drain bolt SSANGYONG MUSSO 1998 Workshop Owner's Guide

1D2-16 M161 ENGINE COOLING
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermo connector from the radiator.
3. Remove the each coolant hoses.
Tightening Torque 14 Nm
4. Remove the automatic transmission oil cooling hose.
Installation Notice
5. Unscrew the bolts from radiator bracket and remove the
bracket and insulator.
Installation Notice
Tightening Torque 3 - 7 Nm
6. Remove the radiator upper mounting bolts and then
remove the bracket and insulator.
7. Remove the radiator.
8. Check the radiator pin for crack, damage, leakage and
bending and replace if necessary.
9. Installation should follow the removal procedure in the
reverse order.
10. Berform the cooling system leakage test.

SECTION 1D3
OM600 ENGINE COOLING
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1D3-1
General Specifications . . . . . . . . . . . . . . . . . 1D3-1
Fastener Tightening Specifications . . . . . . . . 1D3-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1D3-2
Cooling Circulation . . . . . . . . . . . . . . . . . . . . 1D3-2
Thermostat Operation . . . . . . . . . . . . . . . . . 1D3-3
Cooling System Leakage Test . . . . . . . . . . . 1D3-4
Maintenance and Repair . . . . . . . . . . . . . . 1D3-5On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1D3-5
Drain and Filling of Coolant . . . . . . . . . . . . . 1D3-5
Coolant Pump . . . . . . . . . . . . . . . . . . . . . . . . 1D3-6
Coolant Pump Housing . . . . . . . . . . . . . . . . . 1D3-8
Cooling Fan Clutch . . . . . . . . . . . . . . . . . . . 1D3-10
Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1D3-12
Cooling Sub-System . . . . . . . . . . . . . . . . . . 1D3-14
Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . 1D3-16
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Application
Coolant
Mixing Ratio (Water : anticorrosion)
CapacityDescription
ALUTEC P- 78
50 : 50
10.5L - 11L
9.5L - 10L
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Coolant Pump Bolt
Belt Pulley Bolt
Coolant Pump Housing Return Pipe Bolt
Thermostat Bolt
Cooling Fan Clutch Socket Bolt (Center)
Cooling Fan Clutch Socket Bolt (Side)
Radiator Bolt
Coolant Sub-tank BoltN
· ·· ·
·m
10
10
10
10
45
10
3 - 7
3 - 7
FASTENER TIGHTENING SPECIFICATIONS
662LA
661LA

OM600 ENGINE COOLING 1D3-13
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermoswich connector from radiator.
3. Remove the each coolant hose.
4. Remove the auto T/M oil cooling hose and cooling line.
Installation Notice
5. Loosen the radiator upper mounting bolt and remove the
mounting stopper and insulator.
6. Remove the radiator.
7. Check the radiator pin for crack, leakage and bending and
replace it if necessany.
8. Installation should follow the removal procedure in the
reverse order.
Tightening TorqueHose : 29 - 40Nm

OM600 ENGINE COOLING 1D3-15
Removal & Installation Procedure
Cooling Fan Shroud
1. Remove the radiator deaeration hose and tube.
Installation Notice
Tightening Torque 3 - 7 Nm
Tightening torque 3-7Nm
2. Check the shroud.
3. Installation should follow the removal procedure in the
reverse order.
Coolant Sub-Tank
1. Drain the coolant from radiator.
2. Remove the each hose.
3. Loosen the mounting bolt of sub-tank and remove the
coolant sub-tank.
Installation Notice
4. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 3 - 7 Nm

OM600 ENGINE COOLING 1D3-17
Removal & Installation Procedure
1. Drain the coolant completely.
2. Disconnect the coolant hose(4) from the thermostat housing
cover(3).
3. Remove the bolts(5) and then remove the thermostat(1)
and housing cover(3)
Installation Notice
Align the groove on thermostat and the housing cover
rib(arrow).
Tightening Torque 10 Nm
Notice
Replace the seal(2).
4. Installation should follow the removal procedure in the
reverse order.

1F1-60 M162 ENGINE CONTROLS
Tools Required
661 589 00 46 00 Cap Remover
Removal & Installation Procedure
1. Disconnect the negative battery cable.
2. Disconnect the harness connector (1).
3. Disconnect the fuel supply (6) and return (5) pipes.
4. Using a special tool, Unscrew the eight fuel retaining bolts
and remove the pump from fuel tank.
Notice
Check the condition of the seal and replace if necessary.
Drain the fuel before removing the pump.

1F2-60 M161 ENGINE CONTROLS
Tools Required
661 589 00 46 00 Cap Remover
Removal & Installation Procedure
1. Disconnect the negative battery cable.
2. Disconnect the harness connector (1).
3. Disconnect the fuel supply (6) and return (5) pipes.
4. Using a special tool, Unscrew the eight fuel retaining bolts
and remove the pump from fuel tank.
Notice
Check the condition of the seal and replace if necessary.
Drain the fuel before removing the pump.

FRONT DRIVE AXLE 3A-17
1 Front Axle Housing Mounting Bracket
2 Inner Shaft (Left)
3 Bolt......................................................55-65 Nm
4 Oil Seal.................................................. Replace
Apply Grease to the Sealing Rib
5 Snap Ring
6 Bearing
7 Snap Ring
8 Oil Drain Plug.......................................28-41 Nm
9 Front Axle Housing
10 Breather Nipple
11 Inner Shaft (Right)
12 Pinion Lock Nut................................240-310 Nm
13 Washer
14 Companion Flange
15 Oil Seal.................................................. Replace
Apply Grease to the Sealing Rib
16 Bearing
1 7 Shim
18 Bearing Baffle
1 9 Shim20 Bearing
21 Oil Slinger
22 Drive Pinion
23 Oil Filler Plug.......................................28-41 Nm
2 4 Bolt......................................................39-46 Nm
25 Axle Housing Cover..............Apply Liquid Gasket
to the Contact Surface
26 Ring Gear
27 Bearing
2 8 Shim
29 Shaft Lock Pin
30 Differential Case
3 1 Bolt......................................................75-90 Nm
3 2 Bolt......................................................48-69 Nm
33 Washer
34 Bearing Cap
35 Thrust Washer
36 Side Gear
37 Differential Shaft
38 Differential Pinion
39 Thrust Washer

3A-18 FRONT DRIVE AXLE
Disassembly Procedure
1. Remove the drain plug and drain the oil. Reinstall the drain
plug.
Installation Notice
Tightening Torque 28 - 41 Nm
2. Unscrew the axle housing and housing mounting bracket
bolts and remove the bracket and inner shaft assembly.
3. Remove the bearing fixing snap ring of the inner shaft and
pull out the bearing. Separate the inner shaft and the
mounting bracket.
4. Remove the axle housing cover.
Notice
Clean the cover and housing contact surfaces.

3D-2 REAR DRIVE AXLE
FASTENER TIGHTENING SPECIFICATIONS
Application
Inner Bracket Mounting Nut
Propeller Shaft to Rear Axle Input Shaft
Lower Arm Mounting Nut
Lower Shock Absorber to Axle Housing
Upper Arm Mounting Nut
Stabilizer Bar Mounting Bolt
Lateral Rod Mounting Nut
Drive Pinion Lock Nut
Oil Drain Plug
Ring Gear Mounting Bolt
Oil Filler PlugN
· ·· ·
·m
50 - 65
70 - 80
150 - 180
50 - 65
150 - 180
30 - 45
150 - 180
240 - 310
28 - 42
75 - 90
28 - 42
4.55
4.55
4.55
4.27
5.86
3.73
3.73
4.89
1.9 L
SEA 80W/90, API GL - 5 M/T
A/T (MB)
M/T
A/T (MB)
A/T (BTRA)
M/T
A/T (MB)
A/T (BTRA)
Oil Capacity
Oil Specification
ApplicationDescription
GENERAL SPECIFICATIONS(CONT'D)
E20
E23
E32 Reduction Ratio