SSANGYONG KORANDO 2012 Service Manual

03-558710-01
Re-entering into theft deterrent mode after tailgate open 7.
If all the doors, excepting tailgate, are in theft deterrent mode and the BCM is received the signal
indicating that the verified smart key is not in the vehicle when the tailgate is closed again, the
system enters into the theft deterrent mode again in 1 second. At this time, the turn signal lamps
blink twice and exterior buzzer sounds once by the BCM. -
Operation when disarming 8.
The horn and the turn signal lamps stop their operation. -

03-56
16) Time Lag Power Window Control
When turning the ignition switch to ON position, the power window relay is turned ON.
The power window relay keeps ON for 30 seconds even when stopping the engine.
However, the power window relay is turned OFF when opening a front door.
When locking the door (activation of theft deterrent mode), the power window relay is
immediately turned OFF. 1.
2.
3.
17) Sleep Mode
If the driver door/passenger door/rear doors/tailgate lock switch is not changed for 6 seconds with all
driver door/passenger door/rear doors/tailgate closed, key removed, IGN1 and IGN2 OFF, the
vehicle enters into sleep mode for system power down.
If any of conditions in Step (1) is not satisfied, the System Wake-up mode is activated.
When output such as room lamp, key hole illumination, tail lamps and power window is activating or
all the doors keep closed for 30 seconds after door is unlocked for conditions in Step (1), the system
is in normal mode. Then, if there is no change within 6 seconds with all output conditions and ready
conditions released and all the doors closed, the sleep mode is activated.
When turning on the overhead room lamp switch, the overhead room lamps come on for 10 minutes
and go off, and the sleep mode is activated after 6 seconds.
When the coming home light OFF conditions are satisfied, the sleep mode is activated.
In this condition, when opening a door or inserting the ignition key into key hole, the sleep mode is
deactivated. 1.
2.
3.
4.
5.
6.

03-578710-01
18) Flasher (Blinking) Function
Turn signal lamp control ▶
When the BCM is received the multifunction switch signal, it operates the turn signal lamp
and interior buzzer with the intervals of 400 ms ON/400 ms OFF for 75 times/min.
The turn signal lamps are operational only when IGN1 is ON.
If the turn signal lamp is defective during its operation, the turn signal lamp blinks with the intervals of
300 ms ON/300 ms OFF for 100/min and the interior buzzer sounds with same interval.
Defective conditions by BCM: Open - below load of 3.0 A, Short - over load of 7.0 A (load means lamp
load here)
When turning ON the turn signal switch, the lamp blinks 3 times by the BCM. When turning OFF the
switch during the operation, the turn signal lamp blinks 3 times and goes off.
When turning OFF and then immediately ON the turn signal switch during auto blinking operation of 3
times, the turn signal lamp blinks additional 3 times.
When turning ON another turn signal switch during the operation, currently operated turn signal lamp
stops immediately and another turn signal lamp starts blinking. 1.
2.
3.
4.
5.
6.
7.

03-58
Right turn signal lamp control ▶
When the BCM is received the multifunction right turn signal lamp switch signal, it operates the right
turn signal lamp and interior buzzer with the intervals of 400 ms ON/400 ms OFF for 75 times/min.
When turning OFF the right turn signal switch during its operation, the turn signal lamp and buzzer
stop the operation.
The turn signal lamps are operational only when IGN1 is ON.
If the turn signal lamp is defective during its operation, the turn signal lamp blinks with the intervals of
300 ms ON/300 ms OFF for 100/min and the interior buzzer sounds with same interval.
Defective conditions by BCM: Open - below load of 3.0 A, Short - over load of 7.0 A (load means lamp
load here)
When turning ON the turn signal switch, the lamp blinks 3 times by the BCM. When turning OFF the
switch during the operation, the turn signal lamp blinks 3 times and goes off.
When turning OFF and then immediately ON the turn signal switch during auto blinking operation of 3
times, the turn signal lamp blinks additional 3 times.
When turning ON the left turn signal switch during the right turn signal lamp operation, the right turn
signal lamp stops immediately and the left turn signal lamp starts blinking. 1.
2.
3.
4.
5.
6.
7.

03-598710-01
Hazard flasher switch control ▶
When pressing the hazard flasher switch, the left/right turn signal lamps blink with the intervals of 400 ms
ON/400 ms OFF for 75/min and the interior buzzer sounds with same interval.
When pressing the hazard flasher switch again during its operation, the turn signal lamps and horn stop
the operation.
This function is available if the battery is connected (B+).
If the turn signal lamp is defective during its operation, the left turn signal lamp blinks with the interval of
300 ms ON/300 ms OFF (100/min) and the interior buzzer sounds with same interval.
The tolerance between left turn signal lamp and right turn signal lamp should be below 100 ms.
The hazard flasher has a priority over the turn signal lamp.
Priority of hazard flasher is as follows:
Seat belt reminder > Key reminder > Sunroof > Tail lamp > Hazard flasher > Turn signal lamp 1.
2.
3.
4.
5.
6.
7.

03-60
Hazard flasher indicator control ▶
When pressing the hazard flasher switch, the hazard flasher indicator blinks with the interval of
75/min.
When pressing the hazard flasher again switch during Step (1), the indicator stops its operation.
This function is available if the battery is connected (B+). 1.
2.
3.
Auto hazard flasher control ▶
When the auto hazard flasher is operated for 0.1~0.59 seconds, the hazard flasher indicator blinks 3
times.
When the auto hazard flasher is operated for more than 0.6 seconds, the hazard flasher indicator
blinks 10 times.
The hazard flasher has priority over the auto hazard flasher and both have the same flash frequency.
This function is only available when the ignition key is in the "ON" position.
When the ignition switch is turned to OFF position during its operation, the auto hazard flasher stops
the operation.
The hazard flasher stops operation as soon as the signal is received from the turn signal lamp (hazard
flasher) switch during this operation.
If the turn signal lamp switch is turned on, the auto hazard flasher does not operate even though its
signal is received. 1.
2.
3.
4.
5.
6.
7.

03-618710-01
Emergency hazard flasher control (coupled with ABS) ▶
System layout 1.
Operating conditions: When receiving the emergency hazard flasher ON signal from ESP and ABS.
When receiving the emergency stop signal through PCAN communication it blinks with the interval of
4 Hz and when receiving the emergency stop OFF signal through PCAN communication it blinks with
the interval of 1.25 Hz, normal operating speed.
However, the manual operation of the switch has a priority over this function. 2.
Priority
Manual hazard flasher > Emergency stop signal > Emergency auto hazard flasher > Auto hazard
flasher
(If emergency stop signal is received through PCAN communication during hazard flasher
operation, the signal is overridden. If the emergency hazard flasher signal is received during multi-
function automatic hazard flasher operation or multi-function automatic hazard flasher is received
during emergency hazard flasher operation, emergency stop is performed.)
When the emergency stop signal is received, the hazard flasher blinks with the interval of 4 Hz,
then returns to normal operation speed. After that, if the emergency stop signal is received again,
the emergency hazard flasher blinks with the interval of 4 times/sec. -
-

03-62
The emergency hazard flasher does not operate if the vehicle speed is over 50 km/h when the
emergency stop signal is received.
The emergency hazard flasher operates if the vehicle speed is 50 km/h or lower when the
emergency stop signal is received.
When vehicle speed increases more than 10 km/h above the speed when the signal is received
during operation by emergency braking signal, the emergency hazard flasher stops operation.
When turning emergency hazard flasher switch OFF during operation by emergency braking
signal, it stops operation.
It is deactivated automatically 10 seconds after if items 2) and 3) above are not met during
operation by emergency braking signal.
If multi-function automatic hazard flasher signal is received during operation by emergency
braking signal, it will be overridden. 1)
2)
3)
4)
5)
6) OFF conditions:
The BCM flashes the emergency auto hazard flasher with interval of 1.25 times/sec.: 3.

03-638710-01
19) DRL (Daytime Running Light) Control
When receiving the DRL activation signal, the tail lamps are turned ON when turning the ignition
switch to ON position, and the headlamps are turned ON when the engine speed is 300 rpm or
higher.
When turning ON the tail lamp switch during engine running, the headlamps are turned OFF.
The headlamps do not come ON when the engine speed is above 300 rpm with the tail lamp switch
ON.
The auto light sensor is not available in the vehicle with DRL system.
If there is no DRL activation signal, the light system operates in normal conditions. 1.
2.
3.
4.
5.
20) Fog Lamp Control
When pressing the rear fog lamp switch with IGN2 ON (headlamp ON condition), the rear fog lamps
are turned ON. When pressing the rear fog lamp switch again during the operation, the rear fog lamps
are turned OFF.
The rear fog lamps do not come ON when the IGN2 switch is turned to OFF position or the light
switch is OFF.
The rear fog lamps should not automatically come on again if they have been turned OFF by any
other way other than the switch. 1.
2.
3.
(The rear fog lamps are applied to only EU region)

03-64
21) Auto Light Control (LIN)
The BCM communicates with the auto light sensor when turning the ignition switch to ON position, and
controls the tail lamps and the headlamps depending on the LIN data with the light switch AUTO. 1.