Back seat SSANGYONG KORANDO 2013 Service Manual

0000-00
(2) CAN communication flow chart
Splice pack Wiring harness Location
S101 W/H Floor(LH) Glow Control Unit
S102 W/H Floor(RH) Inside RH Fender
S202 Main wiring Backside Cluster(LH Cowl Cross Member)
S204 Main wiring Backside Cluster(Upper ICM Relay Box)
S205 W/H Main Backside Audio(CTR Cowl Cross Member)
S206 W/H Floor(LH) Under Driver Seat
S401 W/H Floor(LH) Beside PAS Unit(Inside LH QTR Trim)

0000-00
2) CAN Communication Wiring Diagram
Splice pack Wiring Location
S101 W/H Floor (LH) Glow Control Unit
S102 W/H Floor (RH) Inside RH Fender
S202 W/H Main Backside Cluster (LH Cowl Cross Member)
S204 W/H Main Backside Cluster (Under ICM Relay Box)
S205 W/H Main Backside Audio (CTR Cowl Cross Member)
S206 W/H Floor (LH) Under Driver Seat
S401 W/H Floor (LH) Beside PAS Unit (inside LH QTR Trim)

Power seat switch
(1) Power seat switch (Driver side)
4) Power Seat Switch Assembly
Seat sliding
Seatback reclining
Seat height adjustment A.
B.
C.
Seat sliding Seatback reclining Seat height adjustment
Power seat switch

8510-00
Front seat heating and ventilation switch (2-
level of driver seat heating and ventilation, 2-
level of passenger seat heating)
A. Driver seat heating switch
B. Driver seat ventilation switch
C. Passenger seat heating switch
5. SEAT HEATING AND VENTILATION SWITCH
1) Front Seat Heating and Ventilation Switch Overview (2-level of
Driver Seat Heating and Ventilation, 2-level of Passenger Seat
Heating)
The temperature of the seat can be adjusted in 3
seat heated wire and ventilation switch. Every
time the seat heating and ventilation switch is
pressed, the temperature level goes down by
one level. Pressing the switch a third time will turn
off the operation. Pressing the desired side of the
switch heats the seat cushion and seatback or
activates the seat ventilation function. The
temperature of the seat is kept uniform by cutting
off or connecting power through thermistor fitted
in the seat. The seat heating and ventilation unit
controls the rpm of the motor using PWM control
to operate the seat ventilation.
Front seat heating & ventilation switch (2-level of driver seat heating and ventilation, 2-level of
passenger seat heating)-
-
The front seat heating and ventilation functions cannot be operated at the same time.
The front seat heating and ventilation switch functions only when the engine is started. -
-Seat heating and ventilation unit & switch application

Front seat heating switch
A. Driver seat heating switch
B. Passenger seat heating switch
Rear seat heating switch
A. Rear LH seat heating switch A. Rear RH seat heating switch
The front seat heating switch can be operated to
the desired temperature (LO/HI) by pressing the
the seat heating switch to heat the seat and
seatback. When the temperature reaches 40
connects and cuts the power to keep the
temperature stable. There is no separate seat
warmer unit to control the temperature of the seat
heating system.
2) Front Seat & Rear Seat Heating Switch Overview
LH RH
The front seat and rear seat heating switches operates with IGN ON.
The seat heating and ventilation unit is not fitted in a vehicle without seat ventilation function. -
-

3. CAUTIONS FOR AIR BAG SYSTEM
Cautions for air bag maintenance
Whenever installing or removing the devices related to the air bag system, disconnect the negative
battery cable and wait for at least 30 seconds.
Do not connect a tester probe to the inflator to measure the resistance of the component of the air
bag system. The detonator of the inflator may explode due to a sudden extra power supplied by the
tester.
Note that the used components related to the air bag system, especially the air bag unit, should be
packed in an air tight container and prevent it from any impact or damage.
When there is any deployed air bag (including curtain air bag and seat belt pretensioner), the entire
system including the air bag unit should be replaced. The deployed air bag unit should not be reused
since it has status data when it is deployed, and the data cannot be cleared with a diagnostic device.
The air bag and seat belt pretensioner systems contain explosive charges, so handle carefully when
disposing or replacing them. 1.
2.
3.
4.
5.
Cautions for air bag maintenance
Do not modify, change or apply impact on any air bag component. The air bag may be deployed
abruptly, causing serious injuries.
Children and infants should ride in a rear seat. Seating in the passenger seat with carrying a
child or infant is strictly prohibited. An infant or a child could be severely injured by the air bag
deployment.
A child restraint system must not be installed on the front seat. An infant or a child could be severely
injured by the air bag deployment when it is fitted to the passenger seat.
Do not place any objects on the air bag inflation location. You may get injured by those objects during
deployment.
Never put your arms around the front seat from behind, lean on the front seatback, or put your arms
out of the window. You can severely injured when the side air bag deploys.
Never lean on the door since it becomes very dangerous when the side air bag deploys.
The side air bag deploys when there is a severe side collision.
Do not slam the front door to close it. The side air bag may deploy unexpectedly.
When an occupant fastens the seat belt in an unstable or inclined posture, the air bag system cannot
protect the occupant properly. Moreover, the occupant can be injured by the air bag.
Do not move your seat too close to the steering wheel or dashboard. Being too close to the
steering wheel or instrument panel during the air bag deployment could cause serious injury,
including death
Hold only the outer rim of the steering so that the air bag can inflate without any hindrance.
Do not incline toward the steering wheel. Never allow the passenger to put hands or feet on the dash
board. The air bag cannot work properly Do not hold and operate the steering wheel by crossing your
arms You could get seriously injured when the air bag deploys. 1.
2.
3.
4.
5.
6.

7.
8.
9.
10.
11.

2) Seat Heated Wire and Ventilation Unit
Item Specifications
Seat heated
wire and
ventilation unitRated voltage DC 12 V
Operating voltage DC 9 V to 16 V
Operating temperature
Rated loadHeated wire
(driver & passenger
seats)
Ventilation
(driver seat)DC 12 V - max. 0.9 A
Cut off over-
currentHeated wire
(driver & passenger
seats)
Ventilation
(driver seat)
Ventilation
motorOperating currentLevel 1
Level 2
Ventilation motor
revolutions
(rpm)Seat
cushionLevel 1 Level 2
Seat
backLevel 1
Level 2

7410-00
2. WARNINGS FOR POWER SEAT
Adjust the driver seat before driving.
Make sure that the seat is firmly secured after adjusting.
Never drive the vehicle with the head restraint removed or lowered excessively. Otherwise, you
r
neck, spine or other parts of the body can be severely injured in the event of an accident.
If you recline the seatback excessively, you could slide under the seat belt and be injured severely
in a collision.
Do not put any object that could damage the seat on the seat.
The front and rear seats are equipped with the heated wire (seat warmer) system. Using the seat
warmer system excessively may cause minor burns. The following occupants should exercise
special care when using the heated wire seat.
Infants, children, old or handicapped persons
Persons with sensitive skin
Exhausted persons
Persons who is drunk or took medicine which causes drowsiness such as sleeping pills, cold
tablets, etc. -
-
-
-
Do not place anything on the seat that insulates against the heat, such as a blanket or cushion.
Make sure that the head restraints are in place and secured properly. Never drive the vehicle with
the head restraint removed.
To minimize the injuries in a collision or an abrupt stop, make sure the seatback is in the upright
position before driving. If the seatback is reclined too much, the occupant could slide under the seat
belt in a collision or an abrupt stop and cannot be protected properly by the air bag system.
3. CAUTIONS FOR POWER SEAT
You can operate the power seat with the ignition switch OFF. However, frequent operation of the
seat switch with the engine stopped can result in battery becoming discharged.
Operating more than one seat adjustment switch at the same time can cause damage to the seat
motor. Therefore, operate the seat switch only one at a time.
Do not use organic solvents such as benzene, thinner, alcohol or gasoline to prevent the seat cove
r
from being damaged while cleaning.
Do not operate the seat position adjustment switch forcefully when the seat does not move or it
contacts an object.
If the power seat is not operated, check and correct the problem before driving off.

Front seat heated wire and ventilation unit
The front seat heated wire and ventilation unit has been added.
- Driver seat (heated wire and ventilation), passenger seat (heated wire)
- The heated wire and ventilation unit is not applied to a vehicle with heated wire only.
Mounting location for
ventilation motor
4. MAJOR CHANGES
Front seat heated wire and ventilation unit
Heated wire and ventilation
unit
mounting location
Seatback
Seat cushion
Seat heated wire and ventilation unit & switch application

Front seat heated wire and ventilation switch
Heated wire Heated wire and
ventilation
Front seat belt (3-point type)Front seat and seat switch
1. SEAT/SEAT BELT OVERVIEW
The seat is divided into front seat (driver & passenger) and rear seat.
The front seat has the heated wire in the seat cushion and seatback and the rear seat has it in the seat
cushion. The ventilation function is only applied to the driver seat. The seat belts of all seats are 3-point
type.
2. SEAT/SEAT BELT LAYOUT
Driver seat heated
wire switch
Passenger seat
heated wire switchDriver seat heated
wire switch
Driver seat
ventilation
switchPassenger
seat heated
wire switch