ignition SSANGYONG KORANDO 2012 Manual Online

03-54
Disarming 3.
If the door unlock signal is received from the smart key remote control with power OFF or the
outside door handle switch signal is received with the driver door locked, the doors are unlocked,
turn signal lamps blink once, exterior buzzer sounds twice at the intervals with 50 ms ON/450 ms
OFF and theft deterrent mode is deactivated. When receiving the door unlock signal with the theft
deterrent mode disarmed, the turn signal lamps blink and exterior buzzer sounds.
When tailgate is open by tailgate open switch signal (only tailgate disarmed)
When verified smart key is detected and manual tailgate is open by tailgate open switch signal
(only tailgate disarmed)
When ignition switch is turned to ON position -
-
-
-
In theft deterrent mode
BCM observes the conditions below continuously: 4.
Battery connection (B+)
Front/rear door open
Tailgate open
4 doors lock/unlock
Engine hood open -
-
-
-
-
Activation of theft deterrent alarm 5.
When any of doors, tailgate or engine hood is open in theft deterrent mode
When unlocking the door lock switch in theft deterrent mode
When opening a door after completion of theft deterrent alarm (for 30 seconds)
Horn and the turn signal lamps operate for 30 seconds with the interval of 0.5s ON/0.5s OFF. -
-
-
-
Warning cancellation requirements 6.
The theft deterrent alarm is deactivated by the following BCAN signals during its operation: (theft
deterrent mode maintains) -
When door is unlocked by smart key remote control
When door is locked by smart key remote control
When tailgate is open by smart key remote control
When passive door is unlocked due to smart key detection
When tailgate is open due to smart key detection
When panic alarm is activated by smart key remote control 1)
2)
3)
4)
5)
6)
When turning the ignition switch to ON position during the theft deterrent alarm, the alarm stops
immediately.
When turning the ignition switch to ON position during the theft deterrent alarm, the alarm stops and
the theft deterrent mode is deactivated after 30 seconds (remaining time).
If there is not any disarming commend, the alarm stays ON for 30 seconds and the theft deterrent
mode continues. -
-
-

03-56
16) Time Lag Power Window Control
When turning the ignition switch to ON position, the power window relay is turned ON.
The power window relay keeps ON for 30 seconds even when stopping the engine.
However, the power window relay is turned OFF when opening a front door.
When locking the door (activation of theft deterrent mode), the power window relay is
immediately turned OFF. 1.
2.
3.
17) Sleep Mode
If the driver door/passenger door/rear doors/tailgate lock switch is not changed for 6 seconds with all
driver door/passenger door/rear doors/tailgate closed, key removed, IGN1 and IGN2 OFF, the
vehicle enters into sleep mode for system power down.
If any of conditions in Step (1) is not satisfied, the System Wake-up mode is activated.
When output such as room lamp, key hole illumination, tail lamps and power window is activating or
all the doors keep closed for 30 seconds after door is unlocked for conditions in Step (1), the system
is in normal mode. Then, if there is no change within 6 seconds with all output conditions and ready
conditions released and all the doors closed, the sleep mode is activated.
When turning on the overhead room lamp switch, the overhead room lamps come on for 10 minutes
and go off, and the sleep mode is activated after 6 seconds.
When the coming home light OFF conditions are satisfied, the sleep mode is activated.
In this condition, when opening a door or inserting the ignition key into key hole, the sleep mode is
deactivated. 1.
2.
3.
4.
5.
6.

03-60
Hazard flasher indicator control ▶
When pressing the hazard flasher switch, the hazard flasher indicator blinks with the interval of
75/min.
When pressing the hazard flasher again switch during Step (1), the indicator stops its operation.
This function is available if the battery is connected (B+). 1.
2.
3.
Auto hazard flasher control ▶
When the auto hazard flasher is operated for 0.1~0.59 seconds, the hazard flasher indicator blinks 3
times.
When the auto hazard flasher is operated for more than 0.6 seconds, the hazard flasher indicator
blinks 10 times.
The hazard flasher has priority over the auto hazard flasher and both have the same flash frequency.
This function is only available when the ignition key is in the "ON" position.
When the ignition switch is turned to OFF position during its operation, the auto hazard flasher stops
the operation.
The hazard flasher stops operation as soon as the signal is received from the turn signal lamp (hazard
flasher) switch during this operation.
If the turn signal lamp switch is turned on, the auto hazard flasher does not operate even though its
signal is received. 1.
2.
3.
4.
5.
6.
7.

03-638710-01
19) DRL (Daytime Running Light) Control
When receiving the DRL activation signal, the tail lamps are turned ON when turning the ignition
switch to ON position, and the headlamps are turned ON when the engine speed is 300 rpm or
higher.
When turning ON the tail lamp switch during engine running, the headlamps are turned OFF.
The headlamps do not come ON when the engine speed is above 300 rpm with the tail lamp switch
ON.
The auto light sensor is not available in the vehicle with DRL system.
If there is no DRL activation signal, the light system operates in normal conditions. 1.
2.
3.
4.
5.
20) Fog Lamp Control
When pressing the rear fog lamp switch with IGN2 ON (headlamp ON condition), the rear fog lamps
are turned ON. When pressing the rear fog lamp switch again during the operation, the rear fog lamps
are turned OFF.
The rear fog lamps do not come ON when the IGN2 switch is turned to OFF position or the light
switch is OFF.
The rear fog lamps should not automatically come on again if they have been turned OFF by any
other way other than the switch. 1.
2.
3.
(The rear fog lamps are applied to only EU region)

03-64
21) Auto Light Control (LIN)
The BCM communicates with the auto light sensor when turning the ignition switch to ON position, and
controls the tail lamps and the headlamps depending on the LIN data with the light switch AUTO. 1.

03-658710-01
22) Outside Mirror Folding/Unfolding Control
Folding/unfolding control ▶
When pressing the mirror folding/unfolding switch with IGN ON, the mirrors are folded or unfolded
according to the mirror condition. If the outside rearview mirror was folded, the mirror should be
<009c0095008d00960093008b008c008b0053004700880095008b0047009d0090008a008c0047009d008c0099009a008800550047006d00960093008b00900095008e0056009c0095008d00960093008b00900095008e00470096009c009b0097009c009b00
470090009a00470088008a009b0090009d0088009b008c008b> for 16±6 seconds.
This operation time should be completed even when the ignition switch is turned to OFF position
during its operation.
At first time pressing the mirror folding/unfolding switch after reconnecting the battery, the mirror
folding operation is performed.
You can control the mirror position within the first 30 sec. after turning the ignition OFF. In other
words, this control must be available for 30 seconds (time lag period) after turning the ignition switch
to OFF position. Folding/unfolding is completed when time lag of 30 seconds elapse during
operation.
When receiving the folding/unfolding signal during the mirror folding/unfolding operation, the output
should be activated after having time lag of 0.1 second.
The folding/unfolding operation is performed regardless of the vehicle speed.
Manual operation
<005400470074009000990099009600990047009c0095008d00960093008b008c008b004702e700470074009000990099009600990047008d00960093008b00900095008e0056009c0095008d00960093008b00900095008e0047009a0090008e0095008800
930047008d0099009600940047009a009e0090009b008a008f> → Mirror folding
<005400470074009000990099009600990047008d00960093008b008c008b004702e700470074009000990099009600990047008d00960093008b00900095008e0056009c0095008d00960093008b00900095008e0047009a0090008e009500880093004700
8d0099009600940047009a009e0090009b008a008f004702e7> Mirror unfolding 1.
2.
3.
4.
5.

03-66
Auto folding/unfolding control ▶
Setting 1.
Set auto folding function: When pressing the mirror folding switch for over 3 seconds, the auto
folding function is set and the internal buzzer sounds once (ON: 0.1 sec, OFF: 0.2 sec).
Release auto folding function: When pressing the mirror folding switch for over 3 seconds, the
auto folding function is set and the internal buzzer sounds twice (ON: 0.1 sec, OFF: 0.2 sec). -
-
Auto folding sequence 2.
When receiving the LOCK signal from the REKES, the system operates in the sequence of "Door
<00930096008a0092004702e70047007b008f008c008d009b0047008b008c009b008c00990099008c0095009b004700940096008b008c00470088008a009b0090009d0088009b009000960095004702e700470074009000990099009600990047008d009600
93008b00900095008e00490047008d0096009900470069006a>M without SKM.
When receiving the outside door handle switch signal or door lock signal from the smart key
<0099008c00940096009b008c0047008a00960095009b00990096009300530047009b008f008c0047009a00a0009a009b008c0094004700960097008c00990088009b008c009a0047009000950047009b008f008c0047009a008c0098009c008c0095008a00
8c00470096008d0047006b009600960099004700930096008a>k → Theft deterrent mode
activation → Mirror folding" for BCM with SKM. -
-
When the auto folding function is set, the automatic unfolding is not available if the mirrors have been
folded manually.
(The outside rearview mirror will be folded automatically if the auto folding function is set.)
The factory setting is the enabling the auto folding function. 4.
5.
23) Approach (Puddle) Lamp Control
Without SKM ▶
Approach lamp ON 1.
When receiving the UNLOCK signal in the theft deterrent mode, the approach lamps come
ON for 30 seconds.
When turning the ignition switch to OFF from ON position and opening the driver door, the
approach lamps come ON. -
-
Approach lamp OFF 2.
When receiving the door lock signal with the approach lamps ON, the lamps go OFF
(reactivation of theft deterrent mode).
When turning the ignition switch to ON position with the approach lamps ON, the lamps go OFF.
The approach lamps go OFF after 30 seconds. -
-
- Auto unfolding sequence 3.
When receiving the UNLOCK signal from the REKES, the system operates in the sequence of
<0049006b0096009600990047009c009500930096008a0092004702e70047007b008f008c008d009b0047008b008c009b008c00990099008c0095009b004700940096008b008c0047008b008c0088008a009b0090009d0088009b009000960095004702e700
470074009000990099009600990047009c0095008d00960093>ding" for BCM without
SKM.
When receiving the outside door handle switch signal or door unlock signal from the smart key
<0099008c00940096009b008c0047008a00960095009b00990096009300530047009b008f008c0047009a00a0009a009b008c0094004700960097008c00990088009b008c009a0047009000950047009b008f008c0047009a008c0098009c008c0095008a00
8c00470096008d0047006b0096009600990047009c00950093>ock → Theft deterrent
<00940096008b008c0047008b008c0088008a009b0090009d0088009b009000960095004702e700470074009000990099009600990047009c0095008d00960093008b00900095008e00490047008d0096009900470069006a00740047009e0090009b008f00
47007a007200740055> -
-

03-678710-01
24) Buzzer Control
Priority are as follows:With SKM ▶
Approach lamp ON 1.
When turning the ignition switch to OFF from ON position and opening the driver door, the
approach lamps come ON.
When receiving the UNLOCK signal from the smart key remote control or outside door handle
switch signal in the theft deterrent mode, the approach lamps come ON for 30 seconds.
When receiving the AUTO approach signal in the theft deterrent mode, the approach lamps
come ON for 30 seconds. -
-
-
Approach lamp OFF 2.
When receiving the door lock signal from the smart key remote control or outside door handle
switch signal with the approach lamps ON, the lamps go OFF (reactivation of theft deterrent
mode).
When turning the ignition switch to ON position with the approach lamps ON, the lamps go OFF.
The approach lamps go OFF after 30 seconds. -
-
-

03-68
2. IMMOBILIZER/REMOTE CONTROL KEY CODING
1) System Overview
While the communication between BCM/SKM and ECU is based on the CAN communication, the
communication between transponder and BCM/SKM is based on LF (Low frequency) and RF (Radio
frequency). When the ignition switch is turned to ON position, the BCM checks the verified transponder
according to the immobilizer verification procedure, if correct, allows the vehicle to start the engine. The
immobilizer indicator comes on during the communication and if the verification is carried out
successfully the indicator goes off.
If there is something wrong in the system, the indicator blinks.
2) System Layout

03-698710-01
3) Operation of Immobilizer
When the ignition switch is turned to the ON position with REKES key, the BCM checks the crypto code
of the inserted key using the immobilizer antenna and sends whether the engine is startable or not to the
engine ECU through the CAN communication so that the engine can be started.
BCM
REKES key
Immobilizer antenna
ECUCAN line
For the vehicle with the immobilizer, there can be a problem in starting the vehicle or the system error:
When two or more immobilizer keys come into contact with (each) other(s).
When the key is close to any device sending or receiving electromagnetic fields or waves other
than Ssangyong products.
When the key is close to any electronic or electric devices such as lighting equipment, security keys
or security cards.
When the key is close to a magnetic or metal object or a battery. -
-
-
-