display SSANGYONG NEW ACTYON SPORTS 2012 User Guide

04-138210-01
3) Fuel Level Gauge
The fuel level gauge displays the resistance value of the float on the fuel sender in the fuel tank
through a pointer. Note that this vehicle doesn't have a service hole for checking the fuel sender
connector in the fuel tank.
The fuel sender and its connector can be checked and replaced only when the fuel tank is
removed. The power supply and resistance value should be measured at the connector in front of
the fuel sender (refer to wiring diagram).
When the power supply and output resistance are normal, the float operation by fuel level may be
defective; if so, replace the fuel sender.
Low fuel warning lamp comes on when:
The fuel level drops to 9 L or less. The lamp goes off if the fuel level reaches 9.5 L or more.This table shows the tolerance and resistance value changes by fuel level in normal
conditions. Therefore, the differences that can be occurred by the road conditions and fuel
fluctuations are ignored.

04-14
4) Coolant Temperature Gauge
The coolant temperature gauge displays the coolant temperature with a pointer. The angle of
pointer that changes by coolant temperature is as shown below.
Measurement of coolant temperature sensor resistance
Measure the resistance between the terminal and the ground with an ohmmeter and replace if the
resistance is out of specified range.
Temperature (ºC)20 60 80 100 120
Resistance (Ω)2449Ω ± 5% 589.4kΩ ±
5%321Ω ± 5%185.7kΩ ±
5%112.9kΩ ±
5%
Voltage (V)3.615 1.910 1.259 0.819 0.536
When the resistance value by coolant temperature is within the specified range, check
thermostat, water pump, radiator related coolant circuit for normal operation. Also, check the
wiring harnesses and connectors for proper connection.

04-158210-01
Change
OrderMode LCD Display Description
1 TRIP A The maximum distance value that can be displayed is
999.9 km with increments of 0.1 km. The trip meter is
reset to 0.0 km when the value reaches above 999.9
km. When measuring a trip distance, reset the
distance value in the mode you want to use by
pressing the TRIP switch for 1 sec. or more.
2 TRIP B The maximum distance value that can be displayed is
6,213.09 mi with increments of 0.62mi. The trip meter
is reset to 0.0 km when the value reaches above
999.9 km. When measuring a trip distance, reset the
distance value in the mode you want to use by
pressing the TRIP switch for 1 sec. or more.
3 Distance
to emptyThe estimated distance that can be traveled is
calculated based on the current fuel level.
If the DTE is less than 50 km, "---" flashes on the
display.
4 Driving
timeThe driving time from resetting the value (0:00) until
now is displayed. The value displayed is accumulated
while the engine is running even if the vehicle is not
driven. The display range is 00:00 to 99:59. When
measuring the driving time, press the TRIP switch for
1 sec. or more to reset the value.
5 Average
fuel
economyThe average fuel economy from resetting the value (-
-.-) until now is displayed. The value displayed is
accumulated while the engine is running even if the
vehicle is not driven. The display range is 0.0 to 99.9
km/h. When measuring the average fuel economy,
press the TRIP switch for 1 sec. or more to reset the
value. "--.-" is displayed on the screen when
resetting. The value is reset automatically whenever
the vehicle is fuelled.
5) Description for LCD Display
LCD display
Mode Description ▶

04-16
Change
OrderMode LCD Display Description
6 Instant fuel
consumptionThe fuel range is calculated based on the distance
driven and fuel consumed every 2 seconds. If the
vehicle speed is below 10 km/h or the engine rpm
is 200 rpm or less, the instant fuel economy is not
displayed. The display range is 0.0 to 99.9 km/.
7 Brightness
adjustmentThe brightness of the illumination can be adjusted
in 6 steps by pressing the TRIP switch briefly (less
than 1 sec.). The display is changed from ILL1 to
ILL6 every time the switch is pressed. If you select
one level within the range and press and hold the
TRIP switch, the brightness level is memorized. If
there is no TRIP switch input for 5 seconds or
more, the mode is switched to TRIP A mode
automatically. When the battery is reinstalled, the
brightness level is reset to level 4.

04-18
Brightness of LCD display when turning ON/OFF tail lamp ▶
Sequen
ceLevelTail lamp OFF Tail lamp ON
Display brightness Brightness
ratioDisplay brightness Brightness
ratio
1 ILL1 25% 5%
2 ILL2 40%9%
(LCD: 12%)
3 ILL3 55%13%
(LCD: 19%)
4 ILL4 70%17%
(LCD: 26%)
5 ILL5 85%21%
(LCD: 33%)
6 ILL6 100%25%
(LCD: 40%)
Illumination conditions of LCD display when turning ON/OFF tail lamp ▶
The illumination for the LCD display comes on when turning on the tail lamp and is adjustable only
when the ignition is ON. When turning on the tail lamp switch with the ignition OFF, the tail lamp
comes on but the LCD display is not illuminated. Refer to the illustration below.
IGN ON
(Comes on regardless of whether the tail lamp
switch is turned ON or OFF)Tail lamp comes on with IGN OFF
(Tail lamp comes on but the illumination for LC
D
display is not turned on)

04-22
How to enter self-diagnosis mode ▶
Turn the ignition ON with the TRIP switch pressed.
Press and hold the TRIP switch for 5 to 10 sec. with the ignition ON.
Press and hold the TRIP switch for less than 10 sec. and then cycle the switch between ON
and OFF 5 times within 3 sec.
Confirm that the self-diagnosis mode is activated through the instrument cluster. 1.
2.
3.
4.
4. SELF-DIAGNOSIS CHECK
Self-diagnosis OFF ▶
If the engine speed increases to 396 rpm or more while the engine is cranking or the ignition key
is turned OFF in self-diagnosis mode, the self-diagnosis mode is turned OFF automatically.
Operating process ▶
Speed gauge: changes from 0 to 220 km
RPM gauge: changes from 0 to 6,000 rpm
Fuel gauge: changes from E to F
Temperature gauge: changes from C to H
Warning/Indicator lamps: All indicator/warning lamps controlled by MICOM are turned ON.
Dimming: Illuminates at the highest lighting level.
LCD display: All elements are activated. 1.
2.
3.
4.
5.
6.
7.

09-4
2. CAUTIONS
Note that the display does not show everything in the rear area. Always check nobody,
especially animals and children, is behind the vehicle when parking or reversing.
If you can not properly check the vehicle behind, get out of the vehicle and then visually
check it.
The parking aid system is just a supplemental device to help your parking.
Always keep the safety precautions.
Do not press or shock the sensors by hitting or using a high-pressure water gun while
washing, since it may damage the sensors.
If the system is in normal operating condition, a short beep sounds when the shift lever is
moved into "R" position with the ignition key "ON". -
-
-
-
-
-
The parking aid system will not work or improperly work under following cases: ▶
1. Certain obstacles that sensors can not detect
Thin and narrow objects, such as wires, ropes, chains
Cotton, sponge, clothes, snow; that absorb ultrasonic waves
Obstacles lower than the bumper (ex. drain ditch or mud puddle) -
-
-
2. Not defective but improperly working
When the sensing portion is frozen (operates normally after thawed)
When the sensing portion is covered by rain, water drops, snow or mud (operates normally
after cleaned)
When receiving other ultrasonic signals (metal sound or air braking noises from heavy
commercial vehicles)
When a high-power radio is turned on -
-
-
-
3. Narrowed sensing area
When the sensing portion is partially covered by snow or mud (operates normally after
cleaned)
<007a009c009900990096009c0095008b00900095008e0047009b008c00940097008c00990088009b009c0099008c00470096008d0047009a008c0095009a0096009900470090009a0047009b009600960047008f0090008e008f0047004f00880097009700
990096009f005500470096009d008c00990047005f005700b6>C) or too low (approx.
below -30°C) -
-
When driving on the rough roads, gravel road, hill and grass
When the bumper height is changed due to heavy load
When the sensing portion is frozen
When the sensing portion is covered by rain, water drops, snow or mud
When receiving other ultrasonic signals (metal sound or air braking noises from heavy
commercial vehicles)
When a high-power radio is turned on
When some accessories are attached in detecting ranges -
-
-
-
-
-
- 4. Not defective but may cause malfunction

09-58790-01
Parking Aid Unit
1. GENERAL INFORMATION
1) Components and Function
The parking aid system uses three
piezoelectric ceramic sensors inside the rear
bumper to measure the vertical and horizontal
distances to the obstacles. The parking aid
system has a separate unit that sends signal
to the buzzer when reverse parking to notify
the driver of the distance to obstacle. When
placing the gear selector lever to “R" position,
this unit activates the sensor to measure the
distance between the object and the bumper.
The existing PAS unit displays the
malfunctions using the LED when there are
any defects in sending/receiving signal or the
open circuit to sensor. On the other hand, the
PAS unit of KORANDO SPORTS informs the
malfunction of the relevant sensor using a
buzzer.
STICS
PAS buzzer
LH/RH sensor
Center sensor

01-4
This indicator shows the current position of
the gear.
In normal mode: P, R, N, D
Gear indication in “M” mode: 1, 2, 3, 4, 5, 6
Driving gear can be adjusted by operating
the tip switch after moving the gear select
lever in “M” position.
Shift down Shift up
Tip switch on steering wheel ▶
Gear position display on instrument cluste▶
Gear select lever ▶
Mode Switch
W :
S :
Selection of Manual/
Automatic Shift Function
D :
M :Shift Lock Release Button Hole
when Locked in the "P" Position
If you cannot move the gear
select lever from the "P" position,
try to move the lever while
pushing down here with a sharp
object such as a ballpoint pen.
For your safety, turn off the
engine and depress the brake
pedal before the attempt. Tip Switch in “M” Position (Manual Gear Shift)
The shiftable gear can be adjusted by moving this switch to forward and rearward when the
gear select lever is in “M” position.
Positions of gear
select lever
P : Parking
R : Reverse
N : Neutral
D : Drive
Winter mode
Standard mode (Use the
standard mode in normal
driving conditions.)
Automatic shift according to
the driving condition
Manual shift

01-76810-01
▶ Step 5
Ambient
temperature
display
51
Interior
temperature
displayIntake air temperature
display
Ambient
temperature
sensorInterior
temperature
sensorIntake air
temperature sensor
▶ Step 6
To enter the step 6 from 5, turn the fan speed dial lightly toward the right not using the
temperature control dial. In this step, you can decrease or increase by up to 3 degrees
from the temperature set on the A/C controller. -You can check that the temperature value from each temperature sensor is displayed
properly in this step. Pressing the defroster switch changes the temperature value that
appears on the display in the order as follows: -
2) Self-diagnosis step
(1) Step 1
Turn the ignition ON and press the OFF switch for 5 sec. or more within 10 sec.
Then the first step of the self-diagnosis is started as shown in the below figure.
2. Display for checking VFD and all LED segments
1. Press OFF switch for 5 sec. or more