wiper SSANGYONG KORANDO 2012 User Guide

03-158710-01
Power-up reminder wiper ▶
If the intermittent/automatic wiper switch is in "ON" position, the wiper motor does not operate even
when turning the ignition switch to ON from OFF position.
When turning the intermittent/automatic wiper switch to ON from OFF position with IGN ON, the wipers
operate once at low speed initially regardless of the communication with the rain sensor. After that, the
wipers operate once at low speed only when the rain sensor detects
the side fascia panel. 1.
2.

03-16
Washer coupled wiper in rain sensing mode ▶
When the washer switch signal is received during intermittent operation coupled with rain sensor
with IGN ON and intermittent/automatic washer switch operation, the wipers operate in washer
coupled mode regardless of the communication with the rain sensor. However, if the washer switch
signal is received the washer relay is activated and wiper relay remains activated, when the data
coupled with rain sensor indicates continuous wiper operation.
Even though the wiping system is in washer coupled wiper mode, the operating data are sent to rain
sensor. 1.
2.
Sensitivity adjustment (instant wiping) ▶
When the wiping speed control switch is turned to "FAST" with IGN2 ON, intermittent/automatic wiper
switch in "ON" position and wiper motor stop (parking position), the wiper motor operates one cycle at
low speed.
(only when the rain sensor detects raindrops)
If the wiping speed control switch is changed more than 2 stages within 2 seconds, the wiper motor
operates only one cycle. 1.
*

03-178710-01
Processing method for abnormal wiper parking signal ▶
The wiper system sends continuously the signal for current status when the wiper parking terminal is
shorted to ground with IGN2 ON and intermittent wiper switch in "ON" position.
The wiper motor runs only when the rain sensor requires the wiper operation. 1.*
When the parking terminal is shorted to power with IGN2 ON and intermittent wiper switch in "ON"
position, the wiper system sends the signal for current wiping status for 2 seconds. After that, it sends
the current signal for parking status continuously.
The wiper motor runs only when the rain sensor requires the wiper operation. 2.*

03-18
Processing method for rain sensor malfunction ▶
If the BCM is received the signal for sensor malfunction from the rain sensor unit when turning the
wiping speed control switch to 2 from 3 stage with IGN ON and intermittent/automatic wiper switch in
"ON" position, the wiper motor operates one cycle at low speed. 1.
If the BCM is received the signal for communication error from the rain sensor unit when turning the
wiping speed control switch to 3 from 4 stage with IGN ON and intermittent/automatic wiper switch in
"ON" position, the wiper motor operates one cycle at low speed. 2.

03-198710-01
Speed sensitive intermittent wiper ▶
The BCM without rain sensor operates the wiper as follows:
When turning the ignition switch to ON from OFF position with the intermittent wiper switch in "ON"
position, the wipers do not operate.
When turning the wiper switch to ON from OFF position after turning the ignition switch to ON position,
the wipers operate one cycle.
The wiper's operation cycle depends on the vehicle speed (CAN communication with instrument
cluster) and wiping speed the side fascia panel.
<0054004700760097008c00990088009b0090009600950047008a00a0008a0093008c00610047005a00b700570055005c0047009a008c008a0047004f006d0068007a007b00500047009b009600470058006000b700590047009a008c008a0047004f007a00
730076007e0050> 1.
2.
3.

03-20
Wiper low/high control ▶
The wiper low relay is activated when the wiper low switch is operated and the wiper high relay
activated when the wiper high switch is operated.
The wiper motor returns to parking position and stops, even when turning off the ignition switch during
wiper operation.
The wiper relay should remain activated during wiper operation in low/high mode even though the
system does not receive P-POS signal. (During intermittent/automatic wiper operation, the wiper relay
should be deactivated after 5 seconds if there is no P-POS signal for 3 seconds in order to inform the
driver of faulty signal)
While the wiper operates at low/high speed, the front/rear washer switch can be operated but the auto
washer switch cannot.
The wiper motor returns to parking position and stops when turning off the ignition switch during wiper
operation in high mode. 1.
2.
3.
4.
5.

06-22
Hazard warning flasher switch
When this switch is pressed, the hazard
warning flashers blink.
Windshield heated glass switch
This is to prevent the windshield wiper blades
from being frozen.
The heated wire operates for about 12
minutes. Press the switch again to stop the
operation.
The indicator in the switch comes on when in
use.
TRIP/Reset switch
Whenever pressing this button, the
information is displayed in the following order:
Odometer, Trip A, Trip B, Distance to empty,
Average fuel consumption, Instant fuel
consumption, Illumination level, Ambient air
temperature (for STD); Trip A, Trip B,
Distance to empty, Average fuel
consumption, Instant fuel consumption,
Illumination level, Ambient air temperature
(for SVC). Press and hold this button to
initialize (reset) Trip A/Trip B and average fuel
consumption, adjust illumination level or
change the unit of temperature.Rear glass/outside
mirror heated wire switch
Press this switch to turn on the tailgate and
outside rearview mirror heated wire. The
heated wire operates for about 12 minutes.
Press the switch again to stop the operation.
The heated glass will operate for about 6
minutes when the switch is pressed again
within 10 minutes after completion of its first
operation cycle.
The indicator in the switch comes on when in
use.

06-318510-00
Multifunction wiper switches
2) Multifunction Switch
Multifunction light switches
Light switch
Front wiper switch
Wiper speed dial
Rear wiper switch Front fog lamp switch
Front auto washer switch The multifunction switch contains the auto washer and wiper switch, front fog lamp switch and auto
hazard warning flasher switch. For the vehicle with air bag, since the contact coil is fitted to the upper part
of the multifunction switch and ESP steering wheel angle sensor is fitted to upper part of the contact coil,
pay attention to when removing and fitting or checking the wiring.

06-338510-00
The wiper operates for 1 cycle
when pushing up the lever. The
lever will return to the "OFF"
position when released.
Wiping speed control switch
When turning to FAST, wiping speed gets faster and when
turning to SLOW, wiping speed gets slower. Stop the operation.
Wiper speed controls
automatically according to the
vehicle speed or amount of rain
(rain sensing wiper).
Wiping speed gets faster when
placing the pointer at the "HI"
position. Wiping speed gets slower
when placing the
pointer at the "LO" position. MIST
OFF
AUTO
LO
HI Auto washer switch
If pressing the switch when the wiper
switch turns to the "OFF" position,
washer fluid is sprayed once and
wiper operates 4 times.
After a while, washer fluid is sprayed
once more and the wiper operates 3
times. Wiper switch ▶

06-34
Rear wiper switch
When the switch is fully turned, washer fluid will
be sprayed onto the rear window glass and the
wiper will also operate.
When the switch is released, it will stop in the
Rear Wiper Operation mode and only the wiper
will keep operating.
Rear wiper operation
Rear wiper stops
When the switch is fully turned, washer fluid will
be sprayed onto the rear window glass and the
wiper will also operate. When the switch is
released, it will return to the “OFF" position
and turn off the wiper and washer.