oil SSANGYONG MUSSO 1998 Workshop Repair Manual

REAR SUSPENSION 2D-3
HEATING
Check
Lack of Oil
Insufficient Backlash of Gears
Excessive Preload of BearingAction
Replenish
Adjust
Adjust

2D-4 REAR SUSPENSION
1 Spring Seat
2 Coil Spring
3 Lateral Rod
4 Shock Absorber5 Upper Arm
6 Lower Arm
7 Connecting Link
8 Stabilizer Bar
COMPONENT LOCATOR

REAR SUSPENSION 2D-5
MAINTENANCE AND REPAIR
ON-VEHICLE SERIVCE
REAR SUSPENSION (5 - LINK)
1 Spring Seat
2 Coil Spring
3 Lateral Rod
4 Shock Absorber5 Upper Arm
6 Lower Arm
7 Connecting Link
8 Stabilizer Bar

2D-6 REAR SUSPENSION
Removal & Installation Procedure
lStabilizer bar
1. Remove the upper nut of the connecting link.
Installation Notice
2. Remove the stabilizer bar cap fixing bolts (arrow) and
remove the stabilizer bar.
Installation Notice
Tightening Torque 16 - 22 Nm
Distance Between the Nut
end and the Screw end10 - 13 mm
Tightening Torque 30 - 45 Nm
lLateral Rod
1. Remove the lateral rod fixing nut from the frame.
Notice
Completely press the coil springs.
Installation Notice
2. Remove the lateral rod fixing nut from the rear axle and
remove the lateral rod.
Installation Notice
Tightening Torque 150 - 180 Nm
Tightening Torque 150 - 180 Nm

TIRES AND WHEELS 2E-7
lTo correct unbalance, install equal weights 180° opposite
each other, one on the inside of the wheel and one on
the outside, at the point of unbalance.
lBalance Weight
6. Cautions for installation and removal.
lClean the mounting surfaces of hub and wheel.
lDo not apply grease or oil on the nuts and bolts (It will
cause looseness and poor tightening).
lUsing a jack, lift up the tire about 3cm from the ground.
lTighten nuts in a criss-cross pattern 2-3 times.
10g
0.4oz20g
0.7oz30g
1.10oz40g
1.40oz50g
1.80oz60g
2.1oz
Steel : 80 - 120Nm
Aluminium : 110 - 130NmTighten Torque

M/T
M/T
A/T (MB)
M/T
A/T (BTRA)
M/T
A/T (BTRA)
M/T
A/T (MB)
M/T
A/T (MB)
A/T (BTRA)
M/T
A/T (MB)
A/T (BTRA)
SECTION 3A
FRONT DRIVE AXLE
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3A-1
General Specifications . . . . . . . . . . . . . . . . . . 3A-1
Fastener Tightening Specifications . . . . . . . . . 3A-2
Component Locator . . . . . . . . . . . . . . . . . . . 3A-3
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-3
Auto-Locking Hub . . . . . . . . . . . . . . . . . . . . . . 3A-4
Vacuum Circuit . . . . . . . . . . . . . . . . . . . . . . . . 3A-5
Maintenance and Repair . . . . . . . . . . . . . . . 3A-6
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3A-6
Vacuum Line . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-6
Steering Knuckle and Drive Shaft . . . . . . . . . . 3A-8
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-14
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Axle Housing . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Application
Drive Shaft Type
Axle Housing Type
Differential Type
Differential Gear
CV Joint
Build - up
Conventional
Hypoid Gear
4.56
4.56
3.73
4.56
5.38
4.27
4.89
4.89
4.55
4.55
4.55
5.86
3.73
3.73
4.89
1.4 L
SAE 80W/90, API GL - 5
Description
661NA
662NA
661LA
662LA
E20
E23
E32 Reduction Ratio
Oil Capacity
Oil Specification

3A-4 FRONT DRIVE AXLE
AUTO-LOCKING HUB
1 Cap
2 Filter
3 Vacuum Diaphragm
4 Diaphragm Retainer
5 Piston
6 Bolt (M10)
7 Lock Washer
8 O-ring
9 Retaining Ring
10 Clutch Ring11 Body
12 Return Spring
13 Bearing
14 O-ring
15 Retaining Ring
16 Inner Drive Gear
17 Oil Seal
18 Oil Seal Race
19 Axle Retaining Ring

FRONT DRIVE AXLE 3A-17
1 Front Axle Housing Mounting Bracket
2 Inner Shaft (Left)
3 Bolt......................................................55-65 Nm
4 Oil Seal.................................................. Replace
Apply Grease to the Sealing Rib
5 Snap Ring
6 Bearing
7 Snap Ring
8 Oil Drain Plug.......................................28-41 Nm
9 Front Axle Housing
10 Breather Nipple
11 Inner Shaft (Right)
12 Pinion Lock Nut................................240-310 Nm
13 Washer
14 Companion Flange
15 Oil Seal.................................................. Replace
Apply Grease to the Sealing Rib
16 Bearing
1 7 Shim
18 Bearing Baffle
1 9 Shim20 Bearing
21 Oil Slinger
22 Drive Pinion
23 Oil Filler Plug.......................................28-41 Nm
2 4 Bolt......................................................39-46 Nm
25 Axle Housing Cover..............Apply Liquid Gasket
to the Contact Surface
26 Ring Gear
27 Bearing
2 8 Shim
29 Shaft Lock Pin
30 Differential Case
3 1 Bolt......................................................75-90 Nm
3 2 Bolt......................................................48-69 Nm
33 Washer
34 Bearing Cap
35 Thrust Washer
36 Side Gear
37 Differential Shaft
38 Differential Pinion
39 Thrust Washer

3A-18 FRONT DRIVE AXLE
Disassembly Procedure
1. Remove the drain plug and drain the oil. Reinstall the drain
plug.
Installation Notice
Tightening Torque 28 - 41 Nm
2. Unscrew the axle housing and housing mounting bracket
bolts and remove the bracket and inner shaft assembly.
3. Remove the bearing fixing snap ring of the inner shaft and
pull out the bearing. Separate the inner shaft and the
mounting bracket.
4. Remove the axle housing cover.
Notice
Clean the cover and housing contact surfaces.

FRONT DRIVE AXLE 3A-21
6. Measure backlash of the drive pinion and ring gear.
7. Install the axle housing cover.
8. Assemble the parts of the front axle shaft and housing
mounting bracket.
Notice
Apply grease to the oil seal rib.
9. Align the axle shaft and differential carrier spline and insert
the axle shaft. Assemble the axle housing mounting bracket
to the axle housing.
Specified Value 0.13 - 0.20 mm
Tightening Torque 39 - 46 Nm
Tightening Torque 55 - 65 Nm