turn signal SSANGYONG KORANDO 2013 Repair Manual

8010-01
Operations for power supply in SVC
When the ignition switch is turned to ON position, the message "WELCOME" is displayed for 2
seconds on the DOT LCD and the seat belt reminder comes on for 4 seconds. However, if a signal
with higher priority is received, the seat belt reminder comes on only for 2 seconds
to display it.
The pre-warning (system check) indicator comes on for 4 seconds and goes off 0.4 seconds after
that the ignition is switched on.
All input signals can be input 4 seconds after the pre-warning (system check) indicator starts
illuminating.
Only the symbol and DOT LCD are illuminated initially, if the SKM (Smart Key Module) or door (B-
CAN) signal is received
while B+ power is supplied.
If the ignition is switched on with the LCD illuminated, the DOT LCD and the symbol follow
the side fascia panel.
When the step 1, 2 and 3 are performed after 4 seconds, the seat belt warning lamp is deactivated
in advance.
Dial light ON condition: Lights up gradually for 2 seconds when the ignition is switched on. 1.
2.
3.
4.
5.
6.
4) Illumination & Brightness
(1) Operations for Power Supply

8010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch to
ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

8010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch
to ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

Timeout processing time for buzzer interval after measuring distance/self diagnosis: 600 ms
- If timeout is reached, the PAS returns to undetected condition.
Process while re-inputting
After timeout, the process is performed normally if the signal required for display is received from
beginning to end.
(not detectable if the signal is received in the midst of process) 1.
2.Exception/error handling -Buzzer interval when measuring distance

8010-01
Pin No. Message Operating condition
Domestic Export
Tire alignment
(applies to
vehicle with
EPS)
CAN scan(This message goes off when all the CAN signal inputs
are normal)
ESCLLCD display shows this message when ESCL (Electric
Steering Column Lock) system is defective. There is
no specific ESCL warning light on the instrument
cluster.
This problem could be temporary. Turn the ignition off
and then on again to check if this message will be
disappeared.
This message helps the driver to predict the driving
direction since the tire alignment is displayed on the
instrument cluster.
The images on the left show that the tires are
aligned to the left. When the tires are aligned to the
right, the image is symmetrical vertically.
Tire alignment is displayed between level 0 and
level 5 depending on the alignment degree when
the ignition switch is turned to "ON" position from
"OFF" position with the shift lever in "P" or "N"
position. While the images up to level 2 comes on
for 5 seconds, the images from level 3 stay on.
These messages are not displayed when the EPS
check message is displayed. -
-
-
-
Pin No. Message Operating condition

8010-01
2) What Is Shown On Instrument Cluster
Supervision type
Standard type
(1) Self diagnosis for gauge
Speedometer/tachometer (RPM): Oscillates between lower mark and upper mark repeatedly. -
(2) Self diagnosis for warning lamp and indicator lamp
All the warning lamps and indicator lamps come on by MICOM control (CAN communication) and
they blink if faulty.
(However, the wired type symbols such as air bag, LH/RH turn signal indicators, hazard warning
flasher, high beam, front fog lamp do not come on.) -
(3) Miscellaneous
When entering into the self diagnosis mode, the instrument cluster illumination output will be 100%.
All the segments are ON. -
-

8510-00
1. SPECIFICATIONS
Unit Specification
Multifunction
switchRated voltage DC 12 V
Rated
loadMultifunction
turn light
switchLight switch ON: 1 A (relay load)
Dimmer & passing
switchHigh beam: 0.3 A (relay load)
Low beam: 0.3 A (relay load)
Passing: 0.3 A (relay load)
Turn signal lamp
switch0.1 A (relay load)
AUTO hazard
warning flasher
switch0.1 A (relay load)
Multifunction
wiper
switchWiper switchLO: 0.1 A (relay load)
HI: 0.1 A (relay load)
Fixed: Max. 0.1 A (relay load)
AUTO washer switch
0.1 A (relay load)
Washer switch 0.1 A (relay load)
Wiping speed control
switchMax. 25 mA
Mist switch 0.1 A (relay load)
Rear wiper & washer
switchRear wiper: 0.1 A (relay load)
Multifunction switch

8510-00
Door lock/unlock control by central door lock switch
When pressing the central door lock/unlock switch, BCM sends the LOCK or UNLOCK signal
according to the previous condition of driver door lock switch for 0.5 seconds.
The central door dock switch is not available when the system is in theft deterrent mode.
When turning the ignition off, all doors are automatically unlocked if any of the door lock (knob)
switches is in LOCK position.
When pressing the central door lock switch with any door open, the system unlocks the doors
immediately after locking them. 1.
2.
3.
4.

8510-00
Windshield heating switch
Press this switch to operate the windshield
heating system for 12 minutes. Press the
switch again to stop the system. The
heated glass will operate for about 6
minutes when the switch is pressed again
within 10 minutes after completion of its
first operation cycle. The indicator lamp for
the switch comes on when the heating is
on.
Hazard warning flasher switch
When the driver presses the switch, all the
turn signal lamps flash regardless of the
ignition switch status. Pressing the switch
again turns off the turn signal lamps. The turn
signal lamp does not operate while the
hazard warning flasher operates.
TRIP/RESET switch
Whenever pressing this button, the information is
displayed in the following order: Odometer, Trip
A, Trip B, Distance to empty, Average fuel
economy, Instant fuel economy, Illumination level,
Tire pressure (with TPMS), Ambient air
temperature (for STD); Trip A, Trip B, Distance to
empty, Average fuel economy/Instant fuel
economy, Illumination level, Tire pressure (with
TPMS), Ambient air temperature (for SVC). Press
and hold this button to initialize (reset) Trip A/Trip
B and average fuel consumption, adjust
illumination level or change the unit of
temperature.
Description
Rear glass/outside rearview mirror heating
switch
Press this switch to operate the rear glass and
outside rearview mirror heating system for 12
minutes. Press the switch again to stop the
system. The heated glass will operate for about 6
minutes when the switch is pressed again within
10 minutes after completion of its first operation
cycle. The indicator lamp for the switch comes on
when the heating is on.
The switch is operable only when the engine
is started.
The hazard warning flasher blinks
during emergency hazard warning
lamp control and air bag deployment
signal activation.
The switch is operable only when the
engine is started.

8510-00
Operation process
When the driver presses the switch, all the turn signal lamps flash regardless of the ignition switch status.
Pressing the switch again turns off the turn signal lamps. The turn signal lamp does not operate while the
hazard warning flasher operates.
Hazard warning flasher switch
(4) Hazard warning flasher switch
The hazard warning flasher blinks during emergency hazard warning lamp control and air bag
deployment signal activation.