oil SSANGYONG MUSSO 2003 Service Manual

5B-18 MANUAL TRANSMISSION
8. Remove the counter shaft thrust race and bearing.
9. Carefully remove the oiling funnel from the end of thecounter shaft.
10. Using a 10 mm wrench, remove the 10 bolts from the shift cover. Notice
For assembly, note the location of the two bolts.
11. Lift up the shift cover after sliding it toward the drain plug about 3 cm. At this time remove sealer bond.
12. Using a needle nose pliers, remove the 5-R lever clip.

5B-24 MANUAL TRANSMISSION
7. Install the counter shaft rear bearing outer race, shim andretainer.
Tightening Torque 39 - 52 Nm
Using a punch and hammer, bend the lock tabs on the
retainer.
8. Install the following parts : Install the main shaft into case.
Install the main shaft rear bearing outer race into the
rear of the case.
Install the 4th speed blocking ring onto the front of the
main shaft.
Install the input shaft onto the front of the main shaft.
Install the input bearing retainer without shim onto the
front of the case.
Using a torque wrench, tighten the 4 bolts.
9. Install the 5th speed drive gear and blocking ring on the counter shaft.
10. Install the 5th synchronizer and rail/fork.
11. Install the 5th synchronizer snap ring and oiling funnel.
12. Align the slots of the lever with the rollers of the reverse fork and 5th shift rail. Apply sealer on the 5-R lever pivot bolt and install it into the case.
Tightening Torque 28 Nm
13. Using a needle nose pliers, install the 5-R lever clip.

Type Clutch Pedal Clutch Disc Clutch Master Cylinder Clutch Release Cylinder Clutch FluidDescription
Hydraulic
Suspended 158 mm
5 - 10 mm
Single Dry Diaphragm
9.85 - 10.2 mm 9.2 mm
19.8 mm
15.87 mm
14.0 mm
17.46 mm
SAE J1703 / DOT3
SECTION 5C
CLUTCH
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 5C-1 General Specifications . . . . . . . . . . . . . . . . . . 5C-1
Fastener Tightening Specifications . . . . . . . . . 5C-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . . 5C-3 Special Tools Table . . . . . . . . . . . . . . . . . . . . . 5C-3
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 5C-4 Clutch Slips . . . . . . . . . . . . . . . . . . . . . . . . . . . 5C-4
Poor Disengagement . . . . . . . . . . . . . . . . . . . 5C-4
Hard to Shift or Will not Shift . . . . . . . . . . . . . . 5C-4
Clutch Chatters When Starting . . . . . . . . . . . . 5C-4
Difficult Pedal Operation . . . . . . . . . . . . . . . . . 5C-5
SPECIFICATIONS
GENERAL SPECIFICATIONS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting thiscable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCKunless otherwise noted.
Application
Type Max. Pedal StrokePedal Free Play
TypeThickness of Disc Stroke Inner DiameterStrokeInner DiameterFree
With Load
Clutch Noisy . . . . . . . . . . . . . . . . . . . . . . . . . . 5C-5
Component Locator . . . . . . . . . . . . . . . . . . . 5C-6 Clutch Assembly . . . . . . . . . . . . . . . . . . . . . . . 5C-6
Pedal and Master Cylinder . . . . . . . . . . . . . . . 5C-7
Maintenance and Repair . . . . . . . . . . . . . . . 5C-8
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 5C-8
Bleeding of Clutch System . . . . . . . . . . . . . . . 5C-8
Clutch Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 5C-9
Master Cylinder . . . . . . . . . . . . . . . . . . . . . . 5C-13
Clutch Pedal . . . . . . . . . . . . . . . . . . . . . . . . . 5C-15
Clutch Oil Chamber . . . . . . . . . . . . . . . . . . . 5C-17

5C-4 CLUTCHChecks
Oily Facing Hard or Faulty Facing
Burnt Torsion Spring Faulty Pressure Plate Bent Clutch Diaphragm SpringHard or Bent FlywheelEngine Mounts Loose or Burnt Lever Action
Adjust Pedal Freeplay
Repair Release Cylinder Repair or Replace
Repair as Necessary Replace
Checks
Excessive Clutch Pedal Free play Faulty Clutch Release Cylinder Worn Disc, Excessive Run-out, Damaged LiningDirty or Burred Splines on Input Shaft or Clutch DiscDamaged Clutch Pressure Plate Checks
Vibration or Excessive Run-out of DiscRust or Wear of Disc Spline Oily Facing Damaged Diaphragm SpringExcessive Clutch Pedal Free play DIAGNOSIS
CLUTCH SLIPS
Checks
Excessive Wear of Facing Hard or Oily FacingDamaged Pressure Plate or FlywheelDamaged or Burnt Diaphragm SpringClutch Pedal Free play Insufficient Faulty Operation of Clutch Pedal Worn or Damaged Clutch Disc Action
Replace
Repair or Replace ReplaceReplaceAdjust
Repair or Replace Replace
POOR DISENGAGEMENT
Action
Replace
Repair or Replace Repair or Replace Replace
Adjust
HARD TO SHIFT OR WILL NOT SHIFT
CLUTCH CHATTERS WHEN STARTING
Action
Repair or Replace
Replace Replace Replace Replace
Repair or Replace
Tighten or Replace

CLUTCH 5C-7
PEDAL AND MASTER CYLINDER
1 Clutch Pedal
2 Clutch Master Cylinder
3 Clutch Tube
4 Clutch Oil Chamber5 Clutch Tube
6 Clutch Hose
7 Clutch Release Cylinder

CLUTCH 5C-11
5. Unscrew the bolts and remove the clutch cover, pressure
plate and clutch disc. NoticeBe careful not to drop the pressure plate and clutch disc.Installation Notice
Tightening Torque 21 - 27 Nm
6. Installation should follow the removal procedure in the reverse order. Notice
Before installation, clean oil and grease on the flywheel surface.
Do not clean the clutch disc and release bearing insolvent.

5C-12 CLUTCH
Inspection Procedure
1. Clutch Cover Check the diaphragm spring tip for wear and height
unevenness.
Check the pressure plate surface for wear, crack and
discoloration.
Check the strap plate rivet for looseness and replace
the clutch cover if loosened.
Unevenness Limit 0.8 mm
2. Clutch Disc Check the facing for rivet looseness, excessive runout,
sticks, oil and grease.
Measure the rivet head depth. If out limit, replace the disc.
3. Clutch Release Bearing The release bearing is permanently lubricated and
requires no cleaning.
Check the bearing for sticks, damage, abnormal noise,
turning drag and wear.
4. Release Fork If there is abnormal wear in contact point with bearing,
replace the release fork.
Wear Limit 0.3 mm

CLUTCH 5C-13
MASTER CYLINDER
1 Snap Pin
2 Clevis Pin
3 Clevis
4 Lock Nut
5 Flange Nut ........................................... 30-40 Nm
6 Push Rod
7 Cylinder Body
8 Oil Pipe ................................................ 15-18 Nm 9 Clamp
10 Reservoir
11 Spring
12 Piston Assembly
13 Boot
14 Plate
15 Snap Ring
Notice Do not disassemble the No.12.

CLUTCH 5C-17
CLUTCH OIL CHAMBER
1 Clutch Master Cylinder
2 Hydraulic Tube
3 Bolt 4 Clutch Oil Chamber
5 Hydraulic Tube
6 Clutch Release Cylinder
Notice
Installation should follow the removal procedure in the reverse order.
When installing, perform the bleeding procedures from chamber cylinder and release cylinder.

Model
TypeGear Ratio Oil Manufacturer WeightPart-Time 4408 (E)
E.S.O.F. Type
1 : 1
2.48 : 1
ATF S-3, S-4 or DEXRON II, III
1.2 L
Check : Every 15,000 km
Replace : Every 50,000 km Borg Warner30 kg
SECTION 5D1
TRANSFER CASE (PART TIME 4408)
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting thiscable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCKunless otherwise noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 5D1-1
General Specifications . . . . . . . . . . . . . . . . . 5D1-1
Schematic and Routing Diagram . . . . . . . . 5D1-2 Part Time Transfer Case - 4408 . . . . . . . . . . 5D1-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 5D1-3
Self-Diagnosis . . . . . . . . . . . . . . . . . . . . . . 5D1-4 System Description . . . . . . . . . . . . . . . . . . . . 5D1-4
Self-Diagnosis Test . . . . . . . . . . . . . . . . . . . . 5D1-8Diagnostic Diagram . . . . . . . . . . . . . . . . . . .
5D1-9
Maintenance and Repair . . . . . . . . . . . . . 5D1-10
On-Vehicle Service . . . . . . . . . . . . . . . . . . . 5D1-10
Maintenance of Transfer Case Lubricant . . 5D1-10
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 5D1-11
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . 5D1-14
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 5D1-14
Transfer Case Control Unit (TCCU) . . . . . . 5D1-36
High LowSpecification Capacity Lubrication
Application
Description