lock SSANGYONG KORANDO 2013 Service Manual

How to operate 4WD LOCK switch
When the switch is pressed, 4WD LOCK mode is activated (4WD LOCK indicator lamp comes on). If
you press the switch again, the system enters 4WD AUTO mode (indicator lamp goes off).
4WD AUTO mode (normal)
4WD LOCK switch
(1) 4WD LOCK switch
This provides a slip control for the rear wheels depending on the driving conditions such as stationary,
straight-line motion or cornering motion.
4WD LOCK mode (4WD LOCK switch pressed)
In 4WD LOCK mode, the 4WD LOCK control works in the same way as the AUTO mode, but it
increases the driving force to the rear wheels more than in AUTO mode.
If the rear wheel speed is over 40 km/h, the vehicle enters into the 4WD AUTO mode automatically. If
it is below 35 km/h, the vehicle returns to the 4WD LOCK mode. -
-
4WD mode operation table
4WD LOCK switch Vehicle speed Drive mode
Deactivated (4WD AUTO) Unlimited 4WD AUTO
Activated (4WD LOCK) 40 km/h or higher 4WD AUTO
Activated (4WD LOCK) Below 35 km/h 4WD LOCK
4WD: 4WD stands for Four Wheel Drive and drives all the wheels to maximize the vehicle's driving
force on the unpaved road, rough road, steep hills, sandy or muddy road for enhanced driving
performance.
Electric AWD (All Wheel Drive): 4-wheel drive is an electric drive system in which the vehicle is
usually driving in 2WD mode but, if the vehicle determines that 4WD is needed because of the
differences in slip and cornering between front and rear wheels, road gradient and etc., it is switched
to 4WD automatically by the E-coupling control unit.

8510-00
Door coupled room lamp operation and dimming control
When opening any of doors while the room lamp switch in overhead console is pressed in ("Door"
coupled position), the front and center room lamps come on. If the key is removed and door stays open,
the room lamps automatically goes off after 10 minutes. The sleep mode will be deactivated when the
door is locked or closed with the lamp OFF automatically.
When closing the door with IGN ON, the room lamps go off immediately.
When closing the door with IGN OFF, the room lamps stay on for 2 seconds more and are dimmed
out the side fascia panel.
When turning the ignition switch to ON position during dimming out operation, the room lamps go off
immediately.
When receiving the door unlock signal with IGN OFF, key removed and door closed, the overhead
console room lamp/center room lamp come on for 30 seconds.
For specification with the SKM, the lamps come on by the REKES unlock or passive unlock
signal.
When receiving the door unlock signal again while the lamps stay on by the REKES or passive
unlock signal, the overhead console/center room lamps stays on for 30 seconds more. (the lamps
stay on when receiving door unlock signal)
When opening a door during the coupled operation and dimming operation, the room lamps stays
ON. When closing it again, the lamps stay on for 2 seconds more and are dimmed out for 3 seconds.
While the room lamps dim out when the driver/passenger/rear doors are open and closed, they go off
immediately when entering into the theft deterrent mode.
The room lamps come on when AUTO approach signal is received. 1.
2.
3.
4.
5.
6.
7.
8.

Tailgate open
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
power OFF, ACC ON or IGN ON. However, it is turned ON when the vehicle speed is below 3
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h with IGN ON during its operation. However, the BCM does not operate if the tailgate
open switch is pressed when the vehicle speed is above 3 km/h. 1.
2.
open - Without SKM
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h during its operation.
When the tailgate switch on smart key is pressed in theft deterrent mode or with the smart key
detected by the exterior antenna, the SKM verifies the smart key and disarms the tailgate only. When
the tailgate is open and closed, the system enters into the theft deterrent mode again. If the tailgate
switch is not operated for 30 seconds, the system also does so.
The BCM checks that the verified smart key is in the luggage room 1 second after when the closed
tailgate is detected by the tailgate open switch with power OFF.
If there is a verified smart key in the luggage room when the tailgate is open and closed in theft
deterrent mode, the external buzzer sounds for 5 seconds.
When the driver press the tailgate open switch in order to look for the smart key, the BCM deactivates
lock so that the tailgate can be opened even though the driver door is locked. (maintains standby for
opening without verification) 1.
2.
3.
4. With SKM

8310-00
Approach (puddle) lamp
(10) Puddle (approach) lamp
Approach lamp ON 1.Lamp control for models with SKM
When turning the ignition switch to OFF from ON position and opening the driver door, the
approach lamps come ON.
When receiving the UNLOCK signal from the smart key remote control or outside door handle
switch signal in the theft deterrent mode, the approach lamps come ON for 30 seconds.
When receiving the AUTO approach signal in the theft deterrent mode, the approach lamps come
ON for 30 seconds. -
-
-
Approach lamp OFF 2.
When receiving the door lock signal from the smart key remote control or outside door handle
switch signal with the approach lamps ON, the lamps go OFF (reactivation of theft deterrent
mode).
When turning the ignition switch to ON position with the approach lamps ON, the lamps go OFF.
The approach lamps go OFF after 30 seconds. -
-
- Approach lamp ON 1.Lamp control for models without SKM
When receiving the UNLOCK signal in the theft deterrent mode, the approach lamps come ON for
30 seconds.
When turning the ignition switch to OFF from ON position and opening the driver door, the
approach lamps come ON. -
-
Approach lamp OFF 2.
When receiving the door lock signal with the approach lamps ON, the lamps go OFF (reactivation
of theft deterrent mode).
When turning the ignition switch to ON position with the approach lamps ON, the lamps go OFF.
The approach lamps go OFF after 30 seconds. -
-
-

Front room lamp
2) Operation
Door coupled operation switch: Comes on
when opening door and goes off when closing
with switch pressed
Driver spot lamp switch: Driver front room
lamp comes on when pressing switch
Passenger spot lamp switch: Passenger front
room lamp comes on when pressing switch A.
B.
C.
Center room lamp
Press switch to turn on center room lamp and
press again to turn off it.
It comes on when opening the door with door
coupled operation switch in the front room lamp
pressed even though the switch is in "OFF"
position.
(1) Front room lamp/Center room lamp
Operating the front room lamp and center room lamp switches illuminates the driver/passenger side
lamps and center room lamp.
Room lamp control by door coupled room lamp operation
If a door except the tailgate is opened after the ignition is turned off, provided that door coupled front
room lamp switch is pressed, the front room lamp and center room lamp are illuminated for 2 sec.
and then fade out for 3 sec.
If a door except the tailgate is opened and then closed while the room lamp is fading out, the room
lamp is illuminated for 2 sec. and then fades out for 3 sec. If the ignition is turned on, the room lamp
goes off immediately.
The front room lamp and center room lamp are illuminated for 30 sec. when the door is unlocked by
the REKES or passive door UNLOCK function with IGN OFF and the ignition key removed. If the
REKES or passive door UNLOCK signal is received again, the room lamps are illuminated for
another 30 sec.
The room lamp goes off immediately when the REKES or passive door LOCK signal is received or
the ignition switch is turned to ON position.
If the room lamp is turned on after the ignition key is removed (door open or room lamp switch is
pressed), it is turned off after 10 minutes by the BCM.
When the door open state is changed or the ignition is turned on after the room lamp has been turned
off automatically, the battery saver feature is reset. 1.
2.
3.
4.
5.

3. OPERATING PROCESS
1) Block Diagram
When PAS receives "R" signal, it starts to detect the obstacles behind vehicle after self diagnosis.
If the system detects the obstacle, the buzzer sounds according to the distance. If there is no obstacle, starts
to detect the obstacles after self diagnosis again.

LCD display digital clock
LCD resolution
- LCD display resolution increased
Audio head unit
- Audio head unit design changed
3. MAJOR CHANGES
Audio head unit
Digital clock

RadioCD/MP3
2) Display Window
Radio station band: FM1/FM2/AM
FM stereo reception display
EQ: POP/ROCK/COUNTRY/VOICE/JAZZ/
CLASSIC
Receiving broadcasting frequency
Digital clock
Specified station number: P1~P6 1.
2.
3.
4.
5.
6.Disc insertion display
Play mode display
RDM (Random): Play folder in random
order RPT (Repeat): Play folder
repeatedly INT (Intro): Play folder intro
Current folder name
Play disc
Current playing song name
Other information of current playing song:
Play time/album/artist/genre 7.
8.
9.
10.
11.
12.
USB
USB connection
USB play 13.
14.
BT AUDIO
Bluetooth connection 15.

Turn the power off and set the displayed current time and date.
When pressing the SET button, "Setup List" is displayed.
- "Setup List" screen is displayed only for 5 seconds.
Turn the [TUNE] dial to select a desired "Time & Date" and press the [ENTER] button.
Turn the [TUNE] dial to select a desired setup item and press the [ENTER] button.
Clock On/Off
Turn the [TUNE] dial or press the [ENTER] button to select the desired setting value. Repeat these
steps if several items need to be set. (e.g. YY/MMDD in date setting)
- Set Time: Set the current time.
- Set Time Format: Set the time format to 12-hour or 24-hour system.
- Set Date: Set the date.
- Display Digital Clock On/Off: Set whether the digital clock is displayed or not. 1.
2.
3.

4.
6. CURRENT TIME/DATE SETTING

A/T assembly
Automatic transmission is available as 4WD- and 2WD-type,
and provides 6 speeds for forward travel and 1 reverse
travel. It is also equipped with the torque converter with inner
lock-up clutch and electronically controlled solenoid which
controls all hydraulic functions.
3. CHASSIS COMPONENT LAYOUT
PTU (Power Transfer Unit)
The PTU is a device that transfers the power
generated from the engine to the rear axle through
propeller shaft and E-coupling by changing the power
4WD vehicle.Rear axle assembly
The rear axle installed in this car is a removable
axle, called IRDA (Independent Rear Differential
Axle). The rear differential carrier is installed
directly on the sub frame, and there is an
independent suspension that allows each wheel
on the same axle to move vertically independentl
y
of each other with the universal joint and the slip
joint.
E-coupling control unit (E-Coupling ECU)
The E-coupling unit is a control unit which determines
the magnetic force by considering CAN signals (wheel
speed, engine torque, pedal opening, ABS/ESP CAN
signals, etc.) from other ECUs.
Inhibitor switch
Torque converter Oil pan
E-coupling sideRear axle side
Propeller shaft
1) 4WD Vehicle With Automatic Transmission
GSLDSLInhibitor switch
Torque converter Oil pan