relay SSANGYONG KORANDO 2012 Workshop Manual

04-238712-03
(4) Engine stop
When the START button is pressed at the vehicle speed of 3 km/h or less, the SKM turns off the IGN
relay to stop the engine.
When the vehicle speed is 3 km/h or more or no speed signal is input, the SKM performs the
following functions: 1.
2.
When the START switch is pressed for 3 sec. or more at more than 3 km/h, the ignition status is
changed from IGN to ACC.
If the switch is pressed again, the ignition status is changed from ACC to IGN.
When the START switch is pressed for 3 sec. or more with no vehicle speed signal (CAN signal
timeout, abnormal signal), the ignition status is changed from IGN to ACC. If the switch is pressed
again, the ignition status is changed from ACC to OFF. -
-
When the START button is pressed and held with IGN ON, the ignition status is changed to OFF.
When the START button is pressed briefly, the ignition status is changed to ACC ON. 3.
(5) ACC ON/Power OFF
The SKM changes the ignition status to OFF from ACC ON when:
the engine START/STOP button is pressed with the brake pedal released after the ignition status is
changed from IGN ON to ACC ON.
the REKES LOCK or passive LOCK is operated with ACC ON.
the BCM sends the driver's door open signal.
12 minutes have passed with ACC ON. 1.
2.
3.
4.Except brake switch signal input
For the vehicles with A/T, when the START switch is pressed for 10 sec. or more, the ignition
status is changed to IGN ON and the engine start request signal is sent regardless of the brake
signal, provided that the initial ignition status is ACC ON and the gear selector lever is in P or N
position. *-

04-24
6) Power Relay Control
(1) OFF to engine starting
(2) ACC to IGN

06-98510-00
Door lock/unlock switch
When the door lock/unlock switch
is pressed while all doors
including the tailgate are locked,
all doors will be unlocked. When
the switch is pressed again, all
doors will be locked.Window lock switch
If the window lock switch is
pressed down, only driver window
is operative. Passenger and rear
windows cannot be operated by
their switches.
Rear LH window
switch
The window is up and down
while this switch is operated.
Passenger door
switch
The window is up and down
while this switch is operated.
Rear RH window
switch
The window is up and down
while this switch is operated.
Driver door window switch
The driver's door window switch has Auto down/Auto up function. The
window can be controlled within 30 seconds by activating the power
window relay even after turning off the ignition switch.
However, if any of front doors is opened or the Lock switch on the
remote control key is pressed (theft deterrent mode is activated)
during the delaying period, the delaying time is immediately canceled
(power window relay is deactivated).
There are two variants of this: only auto down and anti-trap (auto
down and auto up).

06-10
Time lag power window control ▶
When turning the ignition switch to ON position, the power window relay is turned ON.
The power window relay keeps ON for 30 seconds even when stopping the engine.
However, the power window relay is turned OFF when opening a front door.
When locking the door (activation of theft deterrent mode), the power window relay is immediately
turned OFF. 1.
2.
3.

06-118510-00
Door lock/unlock switch
Function of door lock/unlock switch ▶
There are 5 actuators in door lock/unlock system (including tailgate). All of them can control the
corresponding door lock and unlock separately. But, the driver door lock switch can control all door
locks. The BCM controls the lock/unlock switch using the door lock/unlock relay. This is a same control
type with Auto door lock function that locks the doors when the vehicle speed exceeds 30 km/h. (see
circuit diagram)
Door lock/unlock relay (integrated in BCM) ▶
Door lock/unlock switch
When the door lock/unlock switch is pressed while all doors including the tailgate are locked, all doors
will be unlocked. When the switch is pressed again, all doors will be locked.

06-278510-00
4WD LOCK switch
This switch is of push lock type, which
enables to increase/decrease the
torque to the rear wheels in AWD
mode.
Steering wheel heating switch
This switch is of push return type,
which is used to activate or deactivate
the steering wheel heating function.
ESP OFF switch
The ESP OFF switch is of push return
type, which is used to stop or resume
the ESP function.
4WD LOCK switch
This switch is of push lock type, which
enables to increase/decrease the
torque to the rear wheels in AWD
mode.
HLLD
(Headlamp Leveling Device)
The headlamp aiming can be adjusted
by using this dial-type switch.
Rear fog lamp switch
(EU ONLY)
This switch is of push return type,
which sends ON/OFF signal to the
BCM so that the BCM can switch on
the lamps by activating the rear fog
lamp relay.

06-36
4) Horn Switch
Horn switch
Two horns are installed in the radiator grille at the bottom of both sides (one on each side). There is
another horn installed at the bottom of the battery tray side in the engine compartment for theft alarm.
Operating the horn switch on the steering wheel applies the power to the horn relay to operate both
horns (Dual horn).
The theft deterrent horn is controlled by the BCM in armed mode regardless of the horn relay operation.

06-438510-00
Tailgate open ▶
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
<009a0097008c008c008b00470089008c00930096009e0047005a0047004f00b700570055005800500047009200940056008f00530047009b008f008c0047009b008800900093008e0088009b008c004700960097008c009500470099008c0093008800a000
470090009a0047009b009c00990095008c008b004700760075> for about 1 second, with
power OFF, ACC ON or IGN ON. However, it is turned ON when the vehicle speed is below 3
(±0.1) km/h, with IGN ON.
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h with IGN ON during its operation. However, the BCM does not operate if the tailgate
open switch is pressed when the vehicle speed is above 3 km/h. 1.
2.
<007b008800900093008e0088009b008c004700960097008c0095006100470079006c0072006c007a0047009c009500930096008a00920047004f008b0090009a008800990094008c008b0047008b008c009b008c00990099008c0095009b00470094009600
8b008c0050004702e70047007b008800900093008e0088009b>e open signal → Tailgate
open - Without SKM
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
<009a0097008c008c008b00470089008c00930096009e0047005a0047004f00b700570055005800500047009200940056008f00530047009b008f008c0047009b008800900093008e0088009b008c004700960097008c009500470099008c0093008800a000
470090009a0047009b009c00990095008c008b004700760075> for about 1 second.
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h during its operation.
When the tailgate switch on smart key is pressed in theft deterrent mode or with the smart key
detected by the exterior antenna, the SKM verifies the smart key and disarms the tailgate only. When
the tailgate is open and closed, the system enters into the theft deterrent mode again. If the tailgate
switch is not operated for 30 seconds, the system also does so.
The BCM checks that the verified smart key is in the luggage room 1 second after when the closed
tailgate is detected by the tailgate open switch with power OFF.
If there is a verified smart key in the luggage room when the tailgate is open and closed in theft
deterrent mode, the external buzzer sounds for 5 seconds.
When the driver press the tailgate open switch in order to look for the smart key, the BCM deactivates
lock so that the tailgate can be opened even though the driver door is locked. (maintains standby for
opening without verification) 1.
2.
3.
4. With SKM

07-38310-00
Luminous intensity is a measure for the amount of light which passes through the unit area per
time unit. The SI unit of luminous intensity is the candela (cd), an SI base unit. -Luminous Intensity ▶
Luminance describes the amount of light that passes through or is emitted from a particular area,
and falls within a given solid angle. It is measured in sb or nt. -Luminance ▶
This indicates the amount of light reaching a given area. Measuring unit is lux (lx) and it is not
directly proportional to the brightness of the area as the reflection rate is not included. -Intensity of illumination ▶The LED stands for "Light Emitting Diode" or "Luminescent Diode." LED is a semiconductor diode
that emits incoherent narrow-spectrum light when electrically biased in the forward direction of the
p-n junction, as in the common LED circuit. In short, it is an element that converts electric signals
into light signals. Yellow, blue, red and white LEDs are currently available.
The followings are the advantages of LED.
It is not glaring and doesn't have short circuit unlike the conventional lamps.
It is semi-permanent and doesn't generate heat.
Its power consumption is much lower than those of conventional bulbs. -
- ▶ LED
Pin No. Specification
Operating voltage 9 V to 16 V
Load Max. 200 mA (relay load)
Operating temperature-30℃ to 85℃
Storage temperature-40℃ to ±120℃
Mounting location Top center of inner side of windshield glass
2. AUTOMATIC LIGHT SENSOR SPECIFICATIONS

08-57810-00
1. WIPER AND WASHER SYSTEM
1) AUTO Washer Coupled Wiper Function
If you press the AUTO washer switch briefly with the ignition key ON and INT-AUTO switch "OFF", the
washer motor is operated for about 2 seconds to spray washer fluid once after the switch is turned ON
and the wiper relay is turned ON for 4 cycles. After that, the washer motor is operated for about 2
seconds to spray the washer fluid again and the relay is turned ON for 3 cycles and then the relay is
turned OFF.
2) Rear Washer Fluid Supply System
The front washer fluid reservoir supplies the rear washer fluid without additional washer fluid reservoir. Operating part for rear
wiper/washer
AUTO washer
switch (press)
Washer motor