wheel SSANGYONG MUSSO 1998 Workshop Manual Online

4D-2 FRONT DISC BRAKES
1 Eye-Hose Bolt......................................25-35 Nm
2 Gasket ................................................... Replace
3 Brake Hose
4 Brake Caliper
5 Bolt........................................................... 20 Nm
6 Washer
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
FRONT DISC BRAKE
Preceding Work : Removal of wheels and tires
7 Front Disc Assembly
8 Brake Pad
9 Brake Hose and Nut.............................25-35 Nm
10 Gasket ................................................... Replace
11 Washer
1 2 Bolt....................................................85-105 Nm

FRONT DISC BRAKES 4D-3
Removal & Installation Procedure
1. MANDO Brake
Tightening Torque 25 - 35 Nm
2. PBR Brake
Remove the eye-hose bolt and disconnect the hose.
Installation Notice
Tightening Torque 15 - 18 Nm
3. Remove the wheel speed sensor (for ABS vehicies).
Installation Notice
Tightening Torque 6 - 8 Nm
4. Remove the mounting bolts and then caliper assembly.
Installation Notice
Tightening Torque 85 - 105 Nm
Remove the hose mounting nut and disconnect the hose.
Installation Notice

4D-4 FRONT DISC BRAKES
5. Pull out the brake pads. Replace pads if necessary.
Notice
Always change the all pads on one wheel at a time.
6. Installation should follow the removal procedure in the
reverse order.
7. Bleed the air from the system.

FRONT DISC BRAKES 4D-5
4. Measure rotor disc thickness.
UNIT REPAIR
FRONT DISC BRAKE
Inspection Procedure
1. Clean all components and visually check the followings.
lCheck the cylinder and piston for wear, rust or damage.
lCheck the caliper body and guide pin for wear, damage
or crank.
lCheck the pads for uneven wear or oiliness.
lCheck the boots for damage or tear.
2. Measure caliper housing inner diameter.
Item
With PBR
With MANDOWear Limit
f 61.4 mm
f 61.0 mm
Standard
10 mmWear Limit
2.0 mm
Standard
f 60.4 mm
f 60.0 mm
3. Measure pad thickness.
Notice
Always change the all pads on one wheel at a time.
5. Check the rotor disc for score or runout.
Standard
24 mmWear Limit
22 mm

4E-2 REAR DISC BRAKES
1 Rear Brake Disc Assembly
2 Brake Pad
3 Brake Caliper
4 Gasket ................................................... Replace
5 Bolt........................................................... 20 Nm
6 Gasket ................................................... Replace
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
REAR DISC BRAKE
Preceding Work : Removal of wheels and tires
7 Brake Hose
8 Gasket ................................................... Replace
9 Eye-hose Bolt......................................15-18 Nm
10 Washer
11 Bolt....................................................85-105 Nm

REAR DISC BRAKES 4E-3
Tightening Torque 15 - 18 Nm
Tightening Torque 85 - 105 Nm
Removal & Installation Procedure
1. Remove the eye-hose bolt and disconnect the hose.
Installation Notice
2. Unscrew the mounting bolts and remove the brake caliper
assembly.
Installation Notice
3. Pull out the brake pads. Replace pads if necessary.
Notice
Always change the all pads on one wheel at a time.
4. Installation should follow the removal precedure in the
reverse order.
5. Bleed the air from the system.

4E-4 REAR DISC BRAKES
Standard
10.4 mmWear Limit
9.3 mm
UNIT REPAIR
REAR DISC BRAKE
Inspection Procedure
1. Clean all components and visually check the followings.
lCheck the cylinder and piston for wear, rust or damage.
lCheck the caliper body and guide pin for wear, damage
or crank.
lCheck the pads for uneven wear or oiliness.
lCheck the boots for damage or tear.
Standard
f40.5 mm
f38.2 mmWear Limit
f41.5 mm
f39.2 mm
2. Measure caliper housing inner diameter.
3. Measure pad thickness.
Standard
9.5 mmWear Limit
2.0 mm
Notice
Always change the all pads on one wheel at a time.
4. Measure rotor disc thickness.
5. Check the rotor disc for score or runout.
Item
With PBR
With MANDO

Front
Rear
Front
Rear
SECTION 4F
ANTILOCK BRAKE SYSTEM
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this
cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Model
ECUNumber of Pins
Operating Temperature
Motor Operating Current
Solenoid Coil Resistance
External Resistance
Air Gap
Number of teethDescription
ABS 5.3
31
-40 ~ +120°C
Below MAX 40A
1.28KW - 1.92KW
0.35 - 1.60 mm
0.15 - 1.20 mm
52
52ABS/ABD 5.3
83
-40 ~ +85°C
Below MAX 45A
8.04 - 9.04W except AV,
HSV 4.04 - 4.54W
1.28KW - 1.92KW
0.35 - 1.60 mm
0.15 - 1.20 mm
52
52 Hydraulic System
Wheel Speed Sensor
Impulse Ring
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4F-1
General Specifications . . . . . . . . . . . . . . . . . . 4F-1
Schematic and Routing Diagrams . . . . . . . . 4F-2
ABS 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-2
ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-3
ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-4
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-5
Component Locator . . . . . . . . . . . . . . . . . . . 4F-6
ABS, ABS/ABD . . . . . . . . . . . . . . . . . . . . . . . . 4F-6
ABD System Description . . . . . . . . . . . . . . . 4F-7Self Diagnosis . . . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . 4F-11
Defect Codes . . . . . . . . . . . . . . . . . . . . . . . . 4F-13
Maintenance and Repair . . . . . . . . . . . . . . 4F-19
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 4F-19
Wheel Speed Sensor . . . . . . . . . . . . . . . . . . 4F-19
Hydraulic Circuit . . . . . . . . . . . . . . . . . . . . 4F-21
ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-21
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . 4F-24

4F-6 ANTILOCK BRAKE SYSTEM
ABS,ABS/ABD
COMPONENT LOCATOR
1 ABS Hydraulic Unit
2 ABS/ABD Hydraulic Unit
3 Diagnosis Socket
4 Front Wheel Speed Sensor
5 Front Impulse Ring6 Rear Wheel Speed Sensor
7 Rear Impulse Ring
8 ABS Warning Indicator Light
9 TCS Indicator Light
1 0 ABS/ABD ECU

ANTILOCK BRAKE SYSTEM 4F-7
ABD SYSTEM DESCRIPTION
General:
The Automatic Brake Differential Lock (ABD) is a traction system by means of brake intervention only, available in
a low speed range (< 60kph).
It workes on m-split roads with sidewise different friction coefficients.
The spinning driven wheel is braked and the drive torque can be transferred to the wheel on the high- m side.
During ABD active, the ABD information lamp is blinking.
The temperature of the brakes is calculated by a mathematical model and ABD is switched passive if the calculated
temperature is greater than a threshold value(500°C).
ABD is permitted again, when the calculated temperature is less than 350°C.
Control Algorithm:
The input signals for the control algorithm are the filtered
wheel speed signals from the ABS speed processing.
With the speed difference of the driven wheels, the control
deviation is calculated.
If the control deviation exceeds a certain threshold value,
the wheel with the greater slip is braked actively.
The threshold value depends on the vehicle speed:
It is reduced with increasing vehicle speed down to a constant
value.
Pressure Modulation:
Depending on the control deviation and the wheel acceleration of the spinning wheel, pressure increase, hold and
decrease are made.
The pressure modulation is done with the conventional control with the valves. ASV, USV, EV and AV according
the the following table:
Speed Range:
ABD is available in the speed range £ 60 kph.
Above 60 kph vehicle speed, ABD is passive.
It is possible to initiate ABD operation up to a vehicle speed of 55kph.
Increase
Open Open Open ASVDecrease Hold
Closed Closed Closed
Closed Closed Open
Open Closed Closed USV
EV
AV
Speed difference driven wheels [kph]
18
6
1260ABD operation
Vehicle
speed
[kph]