wheel torque SSANGYONG MUSSO 1998 Workshop Repair Manual
[x] Cancel search | Manufacturer: SSANGYONG, Model Year: 1998, Model line: MUSSO, Model: SSANGYONG MUSSO 1998Pages: 1463, PDF Size: 19.88 MB
Page 27 of 1463

GENERAL INFORMATION 0B-15
GENERAL DESCRIPTION
AND SYSTEM OPERATION
GENERAL REPAIR INSTRUCTIONS
lIf a floor jack is used, the following precautions are
recommended.
lPark the vehicle on level ground, “block” the front or
rear wheels, set the jack against the frame, raise the
vehicle and support it with chassis stands and then
perform the service operation.
lBefore performing the service operation, disconnect
the negative battery cable in order to reduce the
chance of cable damaged and burning due to short-
cir cuiting.
lUse a cover on the body, the seats and the floor to
protect them against damage and contamination.
lHandle brake fluid and antifreeze solution with care
as they can cause paint damage.
lThe use of proper tools, and the recommended
essential and available tools where specified, are
important for efficient and reliable performance of
the service repairs.lUse genuine DAEWOO parts.
lDiscard used cotter pins, gaskets, O-rings, oil seals,
lock washers and self-locking nuts. Prepare new ones
for installation. Normal function of these parts cannot
be maintained if these parts are reused.
lKeep the disassembled parts neatly in groups to
facilitate proper and smooth reassembly.
lKeep attaching bolts and nuts separated, as they
vary in hardness and design depending on the
position of the installation.
lClean the parts before inspection or reassembly.
lAlso clean the oil parts, etc. Use compressed air to
make certain they are free of restrictions.
lLubricate rotating and sliding faces of parts with oil
or grease before installation.
lWhen necessary, use a sealer on gaskets to prevent
leakage.
lCarefully observe all specifications for bolt and nut
torques.
lWhen service operation is completed, make a final
check to be sure service was done properly and the
problem was corrected.
Page 117 of 1463

1B1-44 M162 ENGINE MECHANICAL
Engine Lock 602 589 00 40 00
2. Remove the start motor and install the engine lock to the
flywheel ring gear.
3. Remove the center bolt.
Installation Notice
Tightening Torque1st step 200 - 220 Nm
2nd step 90° +10°
4. Remove the vibration damper assembly using the puller.
5. Installation should follow the removal procedure in the
reverse order.
Notice
If possible, don’t separate the vibration damper and the
pulley.
Page 126 of 1463

M162 ENGINE MECHANICAL 1B1-53
FLYWHEEL / DRIVEN PLATE
Preceding Work : Removal of manual or automatic transmission
1 Flywheel Mounting Bolt (M10 x 22, 8 pieces)
...............................................1st step 45+5 Nm
2nd step +90° +10°
2 Plate3 Driven Plate (A/T)
4 Dowel Pin
Service Data Standard (Stretch Bolt)
Nominal Size
Stretch Side Diameter
Bolt Length
Tightening TorqueM x 1.5
8.5 - 0.2 mm
8.0 mm
21.8 - 22.2 mm-
When New
Min. Diameter
When NewD
d
L
1st step 50 Nm, 2nd step 90°
Page 127 of 1463

1B1-54 M162 ENGINE MECHANICAL
Removal & Installation Procedure
1. Unscrew the stretch bolt.
Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Crankshaft Front Seal
4 Flywheel MTG Bolt
5 Crankshaft
6 Dowel Pin
7 Plate
8 TGCC
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear
lReplace the bolt when the stretch side diameter (d) of
the flywheel mounting bolt is less than 8.0mm.
lFor the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles, or
the driven plate (3), and plate (2) for Auto. transmission
vehicle.
3. Installation should follow the removal procedure in the
reverse order.Tightening Torque1st step 45+5 Nm
2nd step 90° + 10°
Page 240 of 1463

M161 ENGINE MECHANICAL 1B2-51
Engine Lock 602 589 00 40 00
2. Remove the start motor and install the engine lock to the
flywheel ring gear.
3. Remove the center bolt.
Installation Notice
4. Remove the vibration damper assembly using the puller.
5. Installation should follow the removal procedure in the
reverse order.
Notice
If possible, don’t separate the vibration damper and the
pulley.Tightening Torque1st step 180 - 220 Nm
2nd step + 90°
Page 249 of 1463

1B2-60 M161 ENGINE MECHANICAL
FLYWHEEL/DRIVEN PLATE
Preceding Work : Removal of manual or automatic transmission
1 Flywheel Mounting Bolt
(M10 x 22, 8 pieces) ................ 1st Step 45 Nm
2nd Step 90°+10°
2 Plate3 Driven Plate (A/T)
4 Dowel Pin
5 Flywheel (M/T)
Service Data Standard (Stretch Bolt)
Nominal Size
Stretch Side Diameter
Bolt Length
Tightening TorqueM x 1.5
8.5 - 0.2 mm
8.0 mm
21.8 - 22.2 mm-
When New
Min. Diameter
When NewD
d
L
1st step 50 Nm, 2nd step 90°
Page 250 of 1463

M161 ENGINE MECHANICAL 1B2-61
Removal & Installation Procedure
1. Unscrew the stretch bolt.
Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Radial Seal
4 Bolt
5 Crankshaft
6 Dowel Pin
7 Washer (Thickness : 3.5 mm)
8 Washer
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear
lReplace the bolt when the stretch side diameter (d) of
the flywheel mounting bolt is less than 8.0mm.
lFor the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles,
or the driven plate (3), and plate (2) for Auto. transmission
vehicle.
3. Installation should follow the removal procedure in the
reverse order.Tightening Torque1st step 45 Nm
2nd step90°+5°
Page 397 of 1463

OM600 ENGINE MECHANICAL 1B3-95
3. Remove the flywheel (3), if equipped with manual
transmission.
Installation Notice
Correctly align the position of dowel pin (2).
Tools Required
602 589 00 40 00 Engine Lock
Removal & Installation Procedure
1. Install the engine lock.
Engine Lock 602 589 02 40 00
2. Remove the 12-sided stretch bolts (4).
Installation Notice
Tightening Torque 45 Nm + 90°
Notice
If the length ‘L’ of bolts exceeds 22.5mm, replace the bolts.
Page 635 of 1463

M162 ENGINE CONTROLS 1F1-65
1 Crankshaft Position Sensor
2 Bolt (M6 X 14)........................................ 9 -11Nm
CRANKSHAFT POSITION SENSOR
Removal & Installation Procedure
1. Disconnect the wiring connector at the crankshaft position
sensor.
2. Unscrew the bolt and remove the crankshaft position sensor
unit.
Installation Notice
3. Installation should follow the removal procedure in the
reverse order.3 Segment
4 Flywheel
Tightening Torque 9 -11Nm
Page 844 of 1463

FRONT SUSPENSION 2C-7
Removal & Installation Procedure
1. Remove the fixing nuts and bolts of the shock absorber
and lower arm connection.
Installation Notice
2. Remove the connecting nuts of the stabilizer bar link to the
lower arm.
Installation Notice
3. Turn the height control bolt until the distance between the
end of the height control bolt end piece and the bolt end
becomes 0-5 mm.
Installation Notice
Install the torsion bar spring and adjust the distance between
the end of the height control bolt and piece end the bolt
end to be 50-55 mm. Adjust the vehicle height.
Tightening Torque 60 - 80 Nm
Tightening Torque 16 - 22 Nm
4. Remove the torque arm fixing nuts and bolts and then
withdraw the torsion bar spring.
Installation Notice
M10
M12Tightening Torque40 - 60 Nm
60 - 80 Nm
5. Installation should follow the removal precedure in the
reverse order.
6. Check and adjust the wheel alignment.