SSANGYONG NEW ACTYON SPORTS 2012 Service Manual

08-78610-09
3) Sensitivity Control
The wiper LOW relay is turned on and the wiper motor runs one cycle when the volume
<009a008c0095009a0090009b0090009d0090009b00a000470090009a004700900095008a0099008c0088009a008c008b0047004f008c009f00610047009a008c0095009a0090009b0090009d0090009b00a00047005700470d7d0047005800500047009e00
8f00900093008c0047009b008f008c00470090008e00950090>tion switch and the INT switch is
in the "ON" position, and the wiper motor is in "Parked" position). However, the wiper
motor can be operated only when the rain sensor detects the "Rain Detected" signal. 1.
If the volume sensitivity is changed more than 1 stage within 2 seconds, the wiper motor runs
only one cycle.
4) Auto Light Control
Only when the auto light switch is in "AUTO" position, it controls the tail lamp and
headlamp by communicating with the rain sensor (while the ignition key is in "ON"
position). 1.

08-8
5) When Wiper Parking Signal is Abnormal
The wiper system continuously outputs the parking signal of current sensitivity when the
parking terminal is grounded (while the ignition key is in "ON" position and the INT switch is
in "ON" position). 1.
When the parking terminal is fixed to IGN, the wiper system outputs the wiper operating
signal for 2 seconds, then continuously outputs the wiper parking signal.
※ The wiper motor runs only when the rain sensor requires the wiper operation. 2.

08-98610-09
6) Defective Rain Sensor
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 3 from 4 during receiving the malfunction signal from the rain
sensor, while the ignition key is in "ON" position and the wiper switch is in "ON" position. 2.The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 2 from 3 during receiving the malfunction signal from the rain
sensor, while the ignition key is in "ON" position and the wiper switch is in "ON" position. 1.

08-10
7) Speed Sensitive INT Wiper
Calculates and converts the Intermittent interval automatically by obtaining the INT VOLUME
when the ignition switch and the INT switch is in the "ON" position.
The wipers are operated in vehicle speed sensitive mode as soon as turning the INT auto
switch to the "ON" position with the ignition key ON or turning the ignition key to the "ON"
position with the INT auto switch ON.
This applies to the vehicle without the rain sensor. -
-
※
Controls the wiper intermittent operation by the values from the vehicle speed and the setting
value.

08-110000-00
Pause Time Table of Vehicle Speed Coupled INT Wiper ▶
Speed sensitive INT (intermittent) wiper 1.Pause time against vehicle speed ▶
Cautions for wiper control ※
The wiper relay continues to output for remaining "ON" time even when the INT switch is
turned off during its operation.
IGN switch "ON", INT switch "OFF": Resume the intermittent time when turning "ON".
IGN switch "ON", INT switch "ON": Resume the intermittent time when turning "ON". -
-
-
Controls when the wiper motor parking is defective 2.
The wiper relay continues to output when the parking terminal is fixed at the ground or
IGN while the wiper relay is "ON" i.e., with the INT switch ON or washer switch ON. (The
output stops immediately after turning off the switch) -

08-12
Rain detected headlamp: If it rains heavy which requires the highest INT speed (almost
LOW), the headlamps are turned on automatically.
Night detected wiping: When the auto light control turns on the headlamps and the rain
sensor detects the rain, the wiper sensitivity is automatically increased by one level in
comparison with daytime.
(i.e. the AUTO wiper switch is at the 3rd level, but the wiper operates at the 4th level.) 1.
2.
3. OPERATION MODE OF RAIN SENSING WIPER SYSTEM

09-38790-01
1. COMPONENT SPECIFICATIONS
The PAS (parking aid system) emits the ultrasonic wave signals from the sensors on the rear
bumper at a specific interval
and detects the reflected signals from obstacles when reversing. The alarm interval increases as
the obstacle approaches.
This supplementary system is useful to measure the distance when parking.
Parking Aid Unit ▶
Parking Aid Sensor ▶
Detecting type: Ultrasonic wave (Piezo
ceramic element)
Calculates the distance between the
sensor and the object by calculating the
return time of the emitted the ultrasonic
wave
Frequency used: 50 KHz ± 1 KHz
Detection distance: 30 cm ~ 120 cm
(based on lineal distance between sensor
and obstacle)
Tolerance: ± 10 cm
Sensor detection range (at -6 dB) -
-
-
-
-
LH/RH sensor
Center sensor
Item Value Item Value
Rated voltage DC 12 V Operating temperature-30˚C ~ +80˚C
Operating voltage DC 9 V ~ 16 V Storage temperature-40˚C ~ +85˚C
Current
consumptionUnit 100 mA or less Relative humidity 95% RH max
Sensor 20 mA or less (each)
WeightUnit72 ± 10 g
Sensor40 ± 5 g

09-4
2. CAUTIONS
Note that the display does not show everything in the rear area. Always check nobody,
especially animals and children, is behind the vehicle when parking or reversing.
If you can not properly check the vehicle behind, get out of the vehicle and then visually
check it.
The parking aid system is just a supplemental device to help your parking.
Always keep the safety precautions.
Do not press or shock the sensors by hitting or using a high-pressure water gun while
washing, since it may damage the sensors.
If the system is in normal operating condition, a short beep sounds when the shift lever is
moved into "R" position with the ignition key "ON". -
-
-
-
-
-
The parking aid system will not work or improperly work under following cases: ▶
1. Certain obstacles that sensors can not detect
Thin and narrow objects, such as wires, ropes, chains
Cotton, sponge, clothes, snow; that absorb ultrasonic waves
Obstacles lower than the bumper (ex. drain ditch or mud puddle) -
-
-
2. Not defective but improperly working
When the sensing portion is frozen (operates normally after thawed)
When the sensing portion is covered by rain, water drops, snow or mud (operates normally
after cleaned)
When receiving other ultrasonic signals (metal sound or air braking noises from heavy
commercial vehicles)
When a high-power radio is turned on -
-
-
-
3. Narrowed sensing area
When the sensing portion is partially covered by snow or mud (operates normally after
cleaned)
<007a009c009900990096009c0095008b00900095008e0047009b008c00940097008c00990088009b009c0099008c00470096008d0047009a008c0095009a0096009900470090009a0047009b009600960047008f0090008e008f0047004f00880097009700
990096009f005500470096009d008c00990047005f005700b6>C) or too low (approx.
below -30°C) -
-
When driving on the rough roads, gravel road, hill and grass
When the bumper height is changed due to heavy load
When the sensing portion is frozen
When the sensing portion is covered by rain, water drops, snow or mud
When receiving other ultrasonic signals (metal sound or air braking noises from heavy
commercial vehicles)
When a high-power radio is turned on
When some accessories are attached in detecting ranges -
-
-
-
-
-
- 4. Not defective but may cause malfunction

09-58790-01
Parking Aid Unit
1. GENERAL INFORMATION
1) Components and Function
The parking aid system uses three
piezoelectric ceramic sensors inside the rear
bumper to measure the vertical and horizontal
distances to the obstacles. The parking aid
system has a separate unit that sends signal
to the buzzer when reverse parking to notify
the driver of the distance to obstacle. When
placing the gear selector lever to “R" position,
this unit activates the sensor to measure the
distance between the object and the bumper.
The existing PAS unit displays the
malfunctions using the LED when there are
any defects in sending/receiving signal or the
open circuit to sensor. On the other hand, the
PAS unit of KORANDO SPORTS informs the
malfunction of the relevant sensor using a
buzzer.
STICS
PAS buzzer
LH/RH sensor
Center sensor

09-6
2. ALARM INTERVAL
While reversing, if obstacles are within stage 1, the warning beep sounds with long intervals. If
within stage 2, the warning beep sounds with short intervals and if within stage 3, the warning
beep sounds continuously.
1) Sensing Distance and Range
Sensor detection range
Within 20 cm from the ground (Intrinsically, supersonic wave sensors may not detect
obstacles within 20 cm from the ground)(Area 1)
Obstacles may not be detected within 80 cm from the sensor(Area 2)
Sensor may not detect zone within 30 cm from the rear bumper (Area 3) -
-
-