oil SSANGYONG MUSSO 1998 Workshop Repair Manual

3C-2 PROPELLER SHAFT
1 Flange Yoke
2 Cross and Bearing Assembly (with Snap Ring)
3 Cross and Bearing Assembly (with Snap Ring)
4 Slip Yoke Assembly
5 Grease Nipple
6 Dust Cap
7 Oil Seal
8 Split Washer
9 Slip Tube Shaft
10 Tube
Notice
Only the length of shaft is different and the components of front/rear shaft are the same.
(The deadener is inserted to the inside of tube of rear shaft, both ends)
COMPONENT LOCATOR
M/T & A/T (PART-TIME T/C)
1. Gasolin : E32
- Fromt Propeller Shaft
2. Diesel/Gasolin : E23,20
- Fromt Propeller Shaft
: A/T + Full - Time T/C
3. Gasolin
- Rear Propeller Shaft
Diesel
- Fromt & Rear Propeller Shaft
: M/T & A/T + FPart - Time T/C
11 Tube Yoke
12 Flange Yoke
13 Diesel : Cross and Bearing Assembly (with Snap Ring)
Gasoline : CV Joint (DOJ)
14 Diesel : Double Cardan
Gasoline : Stub Shaft
15 Tube
16 Cross and Bearing Assembly (with Snap Ring)
17 Center Couping Yoke
18 Boots Band

SECTION 3D
REAR DRIVE AXLE
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3D-1
General Specifications . . . . . . . . . . . . . . . . . . 3D-1
Fastener Tightening Specifications . . . . . . . . . 3D-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Noise (During Straight Driving) . . . . . . . . . . . . 3D-3
Oil Leakage . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Noise (During Turning) . . . . . . . . . . . . . . . . . . 3D-3
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-4Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-4
Component Locator . . . . . . . . . . . . . . . . . . . 3D-5
Maintenance and Repair . . . . . . . . . . . . . . . 3D-6
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3D-6
Axle Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-6
Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-9
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 3D-11
Axle Housing . . . . . . . . . . . . . . . . . . . . . . . . . 3D-11
LSD (Limited Slip Diffrential) . . . . . . . . . . . . . 3D-16
SPECIFICATIONS
GENERAL SPECIFICATIONS
Axle Shaft Type
Axle Housing Type
Differential
Reduction Ratio
Type
Gear
M/T
M/T
A/T (MB)
M/T
A/T (BTRA)
M/T
A/T (BTRA)
Description
Semi - floating
Salibury (Build-up)
Conventional Type
Hypoid Gear
4.55
4.55
3.73
4.55
5.38
4.27
4.89Application
661NA
662NA
661LA
662LA

3D-2 REAR DRIVE AXLE
FASTENER TIGHTENING SPECIFICATIONS
Application
Inner Bracket Mounting Nut
Propeller Shaft to Rear Axle Input Shaft
Lower Arm Mounting Nut
Lower Shock Absorber to Axle Housing
Upper Arm Mounting Nut
Stabilizer Bar Mounting Bolt
Lateral Rod Mounting Nut
Drive Pinion Lock Nut
Oil Drain Plug
Ring Gear Mounting Bolt
Oil Filler PlugN
· ·· ·
·m
50 - 65
70 - 80
150 - 180
50 - 65
150 - 180
30 - 45
150 - 180
240 - 310
28 - 42
75 - 90
28 - 42
4.55
4.55
4.55
4.27
5.86
3.73
3.73
4.89
1.9 L
SEA 80W/90, API GL - 5 M/T
A/T (MB)
M/T
A/T (MB)
A/T (BTRA)
M/T
A/T (MB)
A/T (BTRA)
Oil Capacity
Oil Specification
ApplicationDescription
GENERAL SPECIFICATIONS(CONT'D)
E20
E23
E32 Reduction Ratio

REAR DRIVE AXLE 3D-3
Checks
Worn or Damaged Tooth of Pinion or Side Gear
Worn Pinion Shaft
Excessive Backlash of Pinion Gear and Side Gear
Excessive End-play of Rear Axle Shaft
Incorrect Contact of Side Gear and Differential Case
Axle Housing Crack
Bent or Poor Installation of Drive Pinion Oil Seal
Damaged or Torn Drive Pinion Oil Seal
Loosened Bearing Collar
Worn or Damaged Universal Joint
Worn or Damaged Axle Shaft BearingChecks
Excessive Oil
Faulty Seal of Carrier Contact Surface
Axle Housing Crack
Worn or Damaged Oil SealChecks
Lack of Oil
Low Viscosity of Oil
Insufficient Oil
Excessive Backlash of Ring Gear
Worn or Damaged Tooth of Ring and Pinion Gear
Worn or Damaged Drive Pinion Bearing
Bent Axle Housing
Bent Differential Case
Worn Pinion Shaft
Incorrect Drive Pinion Preload
Incorrect Contact of Ring Gear and Pinion
DIAGNOSIS
NOISE (DURING STRAIGHT DRIVING)
Action
Replenish
Replace
Replace
Adjust
Replace
Replace
Replace
Replace
Replace
Adjust
Retightening
OIL LEAKAGE
Action
Adjust
Repair
Replace
Replace
NOISE (DURING TURNING)
Action
Replace
Replace
Replace
Adjust
Replace
Replace
Replace
Replace
Replace
Replace
Replace
HEATING
Checks
Lack of Oil
Insufficient Backlash of Gears
Excessive Preload of BearingAction
Replenish
Adjust
Adjust

REAR DRIVE AXLE 3D-5
1 Spring Seat
2 Coil Spring
3 Lateral Rod
4 Shock Absorber5 Upper Arm
6 Lower Arm
7 Connecting Link
8 Stabilizer Bar
COMPONENT LOCATOR

3D-10 REAR DRIVE AXLE
6. Separate the lower shock absorber from the axle housing.
Installation Notice
7. Remove the upper arm mounting nuts and remove the
upper arm form the axle housing.
Installation Notice
Tightening Torque 50 - 65 Nm
8. Remove the stabilizer bar.
Installation Notice
Tightening Torque 150 - 180 Nm
9. Remove the lateral rod mounting nuts and remove the
lateral rod from the axle housing.
Installation Notice
Tightening Torque 30 - 45 Nm
10. Lowering the axle housing slowly, remove the coil springs
and spring seats.
11. Installation should follow the removal precedure in the
reverse order.
Tightening Torque 150 - 180 Nm

REAR DRIVE AXLE 3D-11
UNIT REPAIR
AXLE HOUSING
Preceding Work : Removal of the axle shaft
Removal of the axle housing
1 Drive Pinion Lock Nut......................240-310 Nm
2 Washer
3 Companion Flange
4 Pinion Oil Seal
5 Bearing Slinger
6 Bearing
7 Shim
8 Shim
9 Bearing Cup
10 Breather Nipple
11 Rear Axle Housing
12 Oil Drain Plug.......................................28-42 Nm
1 3 Shim
14 Bearing
15 Drive Pinion
16 Bearing Cap1 7 Bolt....................................................87-124 Nm
18 Bearing
1 9 Shim
20 Ring Gear
21 Shaft Lock Pin
22 Differential Case
23 Ring Gear Mounting Bolt......................75-90 Nm
24 Thrust Washer
25 Differential Pinion
26 Thrust Washer
27 Side Gear
28 Differential Shaft
29 Housing Cover
3 0 Bolt......................................................38-46 Nm
31 Oil Filler Plug.......................................28-42 Nm

3D-12 REAR DRIVE AXLE
Disassembly Procedure
1. Remove the drain plug and drain the oil. Reinstall the drain
plug.
2. Remove the axle housing cover.
Notice
Clean the cover and housing contact surface.
3. Remove the bearing cap bolts and remove the bearing caps.
Pull out the differential carrier assembly.
Notice
Place alignment marks on the bearing cap not to change
the caps before removal. When pulling out the differential
carrier assembly, be careful not to damage the axle housing.
4. Disassemble the parts of the differential carrier assembly.
Tightening Torque 28 - 42Nm

3D-16 REAR DRIVE AXLE
LSD (LIMITED SLIP DIFFERENTIAL)
1 Limited Slip Differential Assembly
2 Shaft, Hub (left)
3 Shim
4 Thrust Washer
5 Face Cam (left)
6 Cam Whillom
7 Thrust Bearing
8 Radial Bearing9 Shaft, Hub (right)
10 Thrust Washer
11 Face Cam (right)
12 Cage
13 Thrust Bearing
14 Plate Spring
15 Radial Bearing
16 Oil Catcher

4A-2 HYDRAULIC BRAKES
Check
Dirty or Lack of Fluid
Air in Brake System
Faulty Brake Booster
Poor Contact of Pad or Lining
Oil or Grease on Pad
Faulty Auto Adjuster
Over Heated Rotor Due to Dragging Pad or Lining
Clogging Brake Line
Faulty Proportioning ValveCheck
Incorrect Tire Pressure Between Left and Right
Poor Contact of Pad or Lining
Oil or Grease is Applied to Pad or Lining
Bent or Uneven Wear of Drum
Incorrectly Mounted Wheel Cylinder
Faulty Auto AdjusterAction
Repair
Retighten
Replace
Replace
Repair
Repair
Lubricate
Retighten Check
Incorrectly Mounted Back Plate or Caliper
Loosened Bolt of Back Plate or Caliper
Crack or Uneven Wear of Brake Drum or Disc
Pad or Lining Sticking to Contact Surface
Excessive Clearance Between Caliper and Pad
Uneven Contact of Pad
Lack of Lubrication
Loosened Suspension
DIGNOSIS
NOISE OR VEHICLE VIBRATION WHEN APPLIED BRAKE
PULLS TO ONE SIDE WHEN BRAKING
Action
Adjust
Repair
Replace
Replace
Repair
Replace
Action
Replenish or Replace(Check eventual leakage)
Bleeding
Replace
Repair
Replace
Replace
Repair
Repair
Repair
POOR BRAKING
( If low cut-in : Adjust )
( If Leakage : Replace )