change time SSANGYONG MUSSO 1998 Workshop Repair Manual

SERVICEMANUAL
FOREWORD
This manual includes procedure for mainte-
nance, adjustment, service operation and re-
moval and installation of components.
All information, illustrations and specifications
contained in this manual are based on the latest
product information available at the time of
manual approval.
The right is reserved to make changes at any
time without notice.
SECTION INDEX
DRIVE LINE/AXLE
BRAKES
TRANSMISSION
STEERING
HVAC
(HEATING, VENTILATION,
AND AIR CONDITIONING)
RESTRAINTS
BODY AND ACCESSORIES 3
4
5
6
7
8
9
ENGINE
SUSPENSION1
2 FRONT MATTER GENERAL INFORMATION0A
0B
SSANGYONG-DAEWOO
MOTOR CO., LTD. 1998
KORANDO
MUSSO

SECTION 0B
GENERAL INFORMATION
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 0B-1
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . 0B-1
Vehicle Dimensions and Weights . . . . . . . . . . 0B-5
Standard Bolt Specifications . . . . . . . . . . . . . . 0B-6
Maintenance and Repair . . . . . . . . . . . . . . . 0B-7
Maintenance and Lubrication . . . . . . . . . . . . . . 0B-7
Normal Vehicle Use . . . . . . . . . . . . . . . . . . . . . 0B-7
Explanation of Scheduled Maintenance
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0B-7
Scheduled Maintenance Charts
(Gasoline Engine) . . . . . . . . . . . . . . . . . . . . . 0B-8
Scheduled Maintenance Charts
(Diesel Engine) . . . . . . . . . . . . . . . . . . . . . . 0B-10
Owner Inspections and Services . . . . . . . 0B-12
TABLE OF CONTENTS
While Operating the Vehicle . . . . . . . . . . . . . 0B-12
At Each Fuel Fill . . . . . . . . . . . . . . . . . . . . . . 0B-12
At Least Twice A Month . . . . . . . . . . . . . . . . 0B-12
At Least Monthly . . . . . . . . . . . . . . . . . . . . . . 0B-12
At Least Twice a Year . . . . . . . . . . . . . . . . . . 0B-12
Each Time the Oil is Changed . . . . . . . . . . . 0B-13
At Least Annually . . . . . . . . . . . . . . . . . . . . . 0B-13
Recommended Fluids and Lubricants . . . . . 0B-14
General Description and System
Operation . . . . . . . . . . . . . . . . . . . . . . . . 0B-15
General Repair Instructions . . . . . . . . . . . . . 0B-15
Vehicle Identification Number System . . . . . . 0B-16
Vehicle Lifting Procedures . . . . . . . . . . . . . . 0B-19
SPECIFICATIONS
TECHNICAL DATA
Transaxle Performance
Application
Maximum Speed (Km/h)
Minimum Turning Radius (m)661LA
143
5.7662NA
145
5.7662LA
156
5.72.0L DOCH
168
5.72.3L DOCH
176
5.73.2L DOCH
190
5.7
Application
Maximum Speed (Km/h)
Minimum Turning Radius (m)
Performance-Autumatic Transaxle (MB)
2.3L DOCH
171
5.73.2L DOCH
190
5.7
Application
Maximum Speed (Km/h)
Minimum Turning Radius (m)
Performance-Autumatic Transaxle (BTRA)
661LA
143
5.7662NA
138
5.7662LA
156
5.72.3L DOCH
171
5.73.2L DOCH
188
5.7

0B-8 GENERAL INFORMATION
SCHEDULED MAINTENANCE CHARTS (GASOLINE ENGINE)
Engine
Months
MAINTENANCE
ITEMMAINTENANCE INTERVALKilometers or time in months, whichever comes first
120 105 90 75 60 45 30 15 1
96 84 72 60 48 36 24 12 - x1,000 km
Chart Symbols:
I - Inspect these items and their related parts. If necessary, correct, clean, replenish, adjust or replace.
R - Replace or change.
(1) If vehicle is operated under severe condition : short distance driving, extensive idling or driving in dusty condition. Change
engine oil and the filter every 7,500 km or 6 months, whichever comes first.
(2) More frequent maintenance is required if under dusty driving condition.
(3) Refer to “Recommended fluids and lubricants”.
Drive belt
Engine oil & filter (1) (3)
Cooling system hose & connections
Engine coolant (3)
Fuel filter (2)
Fuel line & connections
Air cleaner (2)
Ignition timing
Spark plugs
Charcoal canister & vapor linesI
I
I
I
-
I
-
-I
R
I
I
-
I
I
I
I
-I
R
I
I
-
I
I
I
R
-I
R
I
I
-
I
I
I
I
II
R
I
R
R
I
R
I
R
-I
R
I
I
-
I
I
I
-I
R
I
I
-
I
I
I
R
II
R
I
I
-
I
I
I
I
-I
R
I
R
R
I
R
I
R
-

GENERAL INFORMATION 0B-9
Chassis and Body
Months
MAINTENANCE
ITEMMAINTENANCE INTERVALKilometers or time in months, whichever comes first
120 105 90 75 60 45 30 15 1
96 84 72 60 48 36 24 12
- x1,000 km
Exhaust pipes & mountings
Brake/Clutch fluid(3)(4)
Parking brake/Brake pads F & R (5)
Brake line & connections (including booster)
Manual transmission oil (3)
Clutch & brake pedal free play
Front & Rear Differential Fluid (3)I
R
I
I
I
I
I-
-
-
I
I
-
II
I
I
I
I
I
II
R
I
I
I
I
II
I
I
I
R
I
RI
I
I
I
I
I
II
R
I
I
R
I
RI
I
I
I
I
I
II
R
I
I
I
I
I
Automatic transmission fluid (MB W4A040) (6)
Automatic transmission fluid (BTRA M74)
Chassis & underbody bolts & nuts tight/secure
Tire condition & inflation pressure
Wheel alignment (7)
Steering wheel & linkage
Power steering fluid & lines* (3)
Drive shaft boots
Seat belts, buckles & anchors
Lubricate locks, hinges & bonnet latchI
I
I
I
II
I
I
I
I
I
I
I
I
II
I
I
I
I
I
I
I
I
IR
I
I
I
I
I
I
I
II
I
I
I
I
I
I
I
II
I
I
I
I
I
I
I
I
IR
R
I
I
I
I
I
I
I
II
I
I
I
I
I
I
I
I
Transfer case fluidRIII
Inspect & ADJUST when abnormal condition is noted
I
I
I
I
I
I
I
I
I
Chart Symbols :
I - Inspect these items and their related parts. If necessary, correct, clean, replenish, adjust or replace.
R - Replace or change.
(3) Refer to “Recommended fluids and lubricants”.
(4) Change the brake / clutch fluid every 15,000 km if the vehicle is mainly driven under severe conditions:
- Driving in hilly or mountainous terrain, or
- Towing a trailer frequently
(5) More frequent maintenance is required if under severe condition : short distance driving, extensive idling, frequent low -
speed operation in stop-and-go traffic or driving in dusty condition.
(6) Change automatic transaxle fluid and filter every 75,000 km if the vehicle is mainly driven under severe conditions.
- In heavy city traffic where the outside temperature regularly reaches 32°C (90°F) or higher, or
- In hilly or mountainous terrain, or
- When doing frequent trailer towing, or
- Uses such as found in taxi, police or delivery service.
(7) If necessary, rotate and balance wheels.

0B-10 GENERAL INFORMATION
SCHEDULED MAINTENANCE CHARTS (DIESEL ENGINE)
Engine
Months
-
MAINTENANCE
ITEMMAINTENANCE INTERVAL
Kilometers or time in months, whichever comes first
100 90 80 70 60 50 40 30 20 10 1
60 54 48 42 36 30 24 18 12 6 x1,000 km
NOTE 1 :Injection Timing :
Adjust as required :
- When excessive smoke is visible (black or white)
- Poor performance/economy
Chart Symbols:
I - Inspect these items and their related parts. If necessary, correct, clean, replenish, adjust or replace.
R - Replace or change.
(1) If vehicle is operated under severe condition : short distance driving, extensive idling or driving in dusty condition, change
engine oil every 5,000km or 3 months, whichever comes first.
(2) More frequent maintenance is required if under dusty driving conditing.
(3) Refer to “Recommended fluids and lubricants”.
Drive belt
Engine oil & fillter (1) (3)
Cooling system hose & connections
Engine coolant (3)
Fuel filter (2)
Fuel line & connections
Glow plug
Pre - fuel filter
Air cleaner (2)
Ignition timing (see NOTE 1)I
R
II
R
I
I
I
I
I
R
I
I
I
I
I
I
II
R
I
I
I
R
II
R
I
R
I
I
I
I
II
R
I
I
I
I
II
R
I
R
I
I
I
R
II
R
I
I
I
I
II
R
I
I
R
I
I
II
R
I
R
I
I
R
II
R
I
I
I
I
I
I
I

GENERAL INFORMATION 0B-11
Chassis and Body
Months
-
MAINTENANCE
ITEMMAINTENANCE INTERVAL
Kilometers or time in months, whichever comes first
100 90 80 70 60 50 40 30 20 10 1
60 54 48 42 36 30 24 18 12 6 x1,000 km
Exhaust pipes & mountings
Brake/clutch fluid(3) (4)
Parking brake/Brake pads (F & R) (5)
Brake line & connections (including booster)
Manual transmission fluid (3)
Clutch & brake pedal free play
F & R Differential fluid (3)
I
II
I
I
I
I
I
II
I
I
I
I
I
II
R
I
I
I
I
II
I
I
I
I
I
II
I
I
I
R
I
RI
R
I
I
I
I
II
I
I
I
I
I
II
I
I
I
I
I
II
R
I
I
I
I
II
I
I
I
R
I
R
Automatic transmission fluid (BTRA M74) (6)
Chassis & underbody bolts & nuts tight/secure
Tire condition & inflation pressure
Wheel alignment (7)
Steering wheel & linkage
Power steering fluid & lines* (3)
Drive shaft boots
Seat belts, buckles & anchors
Lubricate locks, hinges & bonnet latchI
I
I
I
I
I
I
II
I
I
I
I
I
I
II
I
I
I
I
I
I
I
II
I
I
I
I
I
I
II
I
I
I
I
I
I
II
I
I
I
I
I
I
II
I
I
I
I
I
II
I
I
I
I
I
I
II
I
I
I
I
I
I
I
Transfer case fluid (3)R
IR
I II
I
I
I
I
II
I
I
I
I
I
I
I
I
Inspect & ADJUST when abnormal condition is noted
II
I
Chart Symbols :
I - Inspect these items and their related parts. If necessary, correct, clean, replenish, adjust or replace.
R - Replace or change.
(3) Refer to “Recommended fluids and lubricants”.
(4) Change the brake / clutch fluid more regularly if the vehicle is mainly driven under severe conditions :
- Driving in hilly or mountainous terrain, or
- Towing a trailer frequently
(5) More frequent maintenance is required if under severe condition : short distance driving, extensive idling, frequent low -
speed operation in stop-and-go traffic or driving in dusty condition.
(6) Change automatic transmission fluid every 70,000 km if the vehicle is mainly driven under severe conditions.
- In heavy city traffic where the outside temperature regularly reaches 32°C (90°F) or higher, or
- In hilly or mountainous terrain, or
- When doing frequent trailer towing, or
- Uses such as found in taxi, police or delivery service.
(7) If necessary, rotate and balance wheels.

0B-12 GENERAL INFORMATION
OWNER INSPECTIONS
AND SERVICES
WHILE OPERATING THE VEHICLE
Horn Operation
Blow the horn occasionally to make sure it works. Check
all the button locations.
Brake System Operation
Be alert for abnormal sounds, increased brake pedal
travel or repeated puling to one side when braking. Also,
if the brake warning light goes on, or flashes, something
may be wrong with part of the brake system.
Exhaust System Operation
Be alert to any changes in the sound of the system or
the smell of the fumes. These are signs that the system
may be leaking or overheating. Have the system
inspected and repaired immediately.
Tires, Wheels and Alignment Operation
Be alert to any vibration of the steering wheel or the
seats at normal highway speeds. This may mean a wheel
needs to be balanced. Also, a pull right or left on a
straight, level road may show the need for a tire pressure
adjustment or a wheel alignment.
Steering System Operation
Be alert to changes in the steering action. An inspection
is needed when the steering wheel is hard to turn or
has too much free play, or is unusual sounds are noticed
when turning or parking.
Headlight Aim
Take note of the light pattern occasionally. Adjust the
headlights if the beams seem improperly aimed.
AT EACH FUEL FILL
A fluid loss in any (except windshield washer) system
may indicate a problem. Have the system inspected and
repaired immediately.
Engine Oil Level
Check the oil level and add oil if necessary. The best
time to check the engine oil level is when the oil is warm.
1. After stopping the engine, wait a few minutes for the
oil to drain back to the oil pan.
2. Pull out the oil level indicator (dip stick).
3. Wipe it clean, and push the oil level indicator back
down all the way.
4. Pull out the oil level indicator and look at the oil level
on it.5. Add oil, if needed, to keep the oil level above the
lower mark. Avoid overfilling the engine, since this
may cause engine damage.
6. Push the indicator all the way back down into the
engine after taking the reading.
If you check the oil level when the oil is cold, do not run
the engine first. The cold oil will not drain back to the
pan fast enough to give a true oil level reading.
Engine Coolant Level and Condition
Check the coolant level in the coolant reservoir tank
and add coolant if necessary. Inspect the coolant.
Replace dirty or rusty coolant.
Windshield Washer Fluid Level
Check the washer fluid level in the reservoir. Add fluid if
necessary.
AT LEAST TWICE A MONTH
Tire And Wheel Inspection and Pressure
Check
Check the tire for abnormal wear or damage. Also check
for damaged wheels. Check the tire pressure when the
tires are cold ( check the spare also, unless it is a
stowaway). Maintain the recommended pressures. Refer
to “Tire and Wheel” is in section 0B.
AT LEAST MONTHLY
Light Operation
Check the operation of the license plate light, the
headlights (including the high beams), the parking lights,
the fog lights, the taillight, the brake lights, the turn
signals, the backup lights and the hazard warning flasher.
Fluid Leak Check
Periodically inspect the surface beneath the vehicle for
water, oil, fuel or other fluids, after the vehicle has been
parked for a while. Water dripping from the air
conditioning system after use is normal. If you notice
fuel leaks or fumes, find the cause and correct it at once.
AT LEAST TWICE A YEAR
Power Steering System Reservoir Level
Check the power steering fluid level. Keep the power
steering fluid at the proper level. Refer to
Section 6A,
Power Steering System.
Brake Master Cylinder Reservoir Level
Check the fluid and keep it at the proper level. A low
fluid level can indicate worn disc brake pads which may
need to be serviced. Check the breather hole in the
reservoir cover to be free from dirt and check for an
open passage.

GENERAL INFORMATION 0B-13
Weather-Strip Lubrication
Apply a thin film silicone grease using a clean cloth.
EACH TIME THE OIL IS CHANGED
Brake System Inspection
This inspection should be done when the wheels are
removed for rotation. Inspect the lines and the hoses
for proper hookup, binding, leaks, cracks, chafing, etc.
Inspect the disc brake pads for wear. Inspect the rotors
for surface condition. Inspect other brake parts, the
parking brake, etc., at the same time. Inspect the brakes
more often if habit or conditions result in frequent braking.
Steering, Suspension and Front Drive Axle
Boot And Seal Inspection
Inspect the front and rear suspension and the steering
system for damaged, loose or missing parts, signs of
wear or lack of lubrication. Inspect the power steering
line and the hoses for proper hookup, binding, leaks,
cracks, chafing, etc. Clean and inspect the drive axle
boot and seals for damage, tears or leakage. Replace
the seals if necessary.
Exhaust System Inspection
Inspect the complete system (including the catalytic
converter if equipped). Inspect the body near the exhaust
system. Look for broken, damaged, missing, or out-of-
position parts as well as open seams, holes, loose
connections, or other conditions which could cause heat
buildup in the floor pan or could let exhaust fumes seep
into the trunk or passenger compartment.
Throttle Linkage Inspection
Inspect the throttle linkage for interference or binding,
damaged, or missing parts. Lubricate all linkage joints
and throttle cable joints, the intermediate throttle shaft
bearing, the return spring at throttle valve assembly, and
the accelerator pedal sliding face with suitable grease.
Check the throttle cable for free movements.
Engine Drive Belts
Inspect all belts for cracks, fraying, wear and proper
tension. Adjust or replace the belts as needed.
Hood Latch Operation
When opening the hood, note the operation of the
secondary latch. It should keep the hood from opening
all the way when the primary latch is released. The hood
must close firmly.
AT LEAST ANNUALLY
Lap and Shoulder Belts Condition and
Operation
Inspect the belt system including: the webbing, the
buckles, the latch plates, the retractor, the guide loops
and the anchors.
Movable Head Restraint Operation
On vehicles with movable head restraints, the restraints
must stay in the desired position.
Spare Tire and Jack Storage
Be alert to rattles in the rear of the vehicle. The spare
tire, all the jacking equipment, and the tools must be
securely stowed at all times. Oil the jack ratchet or the
screw mechanism after each use.
Key Lock Service
Lubricate the key lock cylinder.
Body Lubrication Service
Lubricate all the body door hinges including the hood,
the fuel door, the rear compartment hinges and the
latches, the glove box and the console doors, and any
folding seat hardware.
Underbody Flushing
Flushing the underbody will remove any corrosive
materials used for ice and snow removal and dust control.
At least every spring clean the underbody. First, loosen
the sediment packed in closed areas of the vehicle. Then
flush the underbody with plain water.
Engine Cooling System
Inspect the coolant and freeze protection fluid. If the fluid
is dirty or rusty, drain, flush and refill the engine cooling
system with new coolant. Keep the coolant at the proper
mixture in order to ensure proper freeze protection,
corrosion protection and engine operating temperature.
Inspect the hoses. Replace the cracked, swollen, or
deteriorated hoses. Tighten the clamps. Clean the
outside of the radiator and the air conditioning
condenser. Wash the filler cap and the neck. Pressure
test the cooling system and the cap in order to help
ensure proper operation.

M162 ENGINE CONTROLS 1F1-23
Failure
codeItemChecking method Te s t
stepRequirementSpecified
valuePossible cause
106 11The value will
be changed in
1.2 - 1.7 V - Voltage
(alternating)
0.9 - 1.6 W 71 11
71 72
· Engine:in cranking
Þ 7.1
· Ignition:ON
- Remove the
connector from the
Camshaft position
sensor between
No.1 terminal and
No.3 terminal. 1311 -14 V· ·· ·
· Camshaft
position
sensor
(E23 only)
- Power
supply· Cable
· OVPR
· ·· ·
· Ignition
coil(T1/1)
- primary coil
voltage
(No.2 and 5
cylinder)· Engine:in cranking
(starter operating)
- Measuring range:
400 V
- Time range: 100 %
(using engine tester)
· Ignition:OFF200 - 350 V
Camshaft position
sensor
64,Þ 8.0· Þ 8.1
Þ 8.1
· ·· ·
· Connecting
resistance of
ignition coil
between T1/
1 and T1/2· Cable
· Ignition coil T1/1
· Ignition coil T1/2
72 11
· ·· ·
· Ignition
coil(T1/2)
- primary coil
voltage
(No.3 and 4
cylinder)· Engine:in cranking
(starter operating)
- Measuring range:
400 V
- Time range: 100 %
(using engine tester)200 - 350 V 65,Þ 9.0· Þ 9.1
0.9 - 1.6 W
72 71
· Ignition:OFFÞ 9.1· ·· ·
· Connecting
resistance of
ignition coil
between T1/
2 and T1/1· Cable
· Ignition coil T1/1
· Ignition coil T1/2 The
resistance of
ignition coil at
20°C is
approached
0.6W
The
resistance of
ignition coil at
20°C is
approached
0.6W

1F1-48 M162 ENGINE CONTROLS
A . Valves Closed
B. Valves Opened
The pressure difference between the fuel pressure and the
intake manifold is about 3.8 bars during the full load.

The spring chamber(9) is connected to the intake manifold
with the vacuum hose at the intake pipe connection(7). The
negative pressure generated in the intake manifold activates
the diaphragm, and thus the fuel pressure gets reduced to the
rate of the operating extent of the diaphragm by the intake
manifold's negative pressure.
Consequently, the fuel pressure in the fuel distributor changes
by the intake manifold's negative pressure, and the injector's
fuel pressure gets reduced independently to the throttle valve's
position. Thus, the fuel injection volume can only be determined
according to the injector's injecting duration.
2. Fuel return line
3. Valve
5. Diaphragm
6. Compression Spring
8. Fuel Chamber
9. Spring Chamber
1. Fuel Pressure Regulator
2. Intake Manifold
3. Fuel Return(to fuel tank)
4. Fuel Supply(form fuel pump)
5. Fuel Pressure(approx. 3.8 bars)
6. Intake Manifold Negative Pressure(0 bar)
Function of the Fuel Pressure Regulator
The fuel pressure regulator maintains the fuel pressure in the
fuel line with the pressure of 3.2 bars to 3.8 bars according to
the intake manifold pressure. This operating pressure cannot
be changed, and the fuel injection volume will be only
determined by the injection time. Over supplied fuel returns to
the fuel tank through the return line.

There is no negative pressure applied to the spring chamber(9)
during the full load, and it is separated from the fuel chamber(8)
by the diaphragm(5).
When the fuel pressure goes up, the diaphragm forces the
compression spring(6) in the direction of compression . At this
moment, the valve(3) sticks to the diaphragm by the fuel
pressure, and the fuel return line(2) opens. The fuel over
supplied returns to the fuel tank through the return line.