SSANGYONG MUSSO 2003 Service Manual

1D3-8 OM600 ENGINE COOLING COOLANT PUMP HOUSING Preceding Work : Removal of coolant pump Removal of thermostat Removal of alternator
1 Gasket ................................................... Replace
2 Coolant Pump Housing
3 Connector
4 Bolt........................................................... 10 Nm 5 Coolant Hose
6 Return Pipe
7 O-Ring
8 Temperature Sensor
Notice The bolt on the arrow should be installed last.

OM600 ENGINE COOLING 1D3-9
Removal & Installation Procedure
1. Disconnect the connector(3).
2. Separate the coolant hose (5) and return pipe(6).
3. Remove the bolts(4) evenly.Installation Notice
Tightening Torque 10 Nm
Notice Clean gasket residues on the sealing surface of coolant pump and replace the gasket.
4. Remove the coolant pump housing(2).
5. Installation should follow the removal procedure in the reverse order.

1D3-10 OM600 ENGINE COOLING COOLING FAN CLUTCH
1 Belt Pulley
2 Cooling Fan Clutch
3 Cooling Fan4 Socket Bolt
................................................ 45 Nm
5 Socket Bolt ................................................ 10 Nm
Tools Required 603 589 00 40 00 Counter Holder

OM600 ENGINE COOLING 1D3-11
Removal & Installation Procedure
1. Hold the bolt pulley with counter holder and remove thebolt(4).
Counter Holder 603 589 00 40 00
Installation Notice
Tightening Torque 45 Nm
2. Remove the socket bolt(5) and then remove the cooling fan(3) and fan clutch(2). Notice
Keep the fan clutch vertically. Installation Notice
Tightening Torque 10 Nm
3. Installation should follow the removal procedure in the reverse order.

1D3-12 OM600 ENGINE COOLING
RADIATOR Preceding : Removal of cooling fan shroud
1 Radiator Inlet Hose...............OM662LA : 220mm
............................................. OM661LA : 321mm
2 Radiator outlet Hose
3 Radiator Deaeration Tube & Hose
4 Clamp 5 Spring Clamp
6 Bolt
.......................................................... 3-7 Nm
7 Radiator
8 Spring Clamp
9 Bolt ........................................................... 3-7Nm

OM600 ENGINE COOLING 1D3-13
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermoswich connector from radiator.
3. Remove the each coolant hose.
4. Remove the auto T/M oil cooling hose and cooling line.Installation Notice
5. Loosen the radiator upper mounting bolt and remove the mounting stopper and insulator.
6. Remove the radiator.
7. Check the radiator pin for crack, leakage and bending and replace it if necessany.
8. Installation should follow the removal procedure in the reverse order.
Tightening Torque Hose : 29 - 40Nm

1D3-14 OM600 ENGINE COOLING
COOLING SUB-SYSTEM
1 Radiator
2 Cooling Fan Shroud
3 Bolt.......................................................... 3-7Nm
4 Cooling Fan Shroud
5 Radiator Deaieration Hose 7 Mounting Bracket
8 Make-up Cooling Hose
9 Bolt
........................................................... 3-7Nm
10 Cooling Reservoir-tank Cap 11 Cooling Reservoir-tank

OM600 ENGINE COOLING 1D3-15
Removal & Installation Procedure Cooling Fan Shroud
1. Remove the radiator deaeration hose and tube.Installation Notice
Tightening Torque 3 - 7 Nm
Tightening torque 3-7Nm
2. Check the shroud.
3. Installation should follow the removal procedure in the reverse order.
Coolant Sub-Tank
1. Drain the coolant from radiator.
2. Remove the each hose.
3. Loosen the mounting bolt of sub-tank and remove the coolant sub-tank. Installation Notice
4. Installation should follow the removal procedure in the reverse order.
Tightening Torque 3 - 7 Nm

1D3-16 OM600 ENGINE COOLING
THERMOSTAT
1 Thermostat
2 Seal....................................................... Replace
3 Thermostat Housing Cover 4 Coolant Hose
5 Bolt
............................................................ 10Nm

OM600 ENGINE COOLING 1D3-17
Removal & Installation Procedure
1. Drain the coolant completely.
2. Disconnect the coolant hose(4) from the thermostat housingcover(3).
3. Remove the bolts(5) and then remove the thermostat(1) and housing cover(3) Installation Notice Align the groove on thermostat and the housing cover rib(arrow).
Tightening Torque 10 Nm
Notice Replace the seal(2).
4. Installation should follow the removal procedure in the reverse order.