ECU SSANGYONG MUSSO 2003 Owner's Guide

1F1-24 M162 ENGINE CONTROLS
Failurecode ItemChecking method
Test
stepRequirementSpecified
value Possible cause
8 - 20 KV



Ignition coil
(T1/1, T1/2, T1/3)
- Secondary ignition voltage
> 10 M
117 118
 Engine:in cranking - Select the ignition
coil in order of T1/1,T1/2
- Measuring range: 20KV
- Time range:100 %
 Ignition:OFF
- Disconnect the coupling "No.2" fromECU.
12.0 


Knock
sensor 1 - Resistance (cylinder No1, 2, 3) 
Connecting
condition
 Cable
 ECU

11.0
64,65,66, Engine tester

11.1
 Ignition plug
 ECU
 High tension cable
6 - 8.5 K



Ignition coil
(T1/1, T1/2, T1/3)
- Secondary coilresistance 
Remove the high
tension cable of T1/1, T1/2, T1/3.

11.1 Ignition coil
(T1/1, T1/2, T1/3) 
Ignition coil T1/1
 Ignition coil T1/2
 Ignition coil T1/3
TM.4a TM.4b
56,
11



Ignition
coil(T1/3) - primary coil voltage(No.1 and 6cylinder) 
Engine:in cranking
(starter operating)- Measuring range: 400 V
- Time range: 100 % 200 - 350 V
66, 10.0
10.1
0.9 - 1.6
70 72
 Ignition:OFF 10.1 


Connecting
resistance of ignition coilbetween T1/3 and T1/2 
Cable
 Ignition coil T1/3
 Ignition coil T1/2
> 10 M
114 115 Ignition:OFF
- Disconnect the coupling "No.2" from ECU. 13.0 


Knock
sensor 2 - Resistance (cylinder No.4, 5, 6) 
Connecting
condition
 Cable
 ECU
57,
The
resistance of
ignition coil at 20°C is
approached 0.6

1F1-26 M162 ENGINE CONTROLS
IDLING CONTROL AND ELECTRONIC PEDAL SYSTEM TEST
2.1 
Ignition:ON
50 51 2.25 - 2.75 V



Pedal valve
sensor: - Power supply
(potentiometer 2)
Cable
 ECU
Failure
code Item

1.0
Checking method
 Ignition:ON
 Position of
accelerator pedal: - Closed throttle position
- Full throttle with kick down
Test
stepRequirement
Specified value Possible cause
31 47 0.3 - 0.7 V



Pedal valve
sensor: - Signal
(potentiometer 1)
160, 161,164,167,
4.3 - 4.8 V 
1.1
 Cable
 Pedal valve sensor
1.1 
Ignition:ON
31 32 4.75 - 5.25 V



Pedal valve
sensor: - Power supply
(potentiometer 1)

Cable
 ECU
2.0 
Ignition:ON
 Position of
accelerator pedal: - Closed throttle position
- Full throttle with kick down
50 48
0.1 - 0.4 V



Pedal valve
sensor:- Signal
(potentiometer 2)
162, 163,164,167,
2.1 - 2.5 V
2.1
 Cable
 Pedal valve sensor
3.0 
Engine:in idling
84 87 0.3 - 0.9 V



Throttle
valveactuator:- SignalThrottle valve
potentiometer 1
104, 105,108,109,116,119,185,
4.0 - 4.6 V
3.1
 Cable
 E-GAS actuator
 Position of
accelerator pedal:- Closed throttle position
- Full throttle with kick down

M162 ENGINE CONTROLS 1F1-27
Failurecode ItemChecking method
Test
stepRequirementSpecified
value Possible cause
3.1 
Ignition:ON
84 112 4.75 - 5.25 V



Throttle
valve actuator:- Power supply(5V)
 Cable
 ECU
4.0 
Ignition:ON
68 67 0.8 - 2.3 V
The value will
be changed in 1.0 - 2.5V.



Throttle
valve actuator:- Signal Throttle valve actuatormotor voltagesupply
104, 105,108,109,116,119,185, 
ECU
 Cable
 E-GAS actuator

Engine:in idling
- Coolant temperature:
>70 °C
84 85
4.0 - 4.6 V
Throttle valve
potentiometer 2
0.3 - 0.9 V

Position of
accelerator pedal: - Closed throttle position
- Full throttle with kick down
Throttle valvepotentiometer1+2
 Ignition:OFF
< 10
Throttle valve actuatormotorresistance 68 67

1F1-28 M162 ENGINE CONTROLS
AIR CONDITIONER CONTROL SYSTEM TEST
2.0 
Engine:In idling
 Air conditioner
switch : ON/OFF Air conditionerswitch : OFFAir conditionerswitch : ONCoolant temperature:above 105 °C
10 35
11 - 14 V 11 - 14 V
< 1 V



Condenser
fan(HI) control: Condenser fan
relay
 Fan motor
 ECU
Failure
code Item

1.0
Checking method
 Engine:In idling
 Air conditioner
switch : ON/OFF
Air conditioner switch : OFFAir conditionerswitch : ON
Te s t
stepRequirement
Specified value Possible cause
10 44 < 1 V



Air
conditioner signal:- Input signal (input signalfrom thermoamplifier)
44, 45,
11 - 14 V
5.1
 Cable
 Thermo amp
 Auto amp
 Dual pressure
switch
 Air conditioner
control panel
1.1 
Engine:In idling
 Air conditioner
switch : ON/OFFAir conditionerswitch : OFFAir conditionerswitch:ON
10 27
< 1 V



Air
conditionercompressor:- Output signal
11 - 14 V 
Thermo amp
 Auto amp
 Dual pressure
switch
 Air conditioner
control panel
 ECU

M162 ENGINE CONTROLS 1F1-31
FUEL PUMP TEST Preparation
1 ECU
2 Test Coupling(No.1-60)
3 Test Coupling(No.61-120)
4 Stop Watch
5 Measuring Beaker
Connection of the Equipment
1. Turn the ignition switch to "OFF" position. 2. Connect the test box to the ECU. 0 3 Test Box
04 ECU Test Cable
Tools Required
103 589 00 21 00 Pressure Tester 210 589 00 99 00 Adaptor Line
129 589 00 21 00 Test Box
210 589 08 63 00 Ecu Test Cable

M162 ENGINE CONTROLS 1F1-33
Connection of the Equipment
1. Connect the test box to the ECU as shown in the figure.
2. Remove the 2-pin coupling from injector.
3. Remove the fuel distributor and injector with a unit. At thistime, do not remove the supply and return line.
4. Connect the shop made cable to the injector with a firing order.
5. Collect the fuel from injector.
INJECTOR TEST
1 ECU
2 Test Coupling(No.1-60)
3 Test Coupling(No.61-120)
4 Measuring Beaker
5 Shop Made Cable
Preparation
0 3 Test Box
04 ECU Test Cable
Tools Required
129 589 00 21 00 Test Box
210 589 08 63 00 Ecu Test Cable

M162 ENGINE CONTROLS 1F1-35
MAINTENANCE AND REPAIRON-VEHICLE SERVICE
ECU Appearance
1 Cover
2 Plate
3 Connector
4 Flat Pin Vehicle Side : No. 1 - 12 Engine Side : No. 61 - 72 5 Pin
Vehicle Side : No. 13 - 60Engine Side : No. 73 - 120
A Vehicle Side Connector : Black
B Engine Side Connector : Gray

1F1-36 M162 ENGINE CONTROLS
Location Engine ECU is located at the inside of cowl side trim in right bottom of instrument panel of passenger side. Removal & Installation Procedure
1. Turn the ignition switch to "OFF" position.
2. Disconnect the battery negative cable
3. Remove the cowl side trim form passenger side.
4. Unscrew four securing nuts for ECU from mounting bracket.Installation Notice
5. Pulling out the ECU from bracket.
6. Disconnect the vehicle side coupling(B).
7. Installation should follow the removal procedure in the reverse order.
Tightening Torque 9 - 11 Nm

M162 ENGINE CONTROLS 1F1-37
Pin No.Abbreciation
Description
1 23456789
10 11
121314151617181920 -
TM.50 --
GND ---
LSH1
TM.31TM.87TM.30
WFS I/O WFS O -
GND LS1 ---
-Starter motor TM.50--Electronic ground---Lambda probe 1 heatingPower ground TM.31
V-BATTERY TM.87
V-BATTERY TM.30Immobilizer crypto readImmobilizer crypto write-Lambda probe 1 groundLambda probe 1 signal---
ECU Pin Numbers and Descriptions
Vehicle Connector

M162 ENGINE CONTROLS 1F1-45
Removal & Installation Procedure
when removing the ECU only
1. Turn the ignition switch to "OFF" position.
2. Disconnect the negative battery cable.
3. Disconnect the couplings from ECU.
4. Unscrew the left and right bolt (3) on bolt (1) and auxiliarly bracket and remove the auxiliarly bracket from the bracket assembly (2). Installation Notice
5. Unscrew the four bolts (5) and disconnect the ECU (6) from the bracket assenbly. Installation Notice
6. Installation should follow the removal procedure in the reverse order.
Tightening Torque 6 - 8 Nm
5 - 7 Nm(1) (3)
Tightening Torque 5 - 7 Nm
8. Unscrew the bolts (5) and disconnect the ECU (6) from the bracket assenbly. Installation Notice

When Removing the ECU with ABS or ABS/ASR Unit
1. Turn the ignition switch to "OFF" position.
2. Disconnect the negative battery cable.
3. Disconnect the couplings from ECU.
4. Disconnect the coupling from ABS or ABS/ASR unit.
5. Unscrew the bolt (1) and the left and right flange nuts.
6. Remove the ECU with ABS or ABS/ASR unit assembly.
7. Unscrew the left and right bolt (3) on the auxiliary bracket and remove the auxiliary bracket from the bracket assembly. Installation Notice
Tightening Torque 6 - 8 Nm
Tightening Torque 5 - 7 Nm
Tightening Torque 5 - 7 Nm
9. Installation should follow the removal procedure in the reverse order.