display SSANGYONG NEW ACTYON SPORTS 2012 Service Manual

03-6
2) Diagnostic Test for Engine Fuel System
(1) Overview
If a DTC is displayed on the diagnostic device, check the low pressure- and high pressure fuel
systems before removing the components.
To run the system properly, the electric system must be intact but for the DI engine, the fuel
pressure should be measured also when there is a malfunction even after the diagnostic test with
a diagnostic device.
(2) Hydraulic system

03-12
(5) High Pressure System Pressure Test
Fuel rail pressure test ▶
Disconnect the fuel rail pressure sensor
connector and then IMV connector. 1.
Connect the pressure tester to the fuel rail
pressure sensor connector. 2.
Crank the engine 2 times for 5 seconds. 3.
Read the highest pressure value
displayed on the tester display.
If the highest pressure value is 1,050 bar
or less, refer to the section "Fuel System
Check Process". -
-

03-132210-01
How To Use Pressure Tester ▶
Press the "TEST" button on the tester to
check if the message "TEST?" is
displayed.
If the button is pressed again at 4 seconds
after starting engine cranking, the highest
pressure is displayed on the tester. 1.
2.
The fuel rail pressure value can be checked using a diagnostic device.

03-172210-01
HP pump pressure test ▶
Prepare a special tool for high pressure
test and clean it thoroughly to prevent
foreign materials from entering. 1.
Disconnect the high pressure fuel supply
pipe on the HP pump and install the close
rail in the tool kit. 2.
Connect the other end of the close rail to
the fuel rail for test. 3.
Disconnect the return hose for HP pump
and connect the clear hose and connect
its the other end to the return port of the
fuel rail for test. 4.
Connect the digital tester connector to the
sensor connector of the fuel rail for test.
Crank the engine 2 times for 5 seconds after
removing the IMV connector and fuel rail
pressure sensor connector.
Read the pressure value displayed on the
tester display is within the specified 5.
6.
7.
Specification1,050 bar or more

09-71451-01
(1) Checking
Using battery tester ▶
PASS (11.0 V or more): Explain to the customer that the battery is reusable.
Need to be charged (9.0 to 11.0 V): Charge the battery with a charger and reinstall it. Explain it
to the customer.
Need to be replaced (9.0 V or more): The battery should be replaced due to overdischarging. -
-
-
(2) How to use battery tester
How it works and How to use it ▶
Determine battery capacity by fixing current
(load capacity) and time and varying
voltage.
Determine battery capacity based on the
amount of voltage drop when discharging a
fixed load capacity (120 A) for 5 seconds.
Connect the tester to the battery and read
the display while applying a load for 5
seconds. -
-
-
How to read display ▶
Red area (①): overdischarge or faulty
battery
Yellow area (②): Need to be charged (using
a vehicle alternator and a battery charger)
Green area (③): Normal
Red area on the left-hand side of OK (④):
Impossible to charge with an alternator
Green area with OK (⑤): Normally charged
Red area on the right-hand side of OK (⑥):
Overcharged by an alternator태 -
-
-
-
-
-

02-618710-01
4) How to Code REKES Key
If you replace the REKES key or immobilizer & rechargeable key to new one, you should code the
REKES key using the diagnostic device. (maximum 5)
Connect the diagnostic device to the vehilce and select the vehicle type and system (RK-
STICS). When the following screen is displayed, select 'REMOCON CODING'. 1.
Remove the remote control key from the ignition key box and press 'Next'. Press the door
UNLOCK (PANIC) button on the remote control key once (for approx. 2 seconds or longer). 2.

02-62
When you code newly purchased remote control key:
When you lost the remote control key and purchase a new one, if you code only the newly
purchased one, the existing remote control key becomes unavailable. You must code the
newly purchased remote control key together with the existing one. -The first key coding completion screen is displayed with beep sound as follows: Press 'Next'
and perform the second remote control key coding in the same way. 3.
When the second key coding is completed, the following screen is displayed. Finish the
remote control key coding by pressing 'Previous'. 4.
Exit the diagnostic screen, remove the device from the diagnostic connector and perform the
function test for the remote control key. If it does not work well, perform the above procedures
again. 5.

03-57010-06
Item Front view Rear view Internal structure
Rechargeable key
RKSTICS key
DifferenceNoneLabel color,
Specification displayBattery specification
and
transponder function
2. OVERVIEW
The functions of the immobilizer and the rechargeable key are controlled by the immobilizer &
rechargeable unit. Both functions are used in this system. This immobilizer & rechargeable unit
starts the engine by communicating with the engine control unit and increases the life of the
existing REKES battery by charging the battery of the remote control key.
Immobilizer & rechargeable unit
Rechargeable Key VS RKSTICS Key ▶
Rechargeable
battery used

04-38210-01
1. SPECIFICATIONS
Item Specification
Rated voltage DC 13.5 V
Operating voltage DC 9 V ~ 16 V
Checking voltage DC 13.5 V
Operating temperature-30℃ ~ +80℃
Storage temperature-40℃ ~ +85℃
Illumination color Dial White
Pointer Red
LCD Red
Gear position display in A/T
(Left hand of LCD display)P, R, N, D, 1, 2, 3, 4, 5 and 6

04-4
1. DESCRIPTIONS OF INDICATOR DISPLAY
Tachometer
ESP indicator/warning light
Immobilizer indicator
Glow indicator
Front fog light indicator
High beam indicator
ESP OFF indicator
Seat belt reminder (driver’s seat)
Seat belt reminder (passenger’s seat)
Engine oil pressure warning light
LCD Display
Engine overheat warning light
Engine check warning light
Auto cruise indicator
Light indicator
Winter mode indicator 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.Engine hood open warning light
Battery charge warning light
Hazard Indicator
Water separator warning light
Air bag warning light
4WD CHECK warning light
4WD LOW indicator
4WD HIGH indicator
Speedometer
Turn signal indicator
Coolant temperature gauge
Brake warning light
Door ajar warning light
ABS warning light
Fuel gauge
Low fuel level warning light 17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32. It sends and receives information to/from each unit through CAN communication line. The LCD
display and separate ESP ON/OFF indicator are newly added.