolt and
remove the disc pad and the cylinder.
YAD4C130
YAD4C140
RERAIR INSTRUCTIONS
4. Remove the caliper mounting bolt and remove the
caliper assembly.
YAD4C150

REAR BRAKES 4E-17
SSANGYONG MY2002










yyyyyyy yyyyyyy
yyyyyyy
yyyyyyy
yyyyyyy
yyyyyyy
yyyyyyy
yyyyyyy
yyyyyyy
yyyyyyy
yyyyyyy
DRUM BRAKE ASSEMBLY
1. Remove the tires
Notice:
Park the vehicle on the flat ground and fix the
vehicle not to move it.
Position the transmission in NEUTRAL.
2. Disconnect the brake pipe from the rear brake.
Notice: Be carefully to prevent the brake fluid loss
and contamination.
3. Insert the bolt (M8) to the service hole of the brake
drum and remove the brake drum.
4. Remove the service hole plug of the axle shaft.
YAD4C290
YAD4C300
YAD4C310
5. Remove the return spring.
(1) Disconnect the upper return spring.
(2) Disconnect the lower return spring.
(3) Disconnect the lever spring.
(4) Disconnect the adjuster lever from the adjuster.
YAD4C320

SSANGYONG MY2002
4E-22 REAR BRAKES
UNIT REPAIR
WHEEL CYLINDER
Disassembly Procedure
1. Remove the upper brake return spring and remove
the wheel cylinder with pulling the upper lining
outside.
2. Disassembly the wheel cylinder assembly.
Remove the dust boot and do not reuse them
(1).
Remove the piston (2).
Remove the piston cup and do not reuse it (3).
Remove the spring assembly (4).
Remove the bleeder screw (5).
3. Clean all the parts with the denatured alcohol. Dry
the parts with unlubricated compressed air.
Bleeder Screw7 - 10 Nm
(62 - 89 lb-in)
8 - 12 Nm
(71 - 106 lb-in)
Wheel Cylinder
Mounting Bolt
Notice: Lubricate the new seals, the piston, the
piston cup and the wheel cylinder bore with clean
brake fluid before assembly. 4. Installation should follow the removal procedure
in the reverse order.
5. Tighten the bleeder screw and wheel cylinder as
specified torque.
YAD4C460
YAD4C470
YAD4C480