161 SSANGYONG MUSSO 2003 Service Manual

1E2-10 M161 ENGINE ELECTRICAL Ignition Cable and Cable Lay-out
1. Firing Order : 1-3-4-2
2. T1/1 : Connect the cylinder 1 + 4
3. T1/2 : Connect the cylinder 2 + 3
Removal & Installation Procedure
1. Disconnect the battery negative cable.
2. Unscrew the 3 screws and remove the ignition cable ductcover. Installation Notice
3. Seperate the cable from the ignition cable and the spark plug.
4. Remove the 2 bolts from each ignition cable and remove the ignition cables. Installation Notice Install the ignition cable to the cylinder 2 and 4 and connect the cable from 1 to 4, and from 2 to 3. - T1/1 : Cylinder 1 and 4- T1/2 : Cylinder 2 and 3
5. Installation should follow the removal procedure in the reverse order.
Tightening Torque 9 - 11 Nm
Tightening Torque 9 - 11 Nm

M161 ENGINE ELECTRICAL 1E2-11
Inspection & Maintenance (for E2.3 MSE)
1. Measure the primary resistance between the cable terminals1 and 15 after removing the ignition cable wiring connector
(1 and 15) with ignition switch OFF. Notice Replace the ignition coil if out of the specified resistance.
T1/2 : between No.71 and No.69
Notice Check the ignition cable and the ECU if out of the
specified value.
3. Measure the secondary cable resistance between the ignition coil 5a and 5b using a multimeter.
2. Measure the primary voltage(T1/1) between the ECU
terminals No.72 and No.69 during the engine cranking (starter motor activated).
Specified Value 6 - 8.5 K
Specified Value0.9 - 1.6
Specified Value 200 - 350 V

1E2-12 M161 ENGINE ELECTRICALUNIT REPAIR
BATTERY
Inspection Notice
When charging the battery, do not leave the inflammable
objects around it.
When checking the electrolyte of battery, put on
an eye protector and gloves.
1. Inspect the surface of the battery and replace if any defects were found on it.
2. Check if the specific gravity of the electrolyte is within the specified value. Notice
Replace the battery if the maximum tolerance of the
electrolyte between cells is out of the specified value.
Measure the specific gravity in the approx. 20 °C
of ambient temperature.
3. Replenish the electrolyte if necessary. Battery Capacity(Ah)Battery Specific Gravity
Max. Tolerance between Cells
75
1.24
0.04

1F1-8 M162 ENGINE CONTROLSCruise control acceleration failure Cruise control deceleration failureECU failure(RAM)ECU failure(EPROM) Servo motor control output inter-ruption memory failureServo motor open/shortUnprogramed ECU with Immobilizer Uncoded ECU ECU failure(NVRAM checksum failure) ECU failure(coding ID checksum failure)ECU failure(coding checksum failure)ECU failure(programing checkusm failure)ABD input signal short(power) ABD input signal short(GND) Low pedal valve sensor SP1 voltageHigh pedal valve sensor SP1 voltageLow pedal valve sensor SP2 voltageHigh pedal valve sensor SP2 voltageDifferent pedal valve sensor signal(1,2) Pedal valve sensor 1,2 failure
HFM sensor, and throttle position sensorfailureECU failure(incompatible CPU)ECU failure(CPUs communication failure) ECU failure(CPU(2) configuration failure) ECU failure(CPU(2) fault)ECU failure(CPU run time failure betweenCPUs)No.5 injector short(PWR)
93969798 99
100 101 102 103 104 105108 109 11 0
11 6
11 7
11 9
120 121 122123125126 127 129130131132 Short learning control failureLambda control failure (rich stop)Lambda control failure (lean stop) Lambda idle adaptation failure(above rich threshold) Lambda idle adaptation failure(below lean threshold)learning control failure(rich, low load)learning control failure(lean, low load) learning control failure(rich, high load) learning control failure(lean, high load)Low throttle position sensor(IP1) voltageHigh throttle position sensor(IP1) voltageLow throttle position sensor(IP2) voltage High throttle position sensor(IP2) voltage Throttle actuator learning data faultThrottle actuator learning control failureExceed fuel-cut safety timeThrottle valve return spring failureCruise control interruption memory failure Throttle actuator failure Pedal module position sensor signal failureDifferent HFM signal with throttle potentiometerBoth throttle potentiometer(IP1&IP2) failureIPS1 with IPS2 High permanent throttle signal Message counter failure
cruise control ’OFF ’
Vehicle speed signal failure
Vehicle speed signal failureCruise control lever failure 133134 136 137 139 140 141142 143 144145146150 151 160161162163164 167 185 186 187 188 189190 192
Failure
code DescriptionFailure
code Description

1F1-26 M162 ENGINE CONTROLS
IDLING CONTROL AND ELECTRONIC PEDAL SYSTEM TEST
2.1 
Ignition:ON
50 51 2.25 - 2.75 V



Pedal valve
sensor: - Power supply
(potentiometer 2)
Cable
 ECU
Failure
code Item

1.0
Checking method
 Ignition:ON
 Position of
accelerator pedal: - Closed throttle position
- Full throttle with kick down
Test
stepRequirement
Specified value Possible cause
31 47 0.3 - 0.7 V



Pedal valve
sensor: - Signal
(potentiometer 1)
160, 161,164,167,
4.3 - 4.8 V 
1.1
 Cable
 Pedal valve sensor
1.1 
Ignition:ON
31 32 4.75 - 5.25 V



Pedal valve
sensor: - Power supply
(potentiometer 1)

Cable
 ECU
2.0 
Ignition:ON
 Position of
accelerator pedal: - Closed throttle position
- Full throttle with kick down
50 48
0.1 - 0.4 V



Pedal valve
sensor:- Signal
(potentiometer 2)
162, 163,164,167,
2.1 - 2.5 V
2.1
 Cable
 Pedal valve sensor
3.0 
Engine:in idling
84 87 0.3 - 0.9 V



Throttle
valveactuator:- SignalThrottle valve
potentiometer 1
104, 105,108,109,116,119,185,
4.0 - 4.6 V
3.1
 Cable
 E-GAS actuator
 Position of
accelerator pedal:- Closed throttle position
- Full throttle with kick down

M162 ENGINE CONTROLS 1F1-37
Pin No.Abbreciation
Description
1 23456789
10 11
121314151617181920 -
TM.50 --
GND ---
LSH1
TM.31TM.87TM.30
WFS I/O WFS O -
GND LS1 ---
-Starter motor TM.50--Electronic ground---Lambda probe 1 heatingPower ground TM.31
V-BATTERY TM.87
V-BATTERY TM.30Immobilizer crypto readImmobilizer crypto write-Lambda probe 1 groundLambda probe 1 signal---
ECU Pin Numbers and Descriptions
Vehicle Connector

M162 ENGINE CONTROLS 1F1-41
Application
Pin No.Description
- Starter motor TM.50- - Electronic ground--- Lambda probe 1 heating Power ground TM.31
V-BATTERY TM.87
V-BATTERY TM.30Immobilizer crypto read Immobilizer crypto write -Lambda probe 1 groundLambda probe 1 signal- - -Brake switch-- - --Air conditioning clutch relay- - -1 23 4 5678 9
10 11
12 13 14 15161718 19 20212223 24 25262728 29 30-
TM.50 - -
GND - --
LSH1
TM.31TM.87TM.30
WFS I/O WFS O
-
GND LS1 - - -
BRS -- - --
KLIKU - - - -
--
-- -





-

- - -
-- - --
- - - -
- -
- --






-

- - -
-- - --
- - -
: Standard, : Option Remarks
Abbreviation E32 ENG,
5speed M/T
E32 ENG,
4speed A/T (BTRA)

SECTION 1G2
M161 ENGINE INTAKE & EXHAUST
TABLE OF CONTENTSSPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
N m
9 - 11
22.5 - 27.5 22.5 - 27.5 9.5 - 12.5 15 - 28 28 - 47
Application
Air Cleaner Housing Cover NutIntake Manifold Bolt (M8 x 20) Intake Manifold Bolt (M8)Exhaust Mainfold Stud BoltExhaust Pipe Nut (Engine) Exhaust Pipe Bolt
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1G2-1 Fastener Tightening Specifications . . . . . . . . 1G2-1
Maintenance and Repair . . . . . . . . . . . . . . 1G2-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1G2-2
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 1G2-2Air Intake Shield . . . . . . . . . . . . . . . . . . . . . .
1G2-4
Intake Air Duct . . . . . . . . . . . . . . . . . . . . . . . 1G2-5
Intake Manifold . . . . . . . . . . . . . . . . . . . . . . . 1G2-7
Exhaust Manifold . . . . . . . . . . . . . . . . . . . . . 1G2-9

1G2-2 M161 ENGINE INTAKE & EXHAUSTMAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
AIR CLEANER
1 Air Cleaner Assembly
2 Element Assembly
3 Insulator
4 Air Duct Hose5 Air Inlet Duct
6 Bolt (M8 × 30 ) ................................... 22.5-27.5 Nm
7 Bolt (M6 × 35 ) ........................................... 9-11 Nm

M161 ENGINE INTAKE & EXHAUST 1G2-3
Removal & Installation Procedure1. Release the clamp securing HFM sensor and air cleaner.
2. Disengage the air cleaner assembly and HFM sensor assembly.
3. Unserew the mounting bolt(6) from the bracket.
Installation Notice
Tightening Torque 22.5 - 27.5 Nm
4. Release the clamp from air cleaner assembly housing and remove the cover.
5. Remove the air cleaner assembly.
6. Remove the air cleaner housing from insulator.
Notice
Make sure the air cleaner to be seated in insulator.
7. Disengage the air duct hose and air cleaner housing and remove the housing.
8. Remove the air duct hose.
9. Unscrew the two bolts(7) from air inlet duct. Installation Notice
10. Remove the air inlet duct.
11. Installation should follow the removal procedure in the reverse order.
Tightening Torque 8 - 9 Nm