clutch SSANGYONG MUSSO 1998 Workshop Repair Manual

TRANSFER CASE (TOD) 5D2-45
19 Clutch Pack Assembly
22 Snap Ring
23 Wave Washer
24 Apply Cam
14. Remove the chain, driven sprocket and drive sprocket
as an assembly.
15. Remove thrust washer from output shaft.
16. Remove the magnet from the slot in the front of the case
bottom. Remove the output shaft and oil pump as an
assembly.
Notice
If there is removal resistance, do not pound or use force
to disassemble the pump.
17. If required, to remove the pump from the output shaft,
rotate the pump to align.
18. Pull out the shift rail.
18 Drive Sprocket
58 Drive Chain
59 Driven Sprocket
12 Rear Output Shaft
16 Oil Pump
61 Magnet
19. Remove the helical cam from the front case. If required,
remove the helical cam, torsion spring and sleeve from
the shaft.
20. Remove the high-low range shift fork and collar as an
assembly.
21. Expand the tangs of the large snap ring in the case. With
the input shaft against a bench, push the case down and
slide the main drive gear bearing retainer off the bearing.
Lift the input shaft and front planet from the case.
22. If required, remove the oil seal from the case by prying
and pulling on the curved-up lip of the oil seal. Do not
damage the bearing, bearing cage or case.

TRANSFER CASE (TOD) 5D2-49
12. Install the output shaft and oil pump in the input shaft.
Make sure that the internal splines of the ouput shaft
engage the internal splines of the high-low shift collar. Make
sure that the oil pump retainer arm and oil filter leg are in
the groove and slot of the front case.
13. Install the magnet in the slot in the front case just above
the oil filter leg.
14. Install the front output shaft in the front case.
15. Install the thrust washer on the rear output shaft. Install
the chain, drive sprocket and driven sprocket as an
assembly over the output shaft.
Notice
lThe driven sprocket (on the front output shaft) must
be installed with the marking REAR facing toward the
rear case, if so marked.
lDrive sprocket has a bushing pressed into it.
16. Install tone wheel onto the front output shaft. Make sure
the spline on the tone wheel engages the spline on the
front output shaft.
17. Install clutch pack assembly onto the rear output shaft.
Make sure the spline of the clutch pack engages to the
spline of the sprocket.
18. Install snap ring onto the rear output shaft. Start the snap
ring over the spline and use the wave spring to seat the
snap ring in the snap ring groove. If the snap ring will not
install, the thrust washer inside the clutch pack may not
be seated properly.
1 2 Rear Output Shaft
1 6 Oil Pump6 1 Magnet 1 2 Rear Output Shaft
1 3 Oil Strainer
1 6 Oil Pump
16a Pump Retainer

5D2-50 TRANSFER CASE (TOD)
19. Install wave spring, insulator washer and armature. (Three
offset slots must align with housing to be installed)
Notice
Three slots on the thrust washer must be aligned with the
three tabs on the clutch pack housing.
20. Install apply cam onto the rear output shaft, install three
balls into the apply cam, install cam and coil housing
assembly onto rear output shaft. Install thrust bearing
assembly onto output shaft.
21. If removed, drive the front output shaft ball bearing into
the rear cover bore with Front Shaft Needle Bearing
Replacer and Driver Handle.
22. If removed, install the rear output bearing in the rear case
bore. Drive the bearing into the rear case bore with Output
Shaft Bearing Replacer and Driver Handle. Make sure that
the bearing is not cocked in the bore. Install the internal
snap ring that retains the bearing to the rear case.
23. Install the clutch coil from inside the rear case until the
wire and studs extend through the cover. Install the washers
and nuts and tighten.
CAUTION
Do not kink or trap the wire while seating the clutch coil to
the case.
24. Slide the spring spacer on the camshaft and position it
beneath the drive tang. Place the torsion spring on the
camshaft. Position the first spring tang to the left of the
camshaft drive tang(View A). Wind the second spring tang
clockwise past the drive tang(View B). Push the torsion
spring and sleeve in as far as it will go (View C). This will
seat the second spring tang on the right side of the drive
tang. Install the helical cam and slide the drive tang between
the torsion spring tangs as far as it will go.

5D2-52 TRANSFER CASE (TOD)
32. Install shift shaft oil seal if it is not installed.
33. Using pliers equipped with soft jaws, rotate the triangular
shaft so it is aligned with the triangular slot in the transfer
case shift motor. If triangular shaft will not rotate, rotate
the rear output shaft.
34. Slightly loosen the two nuts that attach the slotted support
bracket to the end of the motor house.
35. Apply Black Non-Acid Cure Silicone Rubber or equivalent
to motor housing base and install on transfer case.
36. Install the transfer case shift motor and three bolts along
with speed sensor wire harness bracket and tighten.
Notice
The wire harness must be routed as shown to provide
clearance and to prevent the wire harness from grounding
the damper.
37. Holding the slotted support bracket tight against the motor
housing end, secure the bracket to the transfer case,
tightening the bolt with lockwasher to 8-11 Nm (72-96 lb-
in).
38. Retighten the two nuts that attach the slotted support
bracket to the end of the motor.
39. Install the clutch coil wire terminal and sensor wires.

7B/C-2 MANUAL & SEMIAUTO-HVAC
Application
Type
Capacity
Condenser Fan Motor OutputDescription
Parallel type (Multi Flow Condenser)
11,000 kcal/h
160W
CONDENSER
Application
Desiccant
Type
CapacityDescription
XH - 9 (30g)
Aluminum type
240cc
RECEIVER DRIER
Application
High
LowDescription
OFF: 27±2kgf / cm
2, DIFF : 6±2kgf / cm2
OFF : 1.8±0.2kgf / cm2, ON 1.9±0.3kgf/ cm2
DUAL PRESSURE SWITCH
SPECIFICATIONS
COOLING CAPACITY
Application
Type
Max. Capacity
Max. Blowing Capacity
Refrigerant
Refrigerant AmountDescription
Air mix type
4,500kcal/h
7.Om
3/min
R134a
650 - 75Og
Application
Model
Type
Output
Oil
Magnetic Clutch OutputDescription
FK- ll
Vane rotary type
140.5cc/rev
ZXL 200PG (PAG oil)
45W
COMPRESSOR

MANUAL & SEMIAUTO-HVAC 7B/C-5
Action
Clean oily plate using cleaning agent.
Charge battery or check for cause.
Check wire continuity
Check A/C switch and fan switch for continuity and ground.
DEFECTIVES IN FAN MOTOR CIRCUIT
Fan Motor Does Not Run
Checks
Blown fuse
Battery voltage is low
Faulty wiring
Faulty groundAction
Check for short and replace fuse.
Check battery voltage.
Check connectors’ connection.
Do not apply grease. This can cause voltage down.
Remove body painting and completely ground,
Tighten ground bolts and make sure body ground connection.
Checks
Blown resister temperature fuse
Air leakage in parts connection
Action
Replace resistor.
Check heater, cooling unit and blower for proper connection.
Fan Motor Runs in ‘4’position Only (‘3’, ‘2’, ‘1’ : Does Not Run)
Frosted Evaporator
DEFECTIVES IN COMPRESSOR CIRCUIT
Compressor Does Not Run
Checks
Faulty thermo ampAction
Frosted evaporator reduces cooling capacity.
Off compressor and maximize blowing capacity
Checks
Faulty high/low pressure
Faulty A/C relayAction
Check compressor magnet voltage supply.
A/C relay.
Checks
Oily clutch plate
Low voltage
Faulty electric connection or operation
Magnetic Clutch Slips /Idles
Checks
Clogged or blocked intake grilleAction
Clogged or blocked intake grille reduces blowing capacity.
Motor Runs With Poor Blowing
Checks
Excessive clearance between
Clutch plate and clutch coilAction
Adjust clutch clearance (0.2-0.6mm).
Magnetic Clutch Plays By Hand Only

9A-6 BODY WIRING SYSTEM
Engine Room Fuse (EF) and Relay Box
1 Fuse (15A) : ABS, ABD
2 Fuse (20A) : Sun Roof
3 Fuse (10A) : Air Bag
4 Fuse (15A) : Audio, Clock, Out Side Mirror
5 Fuse (30A) : Cigarette lighter, Power Socket
6 Fuse (30A) : Heater
7 Fuse (15A) : Door Lock
8 Fuse (30A) : Rear Heated
9 Fuse (10A) : Audio, Buzzer, Chime, Clock
10 Fuse (30A) : Power Window
11 Fuse (10A) : Immobilizer
12 Fuse (20A) : T/C
13 Fuse (15A) : Interior Lamp
14 Fuse (15A) : Hazard Lamp
15 Fuse (15A) : Stop Lamp
16 Fuse (15A) : Turn signal Lamp, Head Lamp
17 Fuse (10A) : Back up Lamp
18 Fuse (15A) : Cluster, STICS
19 Fuse (15A) : A/T, Diagnosis
20 Fuse (15A) : Over Voltage Protection Relay
(Gasolin Only)
21 Fuse (15A) : Seat Heater
22 Fuse (15A) : ECS
23 Fuse (15A) : Front Wiper & Washer
24 Fuse (10A) : Rear Wiper & Washer, A/C
25 Relay : Front Wiper26 Relay : ABS Warning Lamp
27 Relay : Flasher Unit
28 Relay : Fuel Pump (Gasoline Only)
29 Relay : Shift Lock (A/T)
30 Relay : Clutch Interlock & Neutral
31 Relay : Sun Roof
32 Relay : A/T ‘B’ Interlock (MB A/T)
33 Relay : Power Window
34 Relay : Rear Fog Lamp
35 Relay : ECS
36 Relay : Compressor (Diesel E/G)
Condenser Fan (Gasoline E/G)
37 Relay : Condenser Fan
38 Relay : Air Conditioner
39 Fuse (10A) : Tail Lamp
40 Fuse (15A) : Head Lamp(LH)
41 Fuse (15A) : Head Lamp(RH)
42 Fuse (15A) : Front Fog Lamp
43 Fuse (10A) : Horn
44 Fuse (10A) : Compressor
45 Relay : Resistor with Diode (Gasoline E/G)
46 Relay : Front fog Lamp
47 Relay : Condenser Fan
48 Relay : Tail Lamp
49 Relay : Horn

9A-8 BODY WIRING SYSTEM
1 Fuse Box
2 Door Lock Relay
3 Relay Box
3.1 Front Wiper Relay
3.2 ABS Warning Lamp Relay....................................ABD 5.0
3.3 Flasher Unit
3.4 Fuel Pump Relay.................................................Gasoline E/G
3.5 Shift Lock Relay...................................................Automatic Transmission
3.6 Clutch Interlock & Neutral Relay...........................Manual Transmission or Automatic Transmission
3.7 Sun Roof Relay
3.8 Automatic Transmission ‘B’ Switch Interlock.......Automatic Transmission
3.9 Power Window Relay
3.10 Rear Fog Lamp Relay..........................................Rear Fog Lamp
3.11 ECS Relay
4 Defogger Relay
5 Ground 1
6 Roof Wiring Connector
7 Diode 1
8 Front Door Wiring Connector
9 Front Door Wiring Connector
10 Front Door Wiring Connector
11 Front Door Wiring Connector
12 Kick Down Relay..................................................Automatic Transmission
13 Floor Wiring Connector
14 Floor Wiring Connector
15 Floor Wiring Connector
16 ABD Floor Wiring Connector................................ABD 5.0
17 ECS Floor Wiring Connector
18 Rear Iper & Washer Switch
19 Clutch Switch........................................................Manual Transmission
19-1Clutch Switch........................................................E32 Gasoline E/G with Manual Transmission
20 Stop Lamp Switch
21 Outside Mirror Switch
22 Ignition Switch
23 Multi Function Switch
24 Multi Function Switch
25 Black Out Switch..................................................Black Out Lamp
26 Black out switch...................................................Black Out Lamp
27 Joint Connector (Tail)
28 Joint Connector (Ignition)
29 Cluster
30 Cluster .................................................................Automatic Transmission
31 Cluster
32 Cluster
33 4WD Switch..........................................................Except TOD
33-14WD Switch.......................................................... TOD
3 4 Hazard Switch
35 Ground 2
36 Pedal Module.......................................................Gasoline E/G with MSE ECU
37 Audio Switch
3 8 Immobilizer...........................................................Crypto Type, Gasoline E/G with MSE ECU or Diesel E/G
39 Ignition Switch
40 Multi Function Switch
4 1 STICS
4 2 STICS
4 3 REKES.................................................................Remote Keyless