service SSANGYONG MUSSO 1998 Workshop Repair Manual

9L-4 GLASS AND MIRRORS
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
FRONT & SIDE GLASS

GLASS AND MIRRORS 9L-13
Check & Service
If reflection ratio is not adjusted automatically during night
driving when AUTO switch is pressed, check each connectors
for proper connection and power flow to the auto dimming room
mirror using multi tester.
1. Yellow (Connected to back-up lamp)
2. Blue (Ground)
3. White (Power)
Voltage Rating
Operating Current
Over CurrentDV 12V
1 A
3 A
Function
When ignition switch is turned ON, green lamp on auto dimming
mirror will turn in and glare reflection ratio will be automatically
adjusted. By positioning AUTO switch to ON, 2Sensors will
automatically adjust refection ratio after sensing rear and
surrounding brightness to reduce driver’s eye fatigue during
driving though tunnel or in night.
When OFF switch is pressed, the lamp goes out and it will be
operated as a normal rear view mirror and shift lever is
positioned in reverse, the auto dimming function will be
automatically OFF.
Specifications

SECTION 9O
BUMPERS AND FASCIAS
TABLE OF CONTENTS
Maintenance and Repair . . . . . . . . . . . . . . . 9O-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . 9O-2Front Bumper . . . . . . . . . . . . . . . . . . . . . . . . . 9O-2
Rear Bumper . . . . . . . . . . . . . . . . . . . . . . . . . 9O-4

9O-2 BUMPERS AND FASCIAS
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
FRONT BUMPER
Notice
Removal and installation is as shown in upper drawings.

SECTION 9P
DOORS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Schematic and Routing Diagrams . . . . . . . . 9P-2
Power Window . . . . . . . . . . . . . . . . . . . . . . . . 9P-2
Maintenance and Repair . . . . . . . . . . . . . . . 9P-3
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . 9P-3Front Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 9P-3
Rear Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9P-4
Tail Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9P-5

DOORS 9P-3
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
FRONT DOOR
Removal & Installation Procedure
1. Remove the pin from the center hinge of the door.
2. Remove the upper/lower hinge bolts from the body and
remove the door assembly.
3. Installation should follow the removal procedure in the
reverse order.

SECTION 9Q
ROOF
TABLE OF CONTENTS
Schematic and Routing Diagrams . . . . . . . . 9Q-2
Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Q-2
Maintenance and Repair . . . . . . . . . . . . . . . 9Q-3
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . 9Q-3
Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Q-3

ROOF 9Q-3
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
SUN ROOF
1 Inner Sliding Sun Roof Assembly
2 Sun Roof Body Mounting Bracket
3 Drain Hose Rear Grommet
4 Sun Roof Motor Spanner
5 Mounting Clip6 Mounting Bracket
7 Mounting Bracket Assembly
8 Sun Roof Mounting Bracket
11 Sun Roof Module Assembly

SECTION 9R
BODY FRONT END
TABLE OF CONTENTS
Maintenance and Repair . . . . . . . . . . . . . . . 9R-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . 9R-2Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9R-2
Fender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9R-5

9R-2 BODY FRONT END
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
HOOD
1 Hood
2 Sping3 Hood Hinge Assembly
4 Bolt