sensor SSANGYONG NEW ACTYON SPORTS 2012 User Guide

(2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION (1) CONNECTOR INFORMATION 3) BLOWER, ACTUATOR (MODE, INTAKE), AMBI SENSOR

02-6
1533-31 Oil dipstick gauge
Changed the location
1719-40 Intake manifold
T-MAP sensor installing hole (1), intake duct
mounting flange (2), intake duct mounting
boss (3)
1719-29 Intake duct and bracket
Changed intake duct, air intake direction,
location of T-MAP sensor
D20DTF (Korando C)
3. MAJOR CHANGES IN ENGINE (RH)
OldNew
OldNew
OldNew
T-MAP sensorT-MAP sensor
1533-30 Oil level sensor & oil pressure
switch
OldNew
OldNew
Oil pressure switchOil level sensor
1225-01 Cylinder head cover & PCV valve
Changed the location of blow-by hose and
PCV valve

02-70000-00
1719-09 Acoustic cover
Changed the design1543-01 Steering pump assembly
Introduced reservoir integrated tpe steering
pump
D20DTR (Actyon Sports)
OldNew
OldNew
OldNew
Power steering pump
Old
New
1533-30 Coolant outlet pipe
OldNew
Coolant temperature sensor hole
EGR cooler
outlet
Coolant temperature sensor hole
EGR cooler outletCoolant outlet pipe
1520-21 Coolant outlet port
Changed the location of coolant
temperature sensor and deleted the
coolant outlet port from turbocharger
1793-23 EGR cooler & coolant outlet
hose

02-8
1533-08 Oil pan1533-48 Ladder frame
Deleted MBU, introduced ladder frame
1914-01 Turbocharger
Changed the cooling ty
pe (water cooling → air
cooling)
1729-01 Exhaust manifold
Changed the location of mounting flange and
exhaust gas temperature sensor mounting hole
1127-01 Cylinder block
D20DTF (Korando C)
4. MAJOR CHANGES IN ENGINE (LH)
OldNew
OldNew
OldNew
Exhaust gas
temperature
OldNew
OldNew
Plug screwPipe screw
Ladder frame

01-4
2. MAJOR COMPONENTS
Front view ▶
Vacuum pump
Oil filter assembly
Camshaft position sensor
Power steering pump pulley
Water pump pulley
Alternator pulley
Idler pulley No. 2
A/C compressor pulley
Auto tensioner
Idler pulley No. 1
Isolation damper
Rear view ▶
E-EGR valve
Fuel temperature sensor
Fuel HP pump assembly
Coolant temperature sensor
IMV valve Crankshaft position sensor
Oil pressure switch

01-50000-00
Right view ▶
Front exhaust gas
temperature sensor
Oil dipstick tube &
gauge assembly
E-VGT actuator
E-VGT turbocharger
Coolant screw plug
Oil drain plug
Left view ▶
Thermostat assembly
Variable swirl valve assembly
E-EGR valve
E-EGR solenoid valve
EGR cooler
Electronic throttle body
Oil cooler assembly

01-110000-00
6. CODING AND INITIALIZATION
1) Engine Variant Coding
Unit Selection Description Remarks
PTC auxilary heater NO For PTC auxilary heater
equipped vehicle, select
"YES".-
YES YES
Glow plug Relay (K-line) Select "AQGS". -
AQGS (CAN) AQGS (CAN)
Transmission 6-speed M/T "DSI 6 AT" is selected
automatically.Select
5-speed A/T (DC 5 AT) -
6-speed A/T (DSI 6 AT) Select
Pressure sensor for
A/C refrigerantNO Select the appropriate
system.-
Type Pressure
sensor for A/C
refrigerant
Immobilizer NO Select "YES" if the vehicle
has immobilizer.-
YES YES
Vehicle speed input
typeCAN Select "CAN" if the vehicle
has ABS or ESPCAN
WIRE -
Fan 2 relays Select "PWM". -
PWM fan PWM fan
Auto cruise NO Select "YES" if the vehicle
has cruise contro.-
YES YES
G-sensor NO 2WD ABS & Non-ABS: NO
4WD ABS & ESP: YESSelect
YES Select

02-30000-00
1. SPECIFICATION
Unit Description Specification Remark
Cylinder head Height 142.9 to 143.1 mm -
Flatness below 0.1 mm -
Valve protrusion Intake valve 0.1 to 0.7 mm -
Exhaust valve 0.1 to 0.7 mm -
Flatness on manifold
sideIntake manifold 0.08 mm -
Exhaust manifold 0.08 mm -
Connecting rod End play 0.5 to 1.5 mm -
Camshaft Axial end play Intake 0.1 to 0.35 mm -
Exhaust 0.1 to 0.35 mm -
Camshaft
position sensorDistance between Camshaft position
sensor and sprocket0.20 to 1.80 mm -
Valve Clearance between
valve and pistonIntake Approx. 0.7 mm -
Exhaust Approx. 0.8 mm -
Valve recess Intake 0.1 to 0.7 mm -
Exhaust -
Cylinder block Piston protrusion 0.541 to 0.649 mm -
Piston ring TOP ring end gap 0.20 to 0.35 mm -
2nd ring end gap 0.35 to 0.50 mm -
3rd ring end gap 0.2 to 0.40 mm -
Offset 0.3 mm -
Head gasket Piston protrusion 0.475~0.540 1.2t -
0.541 to 0.649 1.3t -
0.650 to 0.745 1.4t -

02-4
2. TIGHTENING TORQUE
Component SizeBolt
QuantitySpecified torque
(Nm)Remark
(Total torque)
Main bearing capM12×8210 55±5Nm,
180˚Not re-usable
Connecting rod capM9×52840±5Nm,
90˚+10˚50 to 80 Nm
Rear coverM6×20610 ± 1 Nm-
Oil pumpM8×35SOC325 ± 2.5 Nm-
FlywheelM10×22845 ± 5 Nm,
90˚+10˚60 to 100 Nm
Crankshaft center boltM20×851200 ± 20 Nm,
180˚+20˚660 to 720 Nm
Not re-usable
Oil panM6×201810 ± 1 Nm-
M6×35210 ± 1 Nm-
M6×85210 ± 1 Nm-
M6×120210 ± 1 Nm-
M8×40225 ± 2.5 Nm-
HP pump main nutM14×1.5-8-1165 ± 5 Nm-
HP pump boltM8×55325 ± 2.5 Nm-
Cylinder headM13×15012 85Nm
270°±10°-
Camshaft capM6×301610 ± 1 Nm -
M8×60425 ± 2.5 Nm -
Exhaust stud bolt 1015±1.5Nm-
Exhaust sprocket boltM11×40130 ± 3 Nm -
Chain tensioner screw
boltM38×1.5 125±2.5Nm -
Coolant temperature
sensor120±2.0Nm -
Auto tensionerM8×30(LOW) 125±2.5Nm -
M10×75(Upper) 155±5.5Nm -
Coolant pumpM6×50 110±1.0Nm -

02-50000-00
Component SizeBolt
QuantitySpecified torque
(Nm)Remark
(Total torque)
Hot water inlet pipeM6×16 2 10±1Nm -
AlternatorM10×90 1 25±2.5Nm -
M10×116 1 46±4.6Nm -
A/C bracketM8×25 4 7.8~11.8Nm -
A/C sub bracketM6×25 4 10±1Nm -
Intake manifoldM8×35 2 25±2.5Nm -
M8×110 6 25±2.5Nm -
Oil filter moduleM8×40 6 25±2.5Nm -
M8×20 1 25±2.5Nm -
M8×140 2 25±2.5Nm -
Knock sensorM8×28 2 20±5Nm -
Cam position sensorM8×14 1 10~14Nm -
Booster pressure
sensorM6×20 2 10±1Nm -
Exhaust manifold M8 10 40±4Nm -
Turbocharger M8 3 25±2.5Nm -
Support bolt 1 25±2.5Nm -
Support nut M8 1 25±2.5Nm -
T/C oil supply pipe M6(block side) 1 10±1.0Nm -
M6(turbo side) 1 17±2.0Nm -
T/C oil return pipeM6×16(turbo side)2 10±1Nm -
M6×16(block side)2 10±1Nm -
EGR valveM8×22 2 25±2.5Nm -
EGR pipe bolt
(Intake side)M8×16 2
25±2.5Nm -
EGR pipe bolt
(EGR cooler side)M8×16 2 25±2.5Nm -
EGR combination boltM6×16 4 10±1Nm -
M8×16 16 25±2.5Nm -
Idle pulley/Tensioner
pulley1 45±4.5Nm -